WiFi-N or WiFi-B/G I have a Dell P513w Inkjet Printer and am upgrading my printer firmware to the latest release. How do I determine if I use firmware version WiFi-N or WiFi-B/G when updating? Whether or not this is the level that I should use, my current firmaware level is "C" (WiFi-N). If I am to use WiFi-B/G how do I change firmware levels?
Using Windows 7 64-bit
Region : Others
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 1.8
ISP :
Region : Israel
Model : TL-WR1043ND
Hardware Version (On the back cover): V1.8
From web interface:
Firmware Version:3.13.4 Build 110429 Rel.36959n
Hardware Version:WR1043ND v1 00000000
ISP : Free
1. about USB Printer Controller
I connect my printer HP office jet 5610 All in one, his drivers installed on my computer (windows 7 ultimate, 32 bit). Irun the software "USB Printer Controller" and i didn't seeing anything. Can not click on any button. BTW, i changed the IP range from 192.168.1.1 to 10.0.0.100-10.0.0.139 and my router web interface at 10.0.0.140, if it's changing something.
2. About upgrade the router's firmware, it's safe that I'll upgrading it?
The last version : TL-WR1043ND_V1_120405
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
View 2 Replies View RelatedI have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
View 12 Replies View RelatedI need to upgrade WCS firmware. Currently i am running with 7.0.172.0 .
View 1 Replies View RelatedHave the DIR-655 Hardware Version A1. Firmware 1.00NA dated Feb 2010. When I try to upload ANY firmware update from the DLINK site, it says that it is not for that device or is corrupt.
View 5 Replies View RelatedI have the DIR-655 . I decided to do a firmware update to Firmware Version: 1.35NA and now I having a problem connecting remotely from outside the network to a computer on my LAN. I use a software called Radmin to connect to one of my LAN computers behind the DIR-655 router and now since I did the update I cannot connect because the router is blocking the request, here is the router log info
[code]...
I have a DIR-615 Ver. C1 f/w3.00. We have been having trouble with the the signal becoming weak or non-existent, so I decided to see if a firmware upgrade would solve the problem. I have attempted to upgrade to DIR615C1C2_FW301B11.bin and to DIR615C1_FW313NAB09.bin with the same result for both of them - with several attempts for each.
The message I get is: "The uploaded firmware file may not be correct. You may have uploaded a file that is not intended for this device, or the uploaded file may be corrupted.
If the uploaded file is correct, it is possible that the device may be too busy to properly receive it right now. In this case, please try the upload again. It is also possible that you are logged in as a 'user' instead of an 'admin' - only administrators can upload new firmware.
The Gateway will not be reprogrammed."
I have disconnected all other devices to reduce traffic, I have attempted the upload multiple times for 3.01 and 3.13NA, I am logged in as the admin, and I believe the files are proper for this hardware version.
Is there something I am missing that prevents me from performing a firmware upgrade?
Recently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedI currently have 3 WAP4410n's (actually, they're WAP4410N-E V02s) that have been really unreliable since I got them - so much so that we've had to cron a restart script on another server which is frankly ridiculous - they've always run firmware version 2.0.2.1.
I've tried updating the firmware to new versions in the past with no success - when I do so, it looks like everything's fine, but when I log back in, the fixed IP address information isn't shown, and the wireless is disabled. I can enable it, but I can't select a channel.
At this point, I have to revert back to the old firmware. I've tried restoring to factory setttings before and after the firmware flash, but this hasn't changed anything.
However, recently I was able to flash firmware 2.0.5.3 onto only one of the routers - it worked fine and all information was displayed and wireless enabled correctly. However on the other two, no matter what I try, the firmware won't upgrade succesfully - it looks like everything's fine, but the fixed IP information isn't shown and wireless/channels are disabled.
I've been using ZYXEL PLA-401 v1 Homeplug adapters for years to connect various devices to my router for a "more stable" than wireless connection. This worked fine in my last house, connecting a switch in our office to the router. We've now moved and I have got some more homeplug adapters to make a few other more reliable connections.
Problem is, the new adapters can't see the old adapters on the homeplug network. They can see each other, as can the old ones. I suspect a firmware or network name mismatch - I've tried to change settings on each of them but the Zyxel utility doesn't appear to do much. I can't set the DAK names, nor can I change the network names. The firmware update utility doesn't work on Windows 7 (gives a cannot find Windows path error).
using the Zyxel configuration utility and firmware upgrade tool on Windows 7 / Ubuntu?
I've got three WG302s of which the certificates on all of them are up. I've begun the process of replacing the firmware on one of them with OpenWrt. I've been using this to get the job done: url...I've been able to edit it up to the point of using fconfig to edit the boot script. I understand that I just need to edit two lines and the firmware replacement will be complete. [code]I've looked up fconfig commands to see if I could figure out how to edit the script lines.
View 1 Replies View RelatedI tried to find a suitable firmware for it & found this, Wireless Router, but when I upgrade the device with this firmware , every thing go wrong .. no english language cant upgrade anymore I tried to reset the device to its factory defaults by pressing the reset botumn but the nothing changes
View 8 Replies View Relatedi have hardware AirLive wha 5500cpe-nt. this device have upgrade to dd-wrt firmware. but after upgrade i can't access again. i can't find ip address because dhcp service not active, so can't get ip for my laptop...
View 1 Replies View RelatedI have a dlink dir 615 router that has started to drop wireless signal continuously (as in once every minute or so). I looked into potential issues and all signs point to firmware upgrading as the solution. I even looked up the latest firmware for my unit and it indicate that it repaired wireless connection issues. But my issue is that I downloaded the latest firmware and it won't let me install it. It keeps saying that it isn't the right file or my router is too busy to complete the upload.
View 4 Replies View RelatedWell this one should be in the "Firmware DOs and DONTs" post. I updated to FW 1.11 over wifi and apparently this will corrupt the camera so it needs serviving. Would have been nice to know that before I did it. Since the upgrade from 1.02 1030 I get this note:The throughput of the SD Card on your camera is not currently enough for recording. We suggest you to reformat the SD Card or replace it with a higher class one.
View 12 Replies View RelatedIs there a firmware upgrade for the Linksys CM100? My CM100's web interface keeps crashing after a week of use.
View 4 Replies View RelatedI wanted to upgrade to the latest firmware (2.03NA). Something went wrong and now the router comes up with the orange light flashing. So the system is in emergency firmware upgrade mode. I set my IP to 192.168.0.2 and connect to the web interface at 192.168.0.1. I see a page with "Firmware Upgrade System" and "Version 1.0.0.2". So far so good. I can now select the firmware and click "send". But then nothing really happens. I can wait for a couple of minutes and then run into a timeout. I tried different browsers (Linux: Firefox, Chrome, etc). I even tried it Windows 7 with IE 8 and I get the same result. It seems that the cgi (192.168.0.1./cgi/index) is not really doing anything?
View 12 Replies View RelatedI hope that we can get this DIR-825 back from the dead. I did the first portion of the 2.05NA upgrade while wired into LAN1 on the unit, after the reboot the power light went Amber and the unit would no longer respond to pings. I have searched around for various reset methods but have not been able to find a guide or a definitive current D-Link tech manual on how to fix a bad flash. I have tried pinging/arping/web browsing its default IP and the IP I had it set to to no avail.
View 2 Replies View RelatedLast week I upgraded the firmware to 1.13NA and ever since, the wireless network has been slooooooow (wired is fine). If the laptop/ipad/phone is in the same room as the router, things are fine. Anywhere else in the house, the speed drops off to almost nothing even though the signal strength is very good. For example: Under the "Speed" section of my "Wireless Network Connection Status" on my laptop, I'm seeing 150.0Mbps in the same room as the router, 25.0 Mbps in the hallway and 1.0 Mbps about 5 steps further away. All the while, the signal strength is showing Excellent.Speakeasy speedtest: Wired 23.36 Mbps, wireless at the end of the hallway, .12 Mbps.
Hardware version: A1
Firmware version: 1.13NA
Cicso Cable modem DPQ3212
Im having a bit of trouble, how am i supposed to update my router, i have DLed the tarballs from GPL and now im not sure how to update it, do i have to makefile? (im using ubuntu by the way which is handy if i have to build it!) and if i do have to makefile how do i do it?
View 2 Replies View RelatedI am trying to update my firmware from v1 to v2 on my F5D9231-4 Router, after downloading from the support page and trying to install it I get the following error "Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again" I double checked the model numbers.
View 2 Replies View RelatedF5D8233-4 N Wireless Router - Firmware Update,l I am trying to upgrade the firmware of this router which currently it's 3.01.29 to the latest one which is 4.00.04 but every time I try to manually install it, it comes back with an error message saying it's not the tight update but it is.
View 1 Replies View RelatedIt baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies View RelatedI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies View RelatedWe have 2 ASA 5520s in active/standy. We run IOS 8.2(5)24 and I wondered if I need to upgrade as I see the versions have gone to 8.4 and beyond! We are not getting any issues and I'm aware of the difficult migration from 8.2 to 8.4 etc due to the NAT change.
View 3 Replies View RelatedI´ve a problem with my "old" PIX515e device. I wanted to flash this device to a new firmware level but forgot to disable the "lost enable" password before. So I started to make the firmware upgrade on my device, ended up with "flashfs" is busy and I should start the enabled modus and "copy flash tftp" to activate the new flash version. Unfortunalty I cannot do this because I´ve lost my password. When I´m trying to boot this device up now, it will end with a error message...
Unable to locate boot image configuration
Booting first image in flash
No bootable image in flash. Please download an image from a network server in the monitor mode
Failed to find an image to boot
As mentioned, when I will load a new flash image over monitor mode, i cannot activate that image because of flashfs is busy.The password reset bin files will not work too. I tried that too but this one will recongnize no active installed flash.Is there any way to reanimate my PIX515e? In newer devices there are possibilites to work with changing config register but I´ve found nothing about that for a PIX515e.
I cannot find instructions on how to use the latest 4.0.18 ADSL firmware on an 887 router.
I've downloaded adsl_alc_20190_4.0.018.bin from the website and copied it to flash, but cannot find any instructions on applying the firmware. Tried rebooting but made no difference.
What commands, etc, am I meant to use to make use of this ADSL firmware release ?
We have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedI've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
After much investigation I finally found what I thought was the firmware upgrade for my WAP4400N access point, I downloaded the file which is a .img file which seems a bit off I think. Anyway when I go to the admin page it decides its an unknown file format. Could someone explain what I am supposed to do with it!
I have to say I am very dissapointed with the whole support function of this site it is very hard to navigate and when you do think you have the correct link, its not. How very helpful!!! I suppose there are networking gurus who look after multi 1000 user systems who understand how the site works and think its fantastic. I support 5 PC's and 7 laptops on top of my normal job, it should be easier.