Linksys Cable / DSL :: 2960 Switch Will Work With SMCD3G CCR Gateway
Feb 29, 2012
I am looking to upgrade my dumb switches to a Cisco 2960 switch. I wanted to check and make sure that this configuration would be supported. I will need to setup 4 vlans on the Cisco 2960 switch, 1 for vmotion traffic, that would not have internet access, one for management traffic that would not have internet access, one for standard server traffic and one for vmserver traffic, those would both need internet access. Would the Cisco switch work with the SMCD3G-CCR gateway ok, or would I need another router in order to do this?
View 1 Replies
ADVERTISEMENT
Apr 21, 2011
I'm trying to network a small office and have the following devices:
SMCD3G Cable Modem
Belkin Play N600 Router
Digi Mil-H1130 8 Port Ethernet SOHO Hub
Hubbel Cat5 Patch Panel (goes up to 12)
We're replacing our DSL line with a Cable line. Our DSL was a one piece wireless router/modem. When it was installed, it was inside our office, next to the server, and plugged into Wall Jack 1 for all the other computers to connect to. Our server plugged into this modem/router. We didn't have the Belkin Router at the time. The Patch Panel wires went into the Hub behind our office and everything was fine.
The cable modem is now next to the Hub and Patch Panel. I bought the router since we didn't have the wireless feature that the DSL had and everyone I spoke to said I need a router to set up the office. I ran one of the LAN lines from the modem into the Router where it says Modem (WAN). From the Router, I ran the line 1 (LAN) into the Hub. (Does the number matter if nothing is plugged into it in our office?) No computer is able to connect to the internet except my laptop which connects wireless. It works fine.
Another problem. We have a server computer that's Unix based. In order for anyone to connect to the server to access the office software used, the IP address of the router must be 192.9.2.1 or the computer your using won't connect via Multiview 2000 Terminal Emulator. I can't connect to the server because the IP address of the router is still 192.168.2.1. I don't know where I have to go in the router settings to change it. I've tried a few spots and it tells me the IP address is invalid. The settings I had with the DSL modem/router were:
Modem IP address - 192.9.2.1
Subnet Mask - 255.255.255.0
DHCP Start Address - 192.9.2.100
DHCP End Address - 192.9.2.150
It's not like I need to run wires. Everything is set. If something is plugged into a wrong spot, I can switch it.
Additional info:
There are 4 computers in the office and 8 numbered wall jacks.
Server computer - Wall jack 8 (IP address of this machine - 192.9.2.25)
XP Machine 1 - Wall jack 4 (can't connect to server! No internet.)
XP Machine 2 - Wall jack 1 (Is able to connect to the server! No internet.)
Win CE Machine - Wall jack 9 -
I assume. I have a wire that goes through the wall on this machine and it isn't marked. (Rarely used so not sure about server connection)
Wireless Windows7 laptop - connects to the internet fine since it bypasses all these wires. Can't connect to server.
Under the DHCP client list, only 2 computers are listed. The one that has internet is my computer. The other computer listed is wall jack 4 and that has internet now.
my computer - 192.9.2.2
wall jack 4 - 192.9.2.3
The router IP is 192.168.2.1 and the Cable Modem is 10.1.10.11. If I type either number into my web browser it will take me to the router setup page. I don't know where/how to check if it's only one device acting as DHCP. What I want to do is be able to get online with all the computers as well as have access to the software on the server through the office wall jacks. In order to do that I need the router IP address to be 192.9.2.1 and then I'd be able to connect to it.
Right now, one computer is able to connect to the server via hard wire but can't connect to the internet.Another computer is able to connect to the internet via hard wire but can't connect to the server.My laptop can connect wireless to the internet but not the server. In a perferct world, all the computers should be able to connect to both the internet and the server. Right now, it's one or the other with both hard wired machines and I don't know why. Is there a wire not in the hub right? Is a patch panel wire plugged into the wrong port of the hub? I don't know what's supposed to go where. tell me "wire X from the modem goes to Port Z of the router, and Wire Y from the the router goes to number V on the Hub, and that wire goes to number T on the patch panel for the Port number R in the office to work..." I'll try it.
Then I think all I need to do is change the router's IP address to 192.9.2.1 and everyone should be able to connect to the server through the Multiview 2000 Terminal Emulator.When I tried to change the IP address on the router it's telling me it's not valid. Under LAN settings it says 192.168.2.1 - when I try to change it to 192.9.2.1 it tells me LAN IP address is invalid. I clicked on More Info below that in the router page and a pop up gives me info. It says:
The "IP address" is the Internal IP address of the Router. To access the advanced setupinterface, type this IP address into the address bar of your browser. This address can be changed if needed. To Change the IP address, type in the new IP address and click "ApplyChanges". The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:
192.168.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
10.y.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
172.z.y.x (where z is anything from 16 to 31, and y is anything between 0 and 255, and x is anything between 1 and 254.)
View 4 Replies
View Related
Aug 14, 2012
4500 switch is connected to 2960 switch.
4500 config
Vlan 10
name Data
It has ip helper configured that points to DHCP.From 4500 switch port - port x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.
2960 config
vlan 10
name data
All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960 to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured on 2960 switch?
View 6 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Apr 12, 2012
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
View 2 Replies
View Related
Mar 14, 2013
Our family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
View 9 Replies
View Related
Sep 17, 2012
When i connect two cisco 2960 series switchs via stright trough cable causes delay in transmission sw1 has vlans and having trunk port connected to router all vlans are able to access internet sw2 is connected to vlan5 on switch1 sw2 has factory default configuration computers on sw2 can access internet but I have low bandwith problem on sw2 there is transmission delay problem?
View 1 Replies
View Related
Dec 12, 2012
I planed to configure a new catalyst 2960 switch with console cable.
During the boot, all seems ok. but from my terminal client, I can't have access to configuration mode.Keyboard or Terminal client is not sending commands to the switch.
The terminal is blocked on this line Compiled Tue 28-Sep-10 13:44 by prod_rel_team.what can I do to get access to the switch? [code]
View 3 Replies
View Related
Apr 21, 2011
I am having problems with my linksys wireless G ADSL gateway WAG54GS router. I am on Windows Vista/Internet Explorer. When I set up the router to work on the internet when I first bought it (several years ago), something must have gone wrong in the installation because it works only when connected to the computer by the lead, and NOT wirelessly.
While this is fine for general internet browsing etc on the main computer, my problem now is that I cannot connect anything else to it (such as my Playstation 3) because the router does not work wirelessly and I do not have the WPA key that the PS3 asks for. Is there any way can fix this without doing a complete reset on the router?
[ALSO: the router also periodically goes wrong, e.g. loses connection for no reason at all - I often have to disable and then enable the internet connection, or turn the router off for 15 seconds then switch it on again, and then it's fine again. I live in a rural area though, so it might be because of a poor connection. Our telephone connecton isn't very good either and sometimes goes wrong.]
View 4 Replies
View Related
Mar 23, 2013
Set up my WAG54G2 wireless gateway - I am able to connect to my LAN and the internet. The wireless works fine. However when I plug my server that use a wired connection into the modem/router,I lost the connection and I still unable to have internet at All. I use the firemware version V1.00.19.
View 6 Replies
View Related
Aug 30, 2012
I hard reset the router WAG160N and i can't access it on 192.168.1.1, i can connect to the wireless connection but it shows unindentified network, in properties gateway IP is absent. i also get 169.254.1.38 as IPv4.What could have happened to the modem, I can't use it at all at the moment?
View 3 Replies
View Related
Jul 10, 2012
I lost the disc to my X2000 gateway. Is there a download site for the software?
View 1 Replies
View Related
Jun 25, 2012
I have a Linksys WAG200G wireless ADSL router. So it has one ADSL(phone) line input port , 4 Ethernet ports and wireless router. My router is fine and works well on ADSL connections. But as I have switched to Comcast DOCSIS modem based internet connection now, I want to to setup this router as "Home Gateway" only and not the modem. My intention is to use- use 1 of the 4 ethernet ports at the back of router as an INPUT . I want to put the ethernet output of the DOCSIS modem into this INPUT- and then i want to use the remaining 3 Ethernet ports as OUTPUT ports from the router.- I also want to work my router as Wireless router.
My query is- Is this possible ? Basically use 1 port as an input and 3 as output.- I have tried different things - Using Bridge mode only. DHCP disabled but sometimes only wireless works and other times only LAN bridge setup works but both do not work together.- Also at times, one Ethernet port will work as an INPUT and 1 as an OUTPUT but other two remain disabled.
View 4 Replies
View Related
Feb 3, 2011
Does WAG160Nv2 support IPv6 addresses primarily for the Gateway's IP and thereafter about all IPs that need to be entered via the web interface?
View 9 Replies
View Related
Sep 20, 2012
i have a dpc3825 cable mdem gateway i spent 4 hours on the phone with charter yesterday i cant access the admin part of the router i go to 192.168.0.1 and up comes the setup username and password i have reset it numerous times i have left it blank as per instructions i have tried admin and blank cusadmin and password i cant get in
View 1 Replies
View Related
Nov 22, 2011
I configured my router Linksys WAG120N as DMZ, but not forward port 80, only port 80.
View 1 Replies
View Related
Mar 11, 2012
When I use only wireless B everything works fine. if I try to use both N and B none of them work and no device manages to connect wirellsly. Is there any special setting? I try to use standard Wep security because I have some older devices that don't support WPA.
View 3 Replies
View Related
Nov 1, 2012
I have a new X2000 v2 firmware 2.0.04. When I use it- itunes on my PC with seven don't work and give me error 8003.- the Apple Store on my iPad and on my iPhone don't download or upgrade the application.- itunes on my macbook air with mountain lions don't work and give me error 8003.- the download in ftp are very slowIf I use my old AG2241V2 all work fine.I have replicated the configution of old router on the new as far as possible but don't work.
View 3 Replies
View Related
Nov 8, 2011
I recently purchased a WAG320N router and have issues with access restrictions. Internet is shut down regardless of the time set with the policy or policies. I am using firmware version V1.00.12. Tried rebooting router, restoring factory defaults & restarting IMAC to no avail. Timezone checked and OK.
View 5 Replies
View Related
Sep 15, 2012
Here my network.dsl provider-->d-link modem (dhcp server, 192.168.1.1)-->X2000 (dhcp replay, 192.168.2.1(LAN IP))--> My laptop - X2000 config: dhcp replay: 192.168.1.1, LAN1 from d-link to WAN x2000 (blue rj45), X2000 have ip address from d-link. but my laptop can not receive ip address. X2000 is not gateway modem because it stuck after 1 day work. Can access to Web config page and internet.
View 4 Replies
View Related
Jul 30, 2011
I have noticed that on my WAG120N the WPS function doesn't work as it should (...at all). I tried connecting a blackberry, a playstation3 and 2 different laptops using the WPS option (button or PIN, doesn't matter) and the devices would simply not talk to each other. I can understand problems with the PS3 but the blackberry and the laptops were (and still are) able to connect using WPS on my previous router - WAG54G2. Pairing of the devices by supplying a password works fine, this is a problem only with the WPS functionality. My firmware is V1.00.16.
View 7 Replies
View Related
Aug 20, 2011
I have an ADSL Modem WAG200G Annex A, with latest firmware. I recently purchased a Linksys E2000 to upgrade my wireless to N, plus to get 4 gigabit Ethernet Ports for my NAS.
The problem is, I set WAG200G to "Bridge mode only", and from within E2000, I provided PPPoE credentials (user name and password), it does not work, no Internet connection!
Normally, with the WAG200G, PPPoE credential is set as followings (and it works)
Type: PPPoE Multiplexing: LLC Virtual Circuit: "0" for VPI (0~255) and "33" for VCI (0~65535) "Keep Alive" option
on E2000 Router, PPPoE does not have the above option for me to select. Only User Name and Password field
View 4 Replies
View Related
May 2, 2011
I have been using a Linksys Wireless-G ADSL WAG200G, Annex-A Gateway Router and it has been fine, now my ISP have told me that they are modernising the network and will need a router capable of managing ADSL2/ VDSL connections, so will my router be able to do that or will I have to buy a new one? It has firmware 1.01.09?Edit: I see in the DSL Modulation menu which is set at present to "Multimode" I also have options to select ADSL2, ADSL2+, ADSL2 AnnexM, ADSL2+ AnnexM and ASDL2 AnnexL but I do not see any mention of "VDSL"
View 2 Replies
View Related
Apr 9, 2011
How does the storage work with a WAG320N device via USB if I am using a Ubuntu 10.04/10.10 et al?
Does it look like an FTP site or can I just use it as a shared folder accessible though the normal folder directory structure from any machine on the network.
View 2 Replies
View Related
Dec 31, 2012
This will work, the Netgear I have does this seamlessly, how do I set this up as I cant find any info in the manuals/online help.
View 1 Replies
View Related
May 21, 2011
I purchased Linksys WAG160N (from a store) and I also have 7 Linksys SPA962 VOIP phones provided by MyNetPhone with service included. All tests we found out that this modem doesn't work with this VOIP phones. Somehow probably doesn't give access to MyNetPhone servers to get connection with this phones.I purchased an other one from DLINK and works perfect?
View 1 Replies
View Related
Dec 3, 2011
I found that if the WAG320N remain "on" during the night the day after will no longer work. It need to stay "off" for one day and than is starting to work again till another working's night! Why?
View 1 Replies
View Related
Feb 11, 2013
Im having a issue with that any of my computers without a wireless connection have been incapable of getting out on the internet with the new router that i got myself, i know the cables works etc, since they work perfectly fine with the old modem alone, but wont work at all with this unless on a computer with wireless connection
View 5 Replies
View Related
Apr 21, 2007
I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 Replies
View Related
Jul 31, 2012
I have a similar thread about this issue, the issue of this modem not support any kind of port forwarding actions... even disabling firewalls, using DMZ, port range forwarding the whole ip range , solves a thing...
it has upnp and port ranging features all over it but somehow it does not do it, and nobody cares excepty the ones that invested in it...
so if you are stuck with a router like me, dont bother wasting hours on it, and leave it to the people who are responsible for it.
View 2 Replies
View Related
Apr 8, 2010
I recently purchased a WAG320N, primarily for the faster networking speeds and the ability to attach a USB hard drive to my network.The only problem is that I have little idea how I get this network storage thing to work. Cisco haven't really supplied any documentation on how to work this.So far I've plugged in a hard drive and formatted it through the router's web interface, with no trouble at all.But, after doing this I have no idea how to access my hard drive on the network.I would assume that it would appear automatically on my network for me to access freely.
View 9 Replies
View Related
Nov 15, 2010
I have been playing with multicasting on my home network and have hit a problem in that all multicast messages seem to be spewing out over the WIFI regardless of whether there any any subscribers present or not which is swamping all other WIFI traffic. The wired LAN seems to be behaving just fine (no traffic on the wired network if no subscribers present).
how do I filter the multicast messages so that they are not sent out over the WIFI (unless a WIFI subscriber is present)? I have tried enabling the IGMP proxy but it makes no difference. I've tried messing with lots of other parameters too but no joy. Does multicast filtering actually work (or exist) on the WAG320N?
View 7 Replies
View Related
Aug 24, 2011
Is there any way I can make the cisco 857 router work on ADSL over ISDN?
View 2 Replies
View Related
