Linksys Wireless Router :: Can't Get GoFlex 3TB Drive To Work With E3000
Apr 2, 2011
Just bought a Seagate GoFlex 3TB external USB drive to connect to the E3000 router I recently purchased and it is dead. The LED light on the front of the drive doesn't come on when plugged into the router. It does when going direct to the PC and I can access the drive but when I go to the router,and try to explore the drive-nothing. Now if I go to the settings on the router it sees the GoFlex but there are no folders showing even after I entered a 'media sharing' one via PC. I've rebooted the router,the PC,the drive,nada. I reformatted to NTFS and nothing. Why the heck does this router refuse to see this drive? I even when connected to the PC made sure the sleep timer was set to 'never' so it wouldn't sleep on me.
View 9 Replies
ADVERTISEMENT
Jun 25, 2012
Bought GoFlex Home 3TB, plugged into Cisco WRT310N V2, w/ Desktop PC (Win 7 64bit) does not recognize the drive. Get NETWORK ERROR "Windows cannot access \goflex_home" Error Code: 0x80070035. Can not map netork drive. Under Win Explorer the drive DOES appear as "GoFlex Home:UPNP-AV" in TWO places, 1) under Media Devices & 2) Under Storage. Bother places are treated as MEDIA because, when I click on either of them it opens Windows Media Player! I can type in the IP address in BOTH IE & WIn Explorer and it will take me to the web page for the drive, where i can log in and create users, add folderes, etc. I WANT TO USE THIS AS A BACK-UP DRIVE, but can't get WINDOWS TO RECOGNIZE IT. I have turned off McAfee
View 3 Replies
View Related
Jul 10, 2010
I have my router setup fine to the internet, as well as the media server. I can't figure out how to access the hard drive from my laptop, however. The manual says put 192.168.1.1 in the address field of windows explorer, but it just gives me the "Setup" page for the router.
View 9 Replies
View Related
Jul 31, 2012
I recently copied files to my hard drive that was connected directly to my computer (via USB).When I connected the disk back to E3000 the files were missing. I connected it back to PC directly and verified the files are there.My PC runs Windows 7 Enterprise.Why can't I see files copied via local connection when I connect the disk to E3000.I carefully compared the permissions with files that I can see just fine and there is no difference - same permissions, same owner.I also get all kinds of permission errors when I try to delete a files from the network drive.
View 9 Replies
View Related
Sep 26, 2012
I currently have a E3000 router. I have set up a shared USB drive successfully through this router. After a couple of months, I needed to re-locate my router into a different room. After doing so, I plug back in the USB drive and cannot access it. If I go through the GUI, it tells me that the drive type is not supported, and if I just plug it into a computer to obtain the infromation off of it, I get a "drive is corrupted" error
View 5 Replies
View Related
Jul 30, 2012
I have a E3000 and just upgraded my Mac with the OS X Mountain Lion. I can't access my external HD anymore, although when I go to the router set up, on the storage tab, the router appears to recognize the HD.
View 9 Replies
View Related
Feb 23, 2012
I recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 1 Replies
View Related
Sep 15, 2010
I recently purchased a Linksys e3000 router. Everything is going great except that both my desktop (Windows 7 Machine) and Laptop (Macbook Pro) keep losing the connection to a DLINK 323 Nas drive I have plugged into the router. This is problematic because I keep my itunes library on the NAS drive.
View 2 Replies
View Related
May 5, 2011
I correct in understanding that when an external hd is connected to the e3000 via usb, that i can read and write to it, but i cannot delete files from the external drive? i have been trying to figure this out for a while and cannot delete files after i write them.
View 3 Replies
View Related
Jan 15, 2012
I have a E3000 with a USB hard drive plugged into it. It works perfectly as a shared storage drive from all my computers. But as a Media Server it is not working. I purchased a Sony SMP-N200 Steaming Media Server that found all the PCs in the house and can stream music and photos fine. It does not see the shared USB drive connected to the E3000. Sony's web site says it uses DLNA to find and stream music and photos. It says Windows 7 is one example of DLNA When I go to DLNA.org and check to see what routers are DLNA compliant, it says the Cisco E4200 and E4200v2 is. Is Cisco going to make a firmeware upgrade to include DLNA for the E3000?
View 6 Replies
View Related
Jan 1, 2011
I just installed this router and connected the hard drive (Western Digital 1TB) which worked fine at first. When I moved some movie files to another folder they lost all of their data. The file names are still present, but all the media files show zero bytes and are no longer usable. Is there anyway to get these files back? I have been digitizing all our movies to the tune of about 90GB. What could be going on here? I disconnected the HD from the router and plugged directly into the laptop. Still shows the file names, but each file is still at zero bytes. Not a cool way to have a media server for your house!
View 6 Replies
View Related
Jul 22, 2012
I bought a seagate USB hard drive today from Target. Its a 2TB and I was going to use it via USB attached to my router. I connected it and the Linksys firmware detected it and I was able to create the appropriate folders on the drive for storage through the linksys GUI.My issue is that I am now trying to move my movies and tv shows over to the drive and it isn't allowing me to do that.
I get an error message that says "You don't have access to //myshare. contact your administrator".
I'm not sure why I was able to create folders on this drive but am unable to move files to it. Makes no sense to me. Write permission is write permission no?My machine which currently stores the media files is windows7 utimate. The router is E3000 using up to date stock firmware.
View 1 Replies
View Related
Jan 7, 2011
If I try to set a torrent download to write directly to the USB drive on my E3000, it only works for a few minutes (at low speeds) and then I lose access to the drive and the torrent stops. I can access the drive again less than a minute afterwards.
It'd be handy to be able to write torrents straight to the USB drive instead of having to move the completed files to it after the torrent is finished.
View 5 Replies
View Related
Nov 30, 2012
For the past few months, I have been using a Buffalo drive (formatted as FAT) as a media server to function as my network drive for iTunes. Unfortunately, I have recently noted in the last 2-3 weeks that, when copying new files, the file size changes to zero bytes. I do not seem to have this problem when i plug the drive directly into my computer via USB, only when adding files over the network. I spoke to tech support, who said, based on the story in that files can be correctly transferred when directly connected, it appears to be a network problem.
I am running OS 10.8 with iTunes 11 (but also occurred with iTunes 10) and using version 1.0.04 on the E3000.
View 1 Replies
View Related
Jun 14, 2011
I needed the Guest access of wi-fi setup that LinkSysys routers provided. I don't need the router/modem i just want to have wi-fi access point. I'm an advanced user and i can work with manual setup etc.I tried to do a manual setup of the router, i changed the IP address to mask my network and enable wi-fi and worked BUT the guest access option is NOT available unless you use the stupid CISCO connect software.
Now the cisco connect software IS NOT working or complete the setup if you don't connect it through the router and gain Internet access which is IMPOSSIBLE for me to accomplish as my modem is connected to a firewall device and we are using static DSL options with PPPoE and usernameme/password. There is no way i can get cisco connect to load properly as it always "fixes my connection trying to gain Internet access".Is there any solution on manually properly setup this router and take full advantages of it capabilities or should i return it ?
View 7 Replies
View Related
Dec 29, 2011
Segregate Model STAA1500100 works fine in USB Port of computer but Cisco Connect does not recognize the drive when connected to USB Port on Router. Drive does low beep beep every few seconds. The Router firmware is 1.0.03 build 14.
View 5 Replies
View Related
Jan 31, 2012
Work connection will load database about a third of the way then crash laptop. I can change out the router from the new Cisco e3000 to an old wireless router and it works fine.
View 9 Replies
View Related
May 4, 2011
when an external hd is connected to the e3000 via usb, that i can read and write to it, but i cannot delete files from the external drive? i have been trying to figure this out for a while and cannot delete files after i write them.
View 3 Replies
View Related
Jan 2, 2012
Purchased desktop from micropro in 2002. We finally upgraded to cable internet in 2011, Wife purchased Think Pad laptop also in 2011 (wireless enabled). Purchased Belkin wireless router and want to network these 2 computers.1. My desktop has been demoted to the garage. I have wiped it clean (i hope) by doing a reinstall of XP Pro. Now some of the USP ports won't work. How do I network these two machines?
View 1 Replies
View Related
Mar 30, 2012
I've read the various threads on here and tried all the fixes suggested and I still cannot get my PS3 to "see" the USB drive I've attached to my router.I can see it and access the files from a connected computer, but not the PS3.I've tried creating a share with one directory and sharing the entire partition with no luck. I've enabled all the FTP options with no luck. UPNP is enabled. I've tried setting up the guest account with no luck.I've tried restarting, unplugging with no luck either. I also went into the USB drive and reformatted and started all over again.My PS3 can easily see the other computers on the network, but I would like to use the USB port on the router to not have to have a computer running to stream music.Is there another menu location on the PS3 I should be using to locate the USB? Currently I just look under music or video and the other computers are there. Just not the USB.
View 1 Replies
View Related
Apr 22, 2012
I have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
Primary Access point 192.168.0.1
DCHP server with reserved IP addresses for server and PC's and smartphones
Port Forwarding Set for Server at 0.004 : 80
Port Forwarding Set for E3000 at 0.002 :21
Secondary (E3000) router 192.168.0.2
DCHP server is disabled
Port Forwarding is Not being used
connected to primary router LAN port 1 by LAN port 1 on E3000
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?
View 2 Replies
View Related
Jun 29, 2011
I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.
View 9 Replies
View Related
Jul 4, 2012
Since the upgrade by Cisco I can only see Win7 PC's on the network. I can not see the USB drive attached to the E4500, nor can I see my Media server which is Linux based nor any Win XP computuers.
View 9 Replies
View Related
Sep 8, 2012
i have a 2tb seagate expansion formatted ntfs. i am primarily a linux (ubuntu) user, but when the drive drops off, it cannot be seen in any os and it doesn't show up on the router setup page.
View 6 Replies
View Related
Feb 8, 2013
I picked up an EA4500 about a month ago and so far it works great! I would like to purchase a USB hard drive to plug into it, but noticed the officially supported drive list on the support site seems to be a little out of date. good "current generation" USB hard drive that works with this router?
View 5 Replies
View Related
Feb 3, 2012
Im having trouble with my E3200. The router is working fine in all areas, with the exception that I cannot get my PS3 to detect the shared USB drive that is connected to the router. The drive is detected /mapped on the connected Windows desktop, but files/folder/drive is not appearing on PS3. The PS3 is connecting successfully to the router, as I have a strong internet connection. I believed that the E3200 would be able to share the USB drive with my PS3 for media file streaming... Or have I not done something correctly in the settings?
View 3 Replies
View Related
Mar 12, 2012
I just purchased an E4200, primarily to connect my Free Agent drive to for network access. The router has V. 2.0.36 installed, drive is fully shared, but I am unable to see the drive when I attempt to map it on any of my XP laptops. When I perform discovery, it finds the router, but is unable to see the drive.
View 2 Replies
View Related
Dec 11, 2012
I just got a new E4500 and plugged a blank 2TB drive into it (Windows shows it is formatted NTFS) which was originally plugged into my WRT-610. I'm moving my media files and when it hits a 50+GB video it reports that there is not enough space to move the file. Smaller files are moving just fine.
View 4 Replies
View Related
Mar 6, 2013
I had a Sony 8gb usb drive plugged in and was working great with my smart tv and computer..... over last weekend i unplugged the drive and had to format it to my xbox moved what i need to and hen i formatted it back to ntfs the router wont recognize the usb drive. during this i also was facing this bad gateway error 502...i downgraded my router and now using the classic but i still get a non recognizable device error.
View 1 Replies
View Related
Apr 15, 2012
What do I have to do to be able to access the USB drive I plugged into my WRT610N from anywhere, on any computer?
Currently, I just plugged it in, went to \WRT610N in windows explorer, and mapped it as a network drive, adding a few files to try out.
So what do I need to do now to access it from any computer that has internet?
View 1 Replies
View Related
Feb 7, 2013
I just got an EA4500 and I really like it. I set it up with my printer, tested a few things and everything is working perfectly fine. The problem I'm having now is that when I plug a flashdrive to the USB I don't know how to access it. For some reason when I go to the settings under USB Storage it says "There is no drive in the USB Port". It tells me to click refresh but that doesn't seem to work.
I'm running firmware version 2.1.39.145204
View 3 Replies
View Related
Apr 2, 2012
I have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
View 9 Replies
View Related
Jul 11, 2011
How do you set up the E3000 for ATT u-verse?
View 2 Replies
View Related
