Linksys Wireless Router :: E1200 Port Forwarding To Wireless?
Feb 23, 2013
I have a camera connected to the router. IP address 192.168.1.145(static). It responds on port 7654. The camera connected either wired(if connected) or wireless otherwise using the same IP and port. the camera responds correctly on both wired and wireless from a LAN connected computer. If I try to connected via the Internet, camera will only respond if connected via a wire; i.e. the port forwarding is not forwarding internet requests on port 7654 to a wirless IP address, but will to a wired IP address. It has worked in the past, so the router seems to be capable of routing requests to the wireless LAN. Either I have changed some setting (unlikely as have reloaded saved configuration) or it is a hardware error in the router. Have had previous problems with the router which neccessitated a full reboot/reset to clear. Guessing there was some problem making the router run out of memory. Response to the configuration setup pages can be slow, and some (DHCP list and access policy) on occasions are just not responded to(AP) or not complete(DHCP - page opened but no data shown)
View 9 Replies
ADVERTISEMENT
Sep 6, 2012
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Linksys E1200 Router not saving Port Forwarding changes.I have tried:
-Restarting the Modem
-Restarting the browser
-Restarting the computer
-Tried to Port Forward through both the Single and Ranged Port Forwarding
View 9 Replies
View Related
Jan 2, 2013
I set up port forwarding on my router. When I go to canyouseeme.org and put in my public IP address (I can ping the IP address with no issues) and the port that I'm forwarding it says it can't hit the port.
View 2 Replies
View Related
Oct 17, 2011
I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.
View 1 Replies
View Related
Aug 21, 2011
I have configured port range forwarding (8440 - 8449) for a single PC (192.168.1.134) and am unable to access these ports from outside my LAN. Conversely, if I set up single port forwarding for each of the ports in the range for the same computer then I am able to access from outside my LAN. Does port range forwarding actually work?
E1200 / 1.0.00 build 11 Jan 23, 2011
View 1 Replies
View Related
Sep 19, 2011
I have a question about the function of an E1200 relative to a WRT54G. We currently have the 54G plugged into our LAN, the Ethernet cable plugged into one of the Ethernet ports, not the Internet port, on the back. It is giving wireless clients IP addresses according to our main LAN DHCP, as if they were hard-wired which is correct. Bad thing is, I have no idea what IP address is/was assigned to the 54G itself as it was not logged when done, way before my time. I cannot log into it and take a look at its settings and attempt to mimic what is going on in there on something like an E1200.
Therin lies my next questions. What could be occurring on the 54G that is enabling it to dish out like a WAP and does the E1200 support WAP function? If not, which models do that can be added to the 54G?
View 8 Replies
View Related
Apr 22, 2013
I'm trying to set up a minecraft server i have the correct ipv4 adress and port but for some reason its still closed?
View 7 Replies
View Related
Jun 26, 2012
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies
View Related
Feb 26, 2013
I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
View 9 Replies
View Related
Sep 16, 2011
I'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
View 5 Replies
View Related
Nov 2, 2012
I am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.
View 9 Replies
View Related
Nov 2, 2012
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
View 3 Replies
View Related
Feb 6, 2013
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
View 2 Replies
View Related
Nov 1, 2009
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
View 9 Replies
View Related
Aug 31, 2012
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
View 1 Replies
View Related
Jan 19, 2012
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
View 1 Replies
View Related
Jan 28, 2012
I recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
View 2 Replies
View Related
Mar 30, 2013
I'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
View 3 Replies
View Related
Nov 14, 2012
Im going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable
View 1 Replies
View Related
Feb 12, 2012
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies
View Related
Aug 18, 2012
I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
View 9 Replies
View Related
Oct 31, 2011
Im trying to open up some ports on my e3000 for the use of Teamspeak and my Teamspeak server. However when i get of the information filled into the single port forwarding under the Gaming & Applications tab, and click save settings. The page just refreshes, with none of the changes being saved.
View 6 Replies
View Related
Apr 2, 2012
IPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
View 7 Replies
View Related
Nov 30, 2012
I upgraded to a 6500 from a e4200. I use ports 81-84 on test web servers set to static Ip,s when I open the ports nothing can get through from the outside. I can hit the pages internally on those ports and IP's but not from my external ip to those ports. When I set my old router everything is fine.
View 9 Replies
View Related
Mar 5, 2010
How to forward a single port to a different port to a specific computer for the WRV210 router?
I would like to forward port 10100 to port 25 to my mail server. There are times when our people are at a hotel and they block port 25 and I have done this in the past on a BEFSR11 and BEFSR41 router. There does not seem to be a Single Port Forwarding setup page and the Port Forwarding setup page only allows you to forward a range to a specific computer, it does not give you a different port you can assign an incoming port to.
I have the most current firmware revision, 2.0.0.11, and Hardware Version WRTR-221G_V01.
View 3 Replies
View Related
Aug 12, 2012
I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit.
View 1 Replies
View Related
Aug 19, 2011
I have an E3000 with firnware 1.0.04. A forwarded port is spontaneously changing the IP address assigned to it, but with no change indicated in the singel port forwarding configuration.I have a web server on IP=XXX.XXX.XXX.7, and another device on my LAN with an internal web server at IP= XXX.XXX.XXX.8. The single port forwarding configuration is:
HTTP, external port 80, internal port 80, protocol=TCP, to internal IP address xxx.xxx.xxx.7, enable checked The configuration is saved, and all works well for for hours and/or days and I can use the web host from the intenet as expected. However, after a few days or hours the E3000 suddenly starts sending the http traffic to IP=xxx.xxx.xxx.8 instead of xxx.xxx.xxx.7. When I log in to the router and look at the port forwarding page, it still says it's forwarding the http traffic to xxx.xxx.xx.7 ~ even though all http traffic is being sent to xxx.xxx.xxx.8! I have to reboot the router to get the port forwarding to work properly. If I leave the device at xxx.xxx.xxx.8 powered off, the router seems to work fine for extended periods.
There are no port forwarding services in the router that reference IP=xxx.xxx.xxx.8 , and it does not appear that the port forwarding problem is related to DHCP. All devices on my network have a reserved DHCP address based on their MAC. It does not appear that the spontaneous port forwarding change occurs when when the xxx.xxx.xxx.8 device powers up and gets it's address via DHCP. I have also deleted the xxx.xxx.xxx.8 device from the DHCP reservation table and simply access the device as needed by referencing it's IP, and xxx.xxx.xxx.8 is outside the range of DHCP assigned addresses, and the spontaneous port redirection still occurs once in a while.Is there a known bug where forwarded ports are sent to the wrong IP address?
View 5 Replies
View Related
Jun 18, 2012
I just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.
View 9 Replies
View Related
Oct 19, 2012
i have a WRT160N V3 and DMZ or Portforwarding dont work.i tried locally following
WAN_PC-> WAN-PORT -> WRT160N V3 -> LOCAL-PORT -> LOCAL_PC
The WAN_PC has a Static-IP 192.168.1.2, Subnet 255.255.255.0
The WAN-PORT has a Static-IP 192.168.1.1, Subnet 255.255.255.0
ON the WRT160N V3 i configured a DMZ on 192.168.0.100.and Disabled the Firewall.
On the LOCAL_PC (192.168.0.100:8888) is a Apache
So when i type 192.168.1.1:8888 on the WAN_PC i get NOOO Website from the Apache on 192.168.0.100:8888?
View 2 Replies
View Related
Sep 10, 2012
When I try to set a port for forwarding and set the IP address to forward to:192.168.1.108 (of course, I only type in that last number, 108)I get an error message that the number must be between 1 and 65535. It is! Why am I getting this error message?
View 5 Replies
View Related
Jun 10, 2011
I recently purchased a Slingbox PRO-HD and the iPad software to view HD on my iPad when I'm away from home. When I setup the Slingbox using their web-based configuration program, it reports that I do not have my network configured for the best performance for internet viewing, which is what I need for the iPad. I suspect that I don't have port forwarding for port 5001 correctly setup on my system. I can successfully connect to my Slingbox away from home on my iPad and my laptop, but the performance is indeed poor.
I have a cable modem and two E2000 routers. The first E2000 is connected to my cable modem in my home office and the second E2000 is in my home theater. I used Cisco Connect on separate PCs to setup the two routers. Here are the details:Cable modem:Scientific AtlantaModel DPX2203 SeriesPart number 4006351'Ethernet' connected to Router 1 'Internet' connection.
Router 1:Cisco LinksysModel E2000IP address 192.168.1.1Wireless enabled.'Internet' connected to Cable modem.'Ethernet' connections:1. Seagate network storage drive2. Desktop PC3. Desktop PC4. Router 2
Router 2:Cisco LinksysModel E2000IP address 192.168.2.1Wireless enabled'Internet' connected to Router 1 'Ethernet 4' connection.'Ethernet' connections:1. Slingbox PRO-HD2. Desktop PC3. A/V Receiver4. Blu-ray player
How do I setup port forwarding for the Slingbox PRO-HD on port 5001? Also, what is the best way to setup two E2000 routers so that I can use both as wireless access points?
View 5 Replies
View Related
Oct 16, 2012
I have a Cisco E4200 with a Thecus NAS behind it. I configured port forwarding on port 80, 1080 and 4433 to access the NAS. However it's not working. Also tried to place the NAS in DMZ, but also I cannot connect it from outside my network. Inside my network, there is no problem.I also connected the NAS directly to the internet, and then I can access it from outside my network.I already tried a factory reset, disabled UPnP and IPv6, but nothing seems to work. I also replaced the router with a Cisco E3200, but it makes no difference.
View 9 Replies
View Related
Dec 12, 2011
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.
View 4 Replies
View Related
