I upgraded my E2500 with the last version of firmware but now is dead. the power led is turn on, but the ping are discontinued. the other problem is that after 10/15 sec, the router will restart automatically. i try with tftp but after the reset of router does not change anything.
View 5 RepliesHave to re-boot 1-2x daily. Updated firmware through Cisco, followed by about 7-8 support calls. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case). When E1500 goes down, all wired and wireless connections are lost. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case).
View 4 Replies View RelatedHow do I troubleshoot to find out if my wireless router is dead? I have a WRT160N. It's been giving me problems lately, so I thought I'd update the firmware. Long story short, I had to reset it, but I still can't get into it. I have gotten into it, but when I try to save it gets hung and then I reload and then it starts all over again.It does work hard- wired--I can access the internet with ethernet. But I can't get the dang thing reset and then upgrade the firmware...
Somehow I set this router up to act essentially as a repeater, an extension of the wireless network that is "anchored" (not the right word I'm sure) by the wireless router provided to me by my DSL provider. I want to do the same thing once I get this one working again--set it up as an extension of the existing network so I can essentially walk around the house with my iPad and not have to re-log in when passing into a new "zone".
I've got an IPTV network with Bell FibeTV with Motorola VIP1216 (the DVR master) and VIP1200 (slave) cable boxes. All the coax cables in my walls form a wired ethernet network instead of a cable TV network. To get better wireless coverage in my home, I've set up routers as wireless access points at each of the cable boxes. Essentially I've plugged the router into the ethernet bridge of the cable boxes, and disabled DHCP and gave it a static IP and did all things I needed to do to disable all the routing capabilities and make it into a switch (here's what I did, step by step: [url...]). So when I go from one room to another, I just select a new wireless access point to get maximum signal strength and speed.
View 6 Replies View RelatedIt has happen suddenly : Internet is not working through WRT150N, though it work when directly connected to the modem. So I think it is a router issue :On the WRT150N, Internet light is flashing fast for 2 seconds, then is off for 2 seconds, then flashes, then is off and so on, wether there is a device (computer, modem, ...) plugged or not, through the blue ethernet connector.And sometimes, Internet light stays off from power on, whatever is done with ethernet connexions (yellow or blue).
When connected to the blue ethernet Internet connector, my pc ethernet lights don't blink (nor the link light or the data light)I have try the 30-30-30 reset cycle. But it doesn't improve.I have tried the loopback test : connect an ethernet cable from the one of yellow ethernet port of WRT150N to the blue ethernet of WRT150 N.Sometimes, the light for the yellow ethernet port goes on for a few seconds, while the Internet light continues to flash. After a few seconds, both go off.Sometimes, as soon as the loopback is made, the 2 lights go off, and if a computer is plugged to the yellow port, the ethernet lights of the computer and the router stays off.But I can access to WRT150N through Wifi and I can access to the web management.
I've bought my E4200v2 via eBay, because original Cisco store doesn't ship to my country (Israel).My first unit was... defective, I think I wrote about the issue on this forum a while ago.It had connection troubles, always in a dead loop, saying "Connecting..." one to 100 times it managed to connect, and suffered slow internet connection speed, where all speedtests gave me 60% of my actual internet speed.Which is 30mbit.I'm sure about my ISP, it uses next.gen technology, they have their own underwater optic cables. Without Cisco router, only dialer, I get 100% of my internet speed, or with another router as well.I decided to RMA my e4200v2.
Out of context question: Why there's no option to specify server name instead of server IP? our ISP uses domain name for connection, rather than IP address, as they have a lot and a load balancer above 'em.Now, to the original issue.Refund is no option, RMA again is no option, too much time and money.Maybe there is a solution? It just can't be the reality, that two out of two units are not working. I heard this router is very good. And I heard the v1 is working very well in Israel. so It can't be our country that is the problem.By the way, I've called my ISP and they've switched me to MPLS connection for a try, so in a router you just switch to "Automatic configuration - DHCP" and it pulls IP, DNS servers and connected to the internet, but was hooooribly slow.
So I'm back to dialer. the main still is the "Connecting..." loop, sometimes says "Connected" for a second, and then connecting again... It manages to pull DNS addresses though, but never the IP and never managed to stay connected.All the connection configs are very basic, you know it. Server IP, username, password, keep-alive, MTU (I've tried auto, and a ton of other combinations recommented by our ISP or Cisco).My latest idea was to film how I burn it or throw a rock at it and send to Cisco the video, but that's kinda too much, it's too early for such decisions, especially when already $300 were spent.
i brought a new wrt120n from the retailer and when i tried to connect the modem and configure, my phone gets dead and i couldnt connect it to the internet.
View 1 Replies View RelatedWRT400N worked great for 18 months.
Last week the Verizon-supplied DSL modem went bad (wasn't receiving data) and was replaced.
Now I can get Internet direct out of modem, and when I connect it to router the router's Internet light is on, but it seems to stop there. Devices connected to router via Ethernet or wifi don't get Internet.
I'm able to get to the router's admin console via Ethernet and wifi, but no Internet.
In a lab environment, I have a stack of two 3750v2-48ts switches. I upgraded the stack from 15.0(1)SE2 to 15.0(1)SE3 using archive download-sw.
Switch 1 in the stack reloaded and came back with the new image.
Switch 2 appears to be dead. No console out put. When power is applied, the SYST LED blinks 22 times, then stops. I've held in the mode button for up to 60 seconds, held in mode while applying power, removed the stack cables and repeated...there's not a whole lot else I can think of to do at this point.
I have just ugraded to a E3000 from a wrg54 to increase the rang, but am still having dead spots. How to increase the range.
View 1 Replies View RelatedSo let me start by saying that i'm stupid, as i did not 1st read the manual properly and thus upgraded my camera WIRELESS.. (when manual clearly states by cable ONLY).
Camera is now DEAD. Only red led light is flashing.
Hardreboot not working (pushing reset, then switching on camera & hold reset for 30 secs)
Is there anything else that i can do myself or is this gonna be a repair job?
My router appears dead. I assume that I need to reset it and replace the firmware.
View 3 Replies View RelatedI'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies View RelatedI previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
Just for no reason that I know of the wireless stopped working. I can can connect to the SSID fine and there seems to be good signal strength, but no wireless internet access.
I have up to date February 15, 2011 firmware, 205NA, hardware version = B1.I have done a reset with no luck.I have done a 30/30/30 factory reset = no luck
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies View Relatedi buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies View RelatedI want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies View RelatedHow To Reset E2500 Router
View 1 Replies View RelatedI am trying to setup a WAP with my linksys 2500. I am currently using a Gateway connected to my DSL and am looking to set up the access point through the E2500.
View 1 Replies View RelatedSo, i have a e2500 router and find that every so often, I have to unplug it and reset it because I am losing my internet connection.
View 7 Replies View RelatedHow to set router to use as Slind Box Pro?
View 3 Replies View RelatedI currently have my E2500 connected via wired LAN (not WAN) port on another router. The E2500 has an LAN IP of 10.0.0.2 and the router has 10.0.0.1 and a dhcp range outside of these. DHCP is disabled on the E2500. I can use my E2500 as a wired access point with no difficulty I plug something in and it calls the router and gets an address, but I can not get DHCP through the wireless of the E2500.
View 2 Replies View RelatedI have Time Warner as my internet company. I recently purchased a new Linksys Router Mode E2500 because I have been having issues with my old router. My internet was disconnecting sporadically. After connecting the new router, a started getting the same issue. I replaced my internet cable modem to a Cisco 2100 modem (provided by Time Warner). I noticed that the issue keeps happening sporadically which makes me believe it is my Linksys router. Every time a new wireless connection is connected, my modem circuit dies. This happens sporadically.
View 4 Replies View RelatedI have bought and installed an E2500 router 4 days ago. Installation of router and network using Cisco Connect was easy and without problems. However, after 4 days of usage, not changing anything in the network nor running Cisco Connect or accessing the web interface, I tried to start Cisco Connect and got the message "Cannot access your router".Internet is running, router is accessible via 192.168.1.1 in a browser window, Cisco Connect also works fine on my laptop.The only solution I found on this forum is: reset your router and reinstall Cisco Connect.and then every 4 days resetting my router and reinstalling the software?
View 4 Replies View RelatedMy network consists of a Westel C90-610030-06 DSL modem, Cisco E2500 router and Hawking HWREN100 range extender.My wife has trouble with her IPad connecting to the Hawking.Apple says I need to Disable WMM on the E2500.
View 2 Replies View RelatedI am working with vpn setups for the first time. I would like to be able to connect to a computer on a home network through a linksys E2500 router. I have found alot of documentation on connecting to an external vpn from a computer on the lan side of the router, but nothing on connecting from the outside in. The router does have a static ip address with my internet provider, so I can contact the router from the outside. But makeing the connection to the computer on the other side of the router is where I am missing something or I dont realize that it is not possible. On the LAN side I am using DHCP to assign the address to the computer I want to connect to. Perhaps I need to make it have a static address also? I realize that when I configure the connection from the outside that I need to direct the connection to the remote computer in some way, unless vpn connections are fully passed through the router and the connection issue I am having is with the "inside" computer.
View 2 Replies View RelatedGot a problem with my new Linksys E2500 router. I have a Huawei Smart Ax MT882 cable modem, that connects to my desktop through an Ethernet cable, it works fine.
Recently i bought a notebook and i thought i could have a wireless connection, using the modem as well... So I bought a E2500 router, that is connected with Ethernet cables to the desktop and the Smart Ax MT882 modem.
It happens that i am not able to setup the configurations to make this work (This router does not supported by my ISP provider).
I have an E2500 configured inside my network. It is configured to give wireless PCs (This subnet is connected to a Lan port with 10.30.0.0 address) another subnet than wired PCs (this subnet is connected to Wan port 192.168.0.0). Since i configured i can access from wireless PCs to servers and PCs in the wired subnet but cannot access from wired computers from to wireless PCs. I suppouse it is because traffic is restricted from Wan to Lan.
View 5 Replies View RelatedI have a E2500 connected via LAN to my network via a switch or hub through a sonic wall and into the modem out to the internet. The problem is that I am only getting +/- 5Mpbs Down and +/-7 Mbps up through the router.
If I connect my computer to the network with out going through the router my speeds are more in the range of +/-28 Mbps down and 16Mbps up. I have been working with Linksys support but they have not been able to assist me with this yet! Is there any configuring I should be doing at the firewall or to the router to tell it to open up the port for faster speeds?
I just bought a linksys wireless n dual band router e2500 and i want to make my old wrt54g router as an access point. how do i do this and where to start?
View 11 Replies View RelatedI just installed the E2500 wireless router, and it works great for all devices we've tried so far. Here's the thing: we have a laptop that has been humming perfectly along for more that 12 years because we have never let it be touched by the internet. It has built in wi-fi, but we've never connected it. It has no viruses, no Microsoft creep, we've never had to purchase a virus software update and it has outlasted every piece of computer equipment we've ever owned. We'd like to keep it that way!
But now that the wireless printer is working beautifully, we want to know if there's a way to send the laptop through the router to the wireless printer, but not expose it to the internet. Is that possible?
how to update Cisco FIrmware ... it is like brick....no responce from router.. i have tried With Linksys TFTP,, just coppying successful and not working..
View 1 Replies View Related