Linksys Wireless Router :: E2500 Stops Receiving Data For Any Large Download
May 3, 2011
My setup is as follows:
Linksys E2500 as DHCP client, all default network settings (MTU auto configured to 1500), connected to:
ZTE 831 II ADSL2+ modem in bridged mode
The issue is that whenever any large file is downloaded over HTTP, the download stops after about 4 minutes and never resumes. This results in:
1) HTTP downloads of anything > ~80 MB failing; tried using several browsers and CURL, all with the same results
2) iOS downloads in iTunes timing out
3) YouTube videos stalling every few minutes
Interestingly, Netflix streaming works OK. Perhaps that's because the protocol for Netflix is not a single large download but a bunch of smaller ones, but that's conjecture.
This all occurs over both wireless and wired connections to the E2500.
If I connect my Mac directly to the ZTE modem, I don't have the problem.
View 8 Replies
ADVERTISEMENT
Feb 12, 2012
Bought a E2500 Linksys Router, i updated with Firmware Version 1.0.03 ( Build 4 )no problem,!! it is connected directly with a RJ45 Cable, router to Computer,no firewall on at all ,wide open yes i am on internet !! but here is the Problem i get everytime !! ---> ( Cisco Connect Setup Software For PC ) what it does is that it installs agreements etc.. password and all but near the end it tells me i am not on the internet you have been disconnected ! ;( and stops everything from continuing installation and i have to uninstall all from registry etc.. then re-install again and get same problem everytime i got a e3000 and it is great.
View 1 Replies
View Related
Jul 4, 2012
We use our internet to watch Netflix. We have had no problems until recently, I called the satellite Internet company(which is a local co.) they told me my router was going out. I bought a new one, problem solved! Right?!? WRONG my husband told me my neighbor just got Internet and has been playing Xbox everyday which coincidently is between the 5:30pm to 10ish pm we have been having issues with our router. What can we do to fix this? Do I have to buy a bigger router? He is not stealing off mine because it is password protected that was changed when new router was setup and programmed. I have been running of a Cisco Linksys E2500 advanced dual band n router. The router is in the same room as the TV accessing it, which we previously had no issue connecting anywhere in the house or garage.
View 1 Replies
View Related
Oct 6, 2012
For my network the way it is setup is one building has the 2 main servers.simple wireless router and a few laptop that connect to it. a Wii and some other devices, all of them share media etc with no issue. Internet is not a problem either.One of the servers has a PCI wireless card and connects to another network.(network2)network 2 is able to share and play all the media off the service lets say 80% of the time.It also has a different internet provider and internet connection is not a problem but the wireless signal strength is low , (2 bars) or -55 to -82 it seams to jump around at.If you try to stream or play too much media it freezes on you. or if 2 devices on network 2 try to play something it freezes as well sometimes though when the signal is good -55 ish there is no issues.There is alot of wireless traffic in the area, i cant change that.and dont really want to buy a ranger extender or something $20 is what I have for parts if anything. If I were to put a 2nd wireless card in server 2 or Server 1 even. Also both the wireless router on network 2 and the pci card on server 2 are physically as close as hey can get.
View 6 Replies
View Related
Dec 6, 2011
We are receiving a large amount of output drops on 4 interfaces that connect to microwave wireless.This is playing up with our Management system. Saw a bug report but that was for 3750, not the IOS version but was a similar issue. [code] The output errors tend to happen at the same time. All ports are trunks however there are other trunks on the switch that are not having these issues. [code]
View 7 Replies
View Related
Aug 8, 2012
Cisco ASA 5510. Between 5 to 10 minutes of reseting the asa traffic stop accessing outside ip addresses. Ping from console fails to ISP router IP. Ping to google name server failes. I have reset to factory default only setting up nic and natting and it still happens.
View 2 Replies
View Related
Nov 7, 2011
i have a problm in Epson LQ-2090 Dot Matrix Printer that is LAN Not receiving the data's .....Last time the same prblm came so i installed IP Add thn after 10day's again the same prblm repeating..... So can any one tel me the reason y it happen..... But i think LAN Memory power is gone.
View 1 Replies
View Related
Oct 26, 2012
I'm using Cisco 2100 cable modem. It worked fine until some time later where the Data Send & Receive LED's stopped blinking. A man came to check if the cable was the problem by replacing it, but it wasn't. He claims it might be related to the laptop. I have tried several times restarting it. (I'm using mobile broadband) I would really like fast rather than slow internet ( I was limited so now it's slow but free)
View 14 Replies
View Related
Aug 6, 2011
Everything is fine except that whenever I am receiving packets, there is a corresponding upstream of packets which is subsequently slowing my download speed.I should be getting ~600kbps, but I am instead getting ~200kbps.The ratio of packets sent/received is almost 1:1.5, and of course when your upload bandwidth is being maxed it starts cutting your download speed.
View 3 Replies
View Related
Oct 20, 2011
I'm looking for some software for copying large amounts of data from a Mac OS X machine to a Windows 7 machine over a Cat5e cable with IPv4 connectivity?
Another way I could ask this question is what IPv4 protocol will have the lowest overhead so that I may copy large amounts of data the fastest?
Also, would that mean it's a low-level protocol, like transport layer?
View 1 Replies
View Related
May 8, 2011
E3000 can see only 1TB Maximum. I have a 3TB WD storage and E3000. I have upgraded also to latest E3000 firmware version.
View 3 Replies
View Related
Aug 9, 2012
I got a refurbished EA4500 (directly from Cisco) last week. I have been having a few issues, which I have found (not too great) workarounds for. However, the latest issue has me stumped, and is unacceptable.Whenever I am transferring files between 2 computers, I get kind of OK speed (5 MB/s). However, while this transfer happens, no other device can connect to the net. Actually, even trying to go to router home page (192.168.1.1) times out.The clients still say they are connected to the router, but I just can't get anywhere.As soon as the file transfer finishes, everything goes back to normal.EA4500 replaced a WRT54G. Never had any problems with that router. It was such a workhorse. Just needed to upgrade to a n-router.I am on the latest non-cloud firmware.I have reduced the MTU size to 1200. Not sure that matters.
View 9 Replies
View Related
Mar 28, 2012
My WRT610N media server is not serving up large, MKV files (>1GB). I have a 500 GB Maxtor connected with external power.The media server serves smaller files just fine (although they are not MKV files). The disk is formatted as NTFS. I can access the large, MKV files via mapping network drive, so I know they are present on the disk and they are intact; but they media server does not show them.
View 1 Replies
View Related
Nov 20, 2012
we are currently using a modem router LINKSYS WAG120N Wireless-N ADSL Router but are not satisfied. lots of dead zones and I think that there are too many users for this AP. last count gave around 20 users. so I'm looking for a solution to be able to handle 20+ concurrent connections and with large coverage - 600 m² .
View 7 Replies
View Related
Sep 18, 2011
On the main floor I have a Linksys E3000, hooked up to my ADSL modem along with laptop #1 which has all my video and photos on Picasa. Laptop is on 5ghz, running speed at 300. I'm running the E3000 in dual mode (running 2.4ghz and 5ghz at the same time.) I have 2 different network names mjames5gz and mjames24gz.
In my basement, I have a laptop running on 5ghz and an IP camera running 2.4 ghz. the signal in the basement is on the low side for both. Under Wireless network connection, I am getting around 100 on Speed vs.300 on the laptop.... The basement is fully finished so I can't run cables to the basement easily. What could I buy so I can stream videos from laptop to laptop on 5ghz. Would also be nice to have the 2.4ghz signal boosted as well
When I go upstairs, both laptop read 300 ghz and I can stream between them just fine.
View 3 Replies
View Related
Oct 14, 2011
After an upgrade of the WRT120N to firmware Ver.1.0.06 (Build 01) every device I have tried to use WPA authentication with will authenticate / associate with the device then drop the connection just prior to recieving a DHCP address.I have tried a Dell latitude laptop with the broadcom chipset, an iPhone 3GS as well as an motorola with google pad device and all experience the same problems.I have removed all mac address filtering, and re-enabled the essid broadcasting only to have the same problem persist despite stripping everything down to just WPA.
View 2 Replies
View Related
Aug 27, 2011
I've rolled back my E4200 router to the old firmware 1.0.0.1, then set up a media server.It generally works (e.g. it streams pre-existing media files to other devices). I can copy to this external drive small (say, < 1 MB) files. The drive has enough free space. However, I cannot copy to this external drive large (e.g. 700 MB) files.
View 5 Replies
View Related
Apr 7, 2012
I recently upgraded my internet speed service from my ISP (Brighthouse). They installed a gateway to replace their old modem, but I have had it bridged so it should act as a modem. Speedtest.net shows downloads on the order of 40-50 Mbps and uploads around 5 Mbps. If I try doing something interactively that pushes the speed and size of files (like flying over Google earth using my mouse to guide the direction and speed) my connection seems to hang. I have to reset the router (unpower and repower it) to get my internet connection to work. This has also happened when I quickly downloaded a series of large images - I click to get the next page fairly soon after the current page has finished downloaded. My router is a WRT350N.
View 6 Replies
View Related
Mar 10, 2011
Product: Linksys Wireless-G Broadband Router WRT54G
Version: 6
Firmware: Has Been Updated
I am directly connected to my router. Lately, I have been receiving high latency spikes and total loss of internet. The problem must be related to my router, because when I connect to the internet through my modem I don't have this problem.
View 9 Replies
View Related
Nov 20, 2011
When I try downloading from fileserve it starts downloading and after maybe 3-4 mb it stops for no reason also in JDownloader it starts and after 3-4 mb it says no permission to write to hard disk all other filehosts are working fine and all other downloads work perfect.I'm using ESET smatr security but I'm disabling Web access Protection and the firewall is set to learning mode so all attempts of any application to connect to the internet would be allowed
View 1 Replies
View Related
May 15, 2013
I have a Dell Studio PC with a Dell Wireless 1397 WLAN Mini-Card. OS is Windows 7 with SP1. Intel Core 2 Duo T5800 2.00 GHz
In general I have no problems with my WIFI with simple browsing and most of my routine activities online. But any time I stream video (like youtube), music or download a large file, my WIFI spontaneously turns off. I need to either restart the computer or put the computer to sleep/wake it up for the WIFI to work again.
I have the latest drivers for the Wireless card. I scanned the forums and didn't see this problem reported elsewhere. I realize this is an old computer so I may have to install an external wireless adaptor, but I wanted to ask around before doing so.
View 8 Replies
View Related
Jan 2, 2011
I need to limit the amount of data my child can download each day and can't find a simple program to do this. I have a Verizon MiFi access point in my house with a 10GB monthly cap. I need a program that I can install on a single computer that will allow say, 100MB per day data transfer, then not allow any more internet access on that computer till the next day. I'm OK with computers, but not a guru so simplicity of setup & use is important.Most programs I've seen are geared for complex network monitoring by IT pros, and the ones geared for monitoring kids mainly restrict access by time spent online, whereas I need to cap usage by the amount used each day. Computer is an Acer laptop and an eMachines desktop, both using wireless access and both running Windows 7.
View 7 Replies
View Related
Sep 5, 2011
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies
View Related
Oct 4, 2012
I previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
View 4 Replies
View Related
Jan 16, 2013
I am experiencing strange problem about slowing down the internet speed after downloading is stopped in between. I then have reboot the desktop to regain the speed.
My networking as below:
DSL Modem
Dlink DIR-655 Router
Desktop A (Wired Network)
Desktop B (Wired Network)
Laptop (Wireless Network)
If I am downloading a file (1gb) on Desktop A and for some reason I have to stop it, then internet connection is desktop A , desktop B and laptop is almost killed. To get the speed back, I need to reboot Desktop A. All computers are on Windows 7.
If completely download the file, the internet speed is good on all the computers. Before downloading the speed is: After stopping the download the speed is :
View 2 Replies
View Related
Feb 28, 2013
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Dec 18, 2012
I want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies
View Related
Nov 23, 2011
How To Reset E2500 Router
View 1 Replies
View Related
Jan 23, 2012
I am trying to setup a WAP with my linksys 2500. I am currently using a Gateway connected to my DSL and am looking to set up the access point through the E2500.
View 1 Replies
View Related
Nov 18, 2011
So, i have a e2500 router and find that every so often, I have to unplug it and reset it because I am losing my internet connection.
View 7 Replies
View Related
Dec 22, 2012
How to set router to use as Slind Box Pro?
View 3 Replies
View Related
Jan 4, 2012
I currently have my E2500 connected via wired LAN (not WAN) port on another router. The E2500 has an LAN IP of 10.0.0.2 and the router has 10.0.0.1 and a dhcp range outside of these. DHCP is disabled on the E2500. I can use my E2500 as a wired access point with no difficulty I plug something in and it calls the router and gets an address, but I can not get DHCP through the wireless of the E2500.
View 2 Replies
View Related
