Linksys Wireless Router :: E3000 Trying To Setup A Static IP
Dec 13, 2011
I upgraded from a WRT54GS. I have an XBOX that I am trying to setup a static IP for. Every time I try I get an error message stating invalid static route. All I am trying to do is set it up the same way my old router was so when I specify my XBOX as DMZ Host I don't have to worry about my XBOX ip address changing like it currently does.
I have an E3000 that I am just setting up.I have two issues:
1> I am replacing a WRT110. I had the old router set with a static IP address supplied by my ISP. I configured the E3000 with the same address and I cannot access the internet. Are there any tricks to setting this up on an E3000?
2> As configured I there is a guest network setup. BUT when I access the router I don't see the tab to be able to configure it.
I've small corporate network with Cisco 800 as main DSL router/firewall/DHCP. I'd like to setup Linksys E3000 (firmware: 1.0.01) as bridge (no DHCP, only wireless repeater), but there is no "bridge mode" in E3000 interface
I have comcast Triple HD cable internet and I have been using a low end 5 year old Linksys Router. I decided to upgrade and get the E3000. So far I have had no luck at all getting it to work. Setup fails to even connect at all. I spent 2 hours on the phone with tech support. There were in trying to get it up and running but we have been unable to get a TCP/IP number from my provider (comcast). I hooked up the old router to see if any of my settings looked unusual but they seemed normal.
My router wasn't giving out proper ip addresses so I went through the steps to reset the router to factory defaults. After I tried to run the setup off of the cd which came with the router and the program is saying it can't find my router
I just installed my new Cisco E3000 and configured it over the HTTP interface, as I have on previous routers. I am unable to find any setting for the "Guest" wireless network (outbound internet only), or the Parental controls. Both of these are features of interest, and they're simply not listed in any of the web-based settings.
Puzzled, I did a Factory Reset and configured it via the Cisco Connect instead.. this had the Guest feature and Parental controls, but none of the other features I need, like QOS, or Port Forwarding, or DHCP disable.
It seems like the Web interface only configures some settings, and the Cisco Connect configures other settings, but I can't use them both.
Where does one set up the additional password for Guest access? Other than this, the router works fine on 2.4 & 5 GHz, nice..
I'm trying to set up an Iomega Home Media Network Cloud NAS and I'm having problems with opening ports 50500-50599. I have opened port 80 and 443 successfully and included the above port range above as well, but when I check it on www.yougetsignal.com the ports 50500-50599 are still closed. I even tried to split the range in two parts, and still no success. I have been in contact with my ISP and confirmed they do not block any ports in the 50500-50599 range and that the cable modem (a Motorola SBV5120) is operating in Bridge Mode.
I am finally duffing my WRT 610N (N=Never consistent in performance) main router and WRT54G that I am using up in my shop as an expander. Now I am going to a E4200 Main Router and E3000 for my secondary router (Truthfully a dual band expander).
Am I going to just simply Flash my 610 to default , disconnect it and pack it away , Setup my new E4200 , Plug in my E3000 into port 1 and go about giving it a separate IP Addy? Or can I expect a **bleep**? Any setup tips?
Wirelessly I am running 2 laptops , a PS3 , Xbox 360 , Epson printer , a picture frame and Samsung Blue Ray and TV, and on occasion 2 android phones. On the Wired side (Ethernet) I have a Sling Box , a Desktop , and the router up in the shop. This is the normal load and never everything all at once (Although it has been done).
Just checked that my ISP provides me with two Static IP's, called them and they confirmed its running, however the modem that they gave me only has one ethernet port, to which my Linksys E3000 is connected. I am trying to set up this new IP and dedicate it to my new WHS 2011 machine, so I can remote manage it. It having a static IP of its own isn't much of a problem, but I would like to know how to do so.
I have a Linksys E3000, have had it successfully connected for three months now. Recently I attempted to connect my xbox 360 to the wifi and had issues connecting it. So I called ATT to obtain the PPPoE username and password, which they reluctantly gave me. Entered that into the xbox and still unable to connect, so I have given up on the xbox for the time being, I'll post that issue in a different forum. Where my issue is now is since contacting ATT the WPA2 password I set up for the router no longer works. I cannot access the router setup page, and I cannot add any new wifi devices. Although, all of the previously connected wifi devices are still connected to the router despite this issue. Is there anyway to make the old password work, or do I have to reset the router and start from scratch, and God forbid contact ATT again?
I have Astaro UTM running on an old computer as my only firewall right now. The Astaro also serves as my DHCP server. My Wifi is provided by a Linksys E3000 running DD-WRT software. NAT/SPI are disabled on the E3000, and it forwards DHCP requests to the Astaro. All my network clients connect via wifi/ethernet to the E3000.
All clients --> E3000 (no firewall) --> Astaro --> www
I am considering setting up my own personal cloud server using a Synology NAS that I can access remotely. I would also like to remotely access my Surveillance DVR. I would like to access them via VPN or portforwarding. I do not want to use DMZ.
I would like to utilize the SPI firewall on the E3000 to provide an extra layer of defense. I would like the NAS and the DVR to be on an external LAN between the Astaro and the E3000...and all other clients being on an internal LAN behind the E3000. I have the necessary switches/cables to make this work.
My question is...How do I configure the E3000? Can I have both the internal and external LANs on the same subnet? Do I have to use the NAT on the E3000? I'd rather not...since that will render the Astaro's reporting functions rather worthless.
I would like the Astaro to remain the only DHCP server. I would like all internal LAN clients to be able to reach out to the external LAN/WAN...but the external LAN should not be able to reach into the Internal.
I have a 1Mbps adsl connection shared by 4, mine is wired & rest of them were via wireless. Its difficult for me to browse a single page in facebook & don't even think of the youtube videos etc.Is it possible to setup the qos static ip on the router or a certain speed (kbps) to my pc with any third party softwrae & the remaining speed would be shared by the others.
I have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
Primary Access point 192.168.0.1 DCHP server with reserved IP addresses for server and PC's and smartphones Port Forwarding Set for Server at 0.004 : 80 Port Forwarding Set for E3000 at 0.002 :21
Secondary (E3000) router 192.168.0.2 DCHP server is disabled Port Forwarding is Not being used connected to primary router LAN port 1 by LAN port 1 on E3000
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?
I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.
I have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
I had a failed Tomato upgrade and now Connect Setup can't see router to revert back to original. I get message 82BD0101 or computer not connected to router. Also the http://192.168.1.1 trick won't work. Is there any way to restore besides 30/30/30?
I would like to override the DNS servers provided by DHCP via my ISP. The other settings I would like to preserve (like my assigned IP).How to achieve this with E3000 ?
It seems like after a certain amount of time, maybe a few days... my E3000 gets slowww.. I'm talking dog slow. And it's not just the internet, I have a media server connected to it, and usually when I put something on it, the transfer rate is about 3.5MB/s (not bits, bytes). But everything is slow, I top out at speed of maybe 1/6 normal on the internet as well.
We have a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..
Has anyone tested QoS on the new E3000? Whenever I add an application (e.g. Voice Device) and set priority to Medium or High, my upstream bandwidth for everything else is immediately cut significantly, even when I'm not using the priority application.
For example, with QoS disabled, I can consistently get 10Mb upstream (speedtest.comcast.net). As soon as I enable QoS, upstream is capped to exactly 2Mb! On my old router, there was an option to set the total upstream bandwidth -- but on the E3000 there is no such option that I can find.
just bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
I just bought an E3000 about 30 hours ago and just unrealistically my router now doesn't want to give me any WiFi at all. I tried reset button, tried re plugin all of my system as well as pressing for short and long period the middle button that indicates WiFi is accessible. I already bought 3 linksys routers.
Looking at upgrading my router to an e3000 however I've got a couple of questions. I might come across as a bit thick with this one but I have read that you need a modem to make the router work, I can't get my head around this as I've not come across this before. I always thought the router was the modem!! I've also heard that the E3000 only works with cable ISP and not ADSL, is that true?
My adolescent son wants to create a server to host video games. We, the parents, want to separate our computers and files from all the crazy security risks my son and his friends take, while allowing them to learn by their mistakes.I want 2 separate networks, or does this make sense? Would love to have our computers (assorted PC's, Macs, both laptops and desktops, running Vista Ultimate, Windows 7, OSX 10.5 and up), ipods, TV's, Blu-rays, wireless printers, etc. isolated from our son's computers, ipods, TV's, XBox, Blurays, wireless printers, (as well as the digital stuff his friends bring over).Since security is the reason for this, would love any tips over and above Brian Posey's article on Tech Republic (5 common security mistakes people make on setting up wireless networks, or something like that)We have Optimum high speed (testing up to 65 mps) internet service and 5 static IP addresses to work with.
I have FiOS and their supplied wireless router Actiontec #MI424WR. I have home theater equipment that uses the newer N signal so I purchased a Linksys E3000 Wireless-N Router. I have one of the LAN outputs on the Actiontec feeding the Linksys input and Wi-Fi turned off on the Actiontec. This is working good for my wireless home theater equipment but I am having problems with my wired speed. It has gone from averaging anywhere from 20 to 30 mbps on numerous test sites when plugged into the Actiontec to averaging around 10 mbps when plugged into the Linksys.
1) Is my wireless N speed going to top out at 10mbps or less since that is all the router is showing on wired? Shouldn�t N be broadcasting a faster speed if given the ability?
2) I have my computer currently plugged directly into the Linksys verses the Actiontec. This makes it easier to program the Linksys router. Since I am no longer using the wireless part of the Actiontec there really is no need to be plugged into it. Is there anything I can do get the speed higher on the Linksys, a setting I can change? Will I have to plug the computer back into the Actiontec to get the higher speed and then move it every time I may need to make a change to the Linksys?
Want to switch to dualband E3000 from older, working fine except needs resetting often. What steps do I need to take? I do not have E3000 setup disk. I fear that I will go down a path that makes both of the routers unusable, at least down many hours.
I've been searching how to make my E3000 use the DHCP and IP address on my primary router so I can share printers and computers on same gateway IP. I tried turning off DHCP on E3000, but not sure how to tell it to use the DHCP from the source "INTERNET"
shows connection to cable modem, shows IP lease, able to renew and release lease. shows all DCHP clients, but does not allow internet to get through. tried cloning old routers MAC, no dice.
