i bought a new linksys WRT120N router and configured it. I have internet and connection is good.But i experience a very anoying problem. Router restarts from time to time. And it work some time and it restarts again.I updated the firmware expecting that this will solve this problem, but it seems that it didn't solve it. Routrer continue to restarts unexpectedly.
View 3 RepliesI just bought a WRT120N and at different times it will randomly restart and disconnect all the computer on my network I have 4 wired devices and 4 Wireless devices.
View 9 Replies View RelatedA day ago, I was having trouble with my apartment modem, and due to a busy schedule, was only able to do a quick "Unplug and reset" which seemed to work at first, but eventually it stopped working all together. Today, I traveled from my apartment to my "home" home, where the wireless network is set at a "Home" security level. However, my wireless now will not connect at all. It continues to cycle through "Identifying" yet cannot make the connection. It works through a LAN connection however.So far, I've attempted the follow:
- run>ipconfig/all, ipconfig/reset, etc
- winsock reset
- system restore
My computer is a Samsung RC512, running windows 7. Here's the paste from my ipconfig/all:
Windows IP Configuration
Host Name . . . . . . . . . . . . : PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
DNS Suffix Search List. . . . . . : hsd1.pa.comcast.net.
Wireless LAN adapter Wireless Network Connection 2:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
Physical Address. . . . . . . . . : DC-A9-71-93-16-52[code]....
Is there any way yo restart the WRT160NL from the web interface? I've had several routers before this Linksys and all of them had this option. In the web GUI of the WRT I can't find the way to do it and I have no other solution of unplugging it and plugging again.
View 6 Replies View RelatedWhy I must restart my e4200 after 2-3 days when I want to connect my device like notebook or phone to the router. After restart my device can obtain the ip. I hardly to turn off the router.Is something wrong with my router ? [code]
View 2 Replies View RelatedI'm constantly losing wifi connection and having to restart my Linksys E2500 router
View 4 Replies View RelatedLinksys WRT120N to 811.11n? I set to 811.11N Only with 40Mhz, saved and reboot the device but the signal continuous in 811.11g.
View 3 Replies View RelatedOne of our Routers 7204 rebooted unexpectedly. I try to access Output interpreter but is not working. The output from our router is the following:
WAN-ROUTER#sh version
Cisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.4(15)T2, RELEASE SOFTWARE (fc7)
[Code].....
I bought a new Linksys WRT120N modem which is working great, but the wireless for some reason isn't working properly. My computer is able to sense the exsistence of the connection tho. I've tried using other computers to connect to it, and still the same problem, can sense but cannot connect.
View 8 Replies View RelatedI currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
View 9 Replies View RelatedI have a WRT120N and have been trying to set up priorities using the QoS under the tab Applications and Gaming. Everytime I "Save Settings" it does not save. It refreshes the page and deletes everything I just set up.
I did Live Chat and they told me it was my router. I returned it and got another one... Same problem
I'm using an Static IP adress and i'm using wrt120n router, but to connect the internet i have plugged the internet cable in the 1,2,3,4 (doesn't matter which one) slot. So now i'm just using the wirelss part of the router without "routering" if i can say so. When i put the internet cable in the Internet slot of the router, the laptop just cant connect to internet - it shows Unidentified network without Internet Access. I don't know what type of changes i have to make in the WEB interface of the router. I think i have to set the type of the connection - now is DHCP and may be to put my IP adress, DNS, Subnet mask in the router settings, but don't know how exactly. I've tried to set up the router with the CD-interface but same thing happened - Unidentified network when the cable is plugged in the Internet (yellow) port. How to set up the router to be a router, not just a wireless switch?
View 9 Replies View RelatedMy roommate and I recently got a WRT120N to replace an older Linksys router that was exhibiting the same problems with less frequency. Indeed, the entire reason we got the new router was to fix these problems. Alas, they have become worse.Anyways, what's happening is that the router constantly resets itself. It does this every 20 minutes to an hour and doesn't seem to be related to how much traffic it's dealing with.It's not just the internet going down, it's the entire network, and not even just the wireless part. My computer has a wired connection to the router and, and I get told "A network cable has been unplugged" every time it happens. Then, if I look down at the router, I see no flashing lights, just the steady glow of the power light. It always fixes itself after 10-15 seconds, but it's very annoying. Certainly, playing games online or having a conversation on Skype is made more difficult.As previously mentioned, we replaced our older router because it was exhibiting the same behavior, but the new one does it with greater frequency. At the very least, the router does reset itself instead of needing us to cycle the power. The setup was slightly different with the old router: I was using a wireless connection with a WMP54Gv4 which I've had to disable since it bluescreens the moment it so much as sniffs a signal from the WRT120N?
View 9 Replies View RelatedIs there anyway to disable WPS on the WRT120N router?
All I can do is switch the "view" from WPS to manual configuration in the management console...this doesn't actually disable anything.Maybe I don't understand WPS security, but what's the point of using a 20 character WPA2 password if WPS has an 8 digit PIN that I can't change or disable?
I just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
View 4 Replies View RelatedI have a WRT120N router installed in my office.All PC and Laptops are connected to it via WiFi.there are about 3 PC and 4 Laptops.The WiFi keeps going Off now and then..and comes back on in a minitue or so.
View 9 Replies View Relatedwhy are some of the lines solid & others dotted on the map page?
View 4 Replies View RelatedI removed my ps3 from my network map and now i can't connect it back. How to do it?
View 1 Replies View RelatedI plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
View 3 Replies View RelatedI have several computers and printers connected to a WRT120N router which is connected to 10mpbs DSL. The computers are all running WIN7 and are hardwired to the router. On the one PC, it keeps losing network connection. I've tried upgrading the router's firmware, reset, etc. to no avail.
I think it may be related to the same IP address being assigned to multiple machines connected to the router. Is there a way to set specific IP addresses to each item connected to the router to see?
I don't have any problem with the wireless computers connected to the router but the wired one keep geeting disconnected. I'm loosing the internet many times a day on thiis one. Like I said the wireless is ok. My old router on my computer ( wired) was working well before I installed the wrt120n.
View 3 Replies View RelatedI've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies View RelatedI can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
View 1 Replies View RelatedI replaced a WRT120N router with a new one thinking that the old one was damaged. During setup, the router wasn't recognized. I used the same connection for a line from the internet to my LAN connectin and the line works fine. Connecting through the router is no good.
View 1 Replies View RelatedI am considering to purchase a Linksys Wireless router, but I just don't know which one to select.There are so many different types that seem to have very similar (if not equal) specs.If I just limit myself to the WRT120N, the WRT160N and the E1000, they all have 4 ethernet ports (10/100), and they all support 802.11 b/g/n for the wireless part.Obviously they all promise a blazing performance, and wireless coverage throughout the whole house, without (many) blind spots.But if their specs are the same, why are they different types?
View 2 Replies View RelatedSeveral days ago there was a huge storm, and I think a thunder burned the WAN port of my linksys wrt120n router. Everything else is working good, I can detect the local network but I don't have internet. My internet connection is also working good. My question is, do I have a possibility to use some of LAN port like a WAN? I'm only using 2 of 4 LAN ports. It would be very useful because it's a pity to buy another router just for a not working WAN port.
View 3 Replies View RelatedI am trying to manually setup a WRT120N router. I am using my laptop (hard wired) for the initial setup. Okay, everything is working fine until I unplug the ethernet cable and try to go wireless. Will not connect to my network. I am also having this problem with all my other devices.
I had everything running fine on a WRT54G, I just wanted to try out the WRT102N. I did change the SSID name form what I was using on the WRT54G.
I'm having an issue where essentially my only course of action is to unplug the router and plug it back in. I can connect my laptop (Dell Inspiron N4010) and my phone (HTC Inspire) once. But then if I put my computer to sleep, or I take my phone out of the wireless range and come back, I cannot connect again. I've gone through and played with the settings (changing the upnp, the beacon intervals, the channel, etc) but to no avail. Invariably, I always have to come back to unplugging and plugging back in.
Also have a Kobo E-Reader and a wireless Canon printer. The whole point of a wireless printer was so that it would stay connected and I can print from my laptop. This router is making this useless.
My mother in law bought my daughter a impression android tablet for Christmas it connects fine at public hotspots but I can not get it to connect to our wrt120n router at home. I have tried everything I know to add it. It asks for the password then says getting IP address then disconnects.
View 2 Replies View Relatedhow to get the factory firmware version 1.0.01. I have a problem with the settings. I want to return to the basic version, but can not find anywhere else.
View 4 Replies View RelatedHow to reset the linksys cisco wrt120n router.
View 4 Replies View RelatedIs Linksys WRT120N still supported by cisco? I ask this because of the WPS "CRITICAL" vulnerability and no news of a patch since a month... and
*WRT120N firmware is propietary
*Not supported by DD-WRT/OPEN-WRT/FREE-WRT
the kids received an iTouch for Christmas and I've spent the last 3 hours trying to get them connected to our home network. I have an existing network with two computers, I'm using a WRT120N router, the iTouch is picking up the network but when we put the password in we get an "unable to join network" message.
View 3 Replies View Related