My wrt400n was working great but since last few days internet keeps dropping. My modem is all good and up and running. Its just router keeps dropping internet. SO i have reset the router and than it works.
View 6 RepliesMy WRT400n has started dropping the wireless signal 4 to 5 times a day. Somet times it fixes itself but most of the time I have to re-boot the router to connect a wireless signal.I looked for a firmware upgrade but there hasn't been one since 2009.
View 4 Replies View RelatedI'm having a little trouble connecting a new computer to my wireless network. I have a WRT400N router and I'm connecting an older computer to it. The computer runs off Windows XP and the router itself is a WUS854G. We can get the adapter to say that it is connected to the network, but the router will not assign it a new IP address or even acknowledge that it is connected on the MAC client list. We manually forced a new IP, which allowed the computer to connect (though, again, the router did not show that it had been connected to.) but despite the connection being "Excellent" we could not access the internet. Furthermore when we tried to refresh the connection the IP address reverted to the original setting.
View 2 Replies View RelatedWe had a power outage the other day, and now the wireless router cannot connect to the internet. Network Magic shows there is no connection from the device to the internet. I tried repairing it through Network Magic but it wasn't able to fix it.
My PC is directly connected to the wireless device by LAN cable. If I connect the PC directly to my DSL router I can connect to the internet, but not if I connect to the wireless router and from there to my DSL router. I tried resetting the wireless router to factory defaults and then going to [URL] and resetting up the router security settings. But Network Magic still shows the bad internet connection.
I then tried resetting the router to factory defaults again and installing it from scratch using the setup CD but that failed as well. I'm not at home right now so can't remember exactly at which point it was but I think it was either when the setup wizard tried to detect the device or install the device.This is the second time I've had to reset up my router due to power outage. Last time I was able to get it working by doing the first steps above.
I have had a problem with my WRT400N wireless Linksys router. Whenever my router restarts or if the DHCP lease expires, I'm unable to connect to internet. During this time I can access the router, but not the internet. Oddly something that seems to "fix" this is if I use my nintendo wii to access my wireless internet at that time, all computers on my network are able to access the internet. However this is annoying to do since this happens once a day from DHCP lease expiring. Using any other computer to attempt to access the internet at this time would be unable to get a connection until I do the "fix" with the Wii. WRT400N
View 8 Replies View RelatedWRT400N worked great for 18 months.
Last week the Verizon-supplied DSL modem went bad (wasn't receiving data) and was replaced.
Now I can get Internet direct out of modem, and when I connect it to router the router's Internet light is on, but it seems to stop there. Devices connected to router via Ethernet or wifi don't get Internet.
I'm able to get to the router's admin console via Ethernet and wifi, but no Internet.
I am trying to troubleshoot my own router (Linksys) issues with using Lync and accessing some sharepoint sites that are internal to my company's network. I am connecting to the Internet using a Linksys router (WRT400N). When I have my work laptop using RESCUE GFE hardwired directly to the modem - and then connecting to VPN - I can connect to Lync and work normally. However, when I move connection via the router - I can no longer connect to Lync nor access some Sharepoints. I can access VPN fine but with Lync I get an error stating "Your Lync account does not allow access from outside your organization's network. Please connect to your organization's network and try again. However, I am connected via the VPN.this connection worked with a prior laptop using WinXP (I am no on Win7) and the connection thru router and using VPN worked with Communicator.I unfortunately had to reset my router - so I cannot recall if there were port settings established from the last time I had to set up the network. I didn't save the configuration; note to self - save configuration in future.
View 1 Replies View RelatedI just did a reformat on my laptop, therefore I had to reconnect with my router. I put in the correct encryption key.. however as soon as i got connected, it just kept saying *Authenticating* for about 5-10 minutes then it disconnects me.. What i can do to stop this?The router itself was installed on a shared computer (I live with several roomates) and that particular computer got replaced.. does that matter to the router? the new one doesn't have the program installed.
View 1 Replies View RelatedRecently upgraded to WRT400N from older 54G. Opened ports to my Linksys IP Cameras and can access via DynDNS address (using Modem addressort) from inside my network but not remotely. If I disable SPI Firewall it works from outside my network ... am I missing a step ... never had this problem with 54G and although I run software firewall on my computers I like the thought of added security of a firewall on my router.
View 2 Replies View RelatedBeen having random connection drops for the past few weeks where I would see the network connections to the router just drop either on a wireless connection or a wired cat 5 connection. As of tonight I cant connect to the router at all. If I disconnect and reconnect the power after 30 seconds it will come up for a short time but then I will lose it again. linksys as my router is out of warrenty. I'v searched around for similiar problems people have been having, but it seems like mostly involve just the internet connection. I still have the same firmware for the routers as the day I purchased it and the router sits on my desk in a ventilated area not overheating. I can do to further diagnose the problem, I have even tried resetting to factory defaults. I try to diagnose the problem or see if my router is just dead.
View 3 Replies View RelatedI was able to connect to the n portion of the router with the xboxs fine until last friday. now i can see the n network ssid fine but the xbox won't connect to it.
my pc connects just fine, i've powered cycle the router, tried renaming the router, opened all the required ports, reflashed the router to the current firmware.
Check to see if there is a firmware upgrade and there is. Well I updated it with the newest and only one out there. I did the upgrade, said sucessful and now it will just random reboot or something........ every few minutes the power light starts flashing....... then all the light go out, then power flashes again and it comes back up. I have tried many times to reflash it with that new firmware but no avail. I wish I had the old firmware back because it was working fine till I did this upgrade.
View 5 Replies View RelatedI cannot get internet Wake on LAN to work via my wrt400n . (It works fine on my LAN - so I know that the pc is configured properly. Further, I know that port forwarding is set up correctly, as other applications are using forwarded ports and are working correctly). The issue seems to be that the magic packets are being blocked by the router or they are received but the router doesn't know where to route them. I monitor the network and the never see the magic packet on my subnet. how do I set up a static ARP route on the wrt400n? I suspect that I may need to create a static ARP to resolve the issue.
View 1 Replies View RelatedI would like to configure it as an access point on my LAN, similar to the way my WAP55AG works.My research on the Internet and on these forums indicate that I have to disable DHCP on the router as well as use the LAN ports to connect it to my network.I am able to turn off DHCP, but assigning it a static IP address is challenging.I can set the IP address, but I am unable to set the subnet mask to 255.255.254.0 as I am only getting a set of SM in a drop down list whick are all 255.255.255.x
View 9 Replies View RelatedI have a WRT400N and approximately every 30-45 minutes the router will drop all connections (wired and wireless), all the lights will go out and then power light (far right light) will flash for a minute or so. I have tried connecting directly to my modem and I have no problems at all.
View 7 Replies View RelatedI have a WRT400N that loses connections for my PC and other devices in my house (IPHONE, IPAD etc.).Sometimes it fixes itself other times I need to to a hard reset to boot the router and then evryone can signin again
The Firmware Version: 1.0.01 B19
The operating system on my PC is WIndows 7
I have been experiencing intermittent issues with download speeds of 1-3 MB and ironically upload speeds of almost 10MB. When everything is working fine I get download speeds of about 35MB and upload speeds of 5MB which is normal. This issue comes and goes. I had Comcast come out several times and we finally pinpointed it back to the WRT400N router. The Comcast modem is a Cisco DPC3008 model. I know there are known issues with the Cisco WRT400N but have had a hard time finding the information. Any known issues for this model and if so what are the fixes. BTW, the firmware is up to date.
View 2 Replies View RelatedI have spent several hours with Linksys support (six calls) and my ISP (2 calls) and still can't get my router working. It will work for about 5 minutes or and then drop Internet access. If I unplug and reboot, etc, it will work for another 5 minutes or so and then drop signal again.
View 9 Replies View Relatede4200 internet keeps dropping
View 9 Replies View RelatedI have a WRT54G wireless router and it goes through periods where it constantly has to be reset cause it keeps dropping the internet connection. Once you do a power cycle it starts working right again. But sometimes goes out 5mins later.I have the router hooked up to a Windows XP computer via an ethernet cable...and I have 1 Windows Vista laptop, 2 Android phones and a PS3 connected via wireless.The PS3 is set up following these directions: (not sure if this is what's screwing it up)
"Step 1:Open a web browsersuch as Internet Explorer.
Step 2:Go to the Address bar and enter your router's IP address ("192.168.1.1" is the default IP of most Linksys routers) then press [Enter].
Step 3:When the router's web-based setup page appears, click Applications& Gaming then click DMZ.
Step 4:Select Enable on DMZ and under DMZ Host IP Address enter the PlayStation®3's IP address.
- Try 192.168.1.10 or 192.168.1.20 Save Settings.
- This IP address will need to typed in manually during online setup on ps3. I think its the first address you enter (I think this is the game's IP address).
- Use 192.168.1.1 for the wireless router's IP address on your PS3.
Step 5:Now, click Administration and Disable UPnP. Make sure you also disable UPnP on your ps3 online setup. Save Settings.
Step 6:Click Status. Write down the DNS 1: dns number and DNS 2: dns number on a piece of paper. You will enter these for DNS 1 and DNS 2 numbers during online ps3 setup. NOTE: The IP address listed on the Status page for your wireless router is not used for any setup on your ps3. Remember, to get into ps3 online setup, you have to choose Manual during setup so you can enter these numbers.
Step 7:The WP key crap and whatever during online setup should be skipped unless you specifically setup some kind of password for your wireless router when you installed it. I didn't and just left that part blank and skipped over it.That should get your wireless router and game setup. If you're still stuck, drop me a message.And, remember to do this setup after that:Linksys has a great tech support at their site. url...
I have a ps3 and did all of the wireless and ps3 online setup for it using their site technical support. Doing that seemed to throw a monkey wrench into my internet connection a while after that. I just left all of my game settings in place and did this: Logon on to your wireless router. To do this, you will probably go to url.. by typing this address into your address box on your internet explorer. Logon. If you don't know how to logon, go to and follow the instructions in technical support.
Just bought a WRT400N and set it up using 5ghz and 2.4ghz bands, and using WPA TKIP for both. Problem is that both my laptop and my iphone occassionally lose connectivity and my iPhone says that my WPA key isn't valid.
View 4 Replies View RelatedHaving a problem with port forwarding on their WRT400N? I'm forwarding one service (https) and this stops working if it's not accessed after a 10 days or so. The only way to get it to work again is to reboot the router. I’m running the “latest" firmware, which is an oxymoron considering it's been over 12 MONTHS since Linksys updated the code... Which is appalling considering this appears to be their flagship wireless N router.
View 5 Replies View RelatedI have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies View RelatedI've had been successfully using a WRT400N to extend my wireless network as follows:
The WRT400N connected to my network via an Ethernet port in my kitchen. The cable ran down to a corner of my basement connecting to Verizon router that brings in our Internet, TV etc.
The Verizon router's poor location was a problem, and placing the WRT400N in the kitchen worked perfectly, providing excellent network access and Internet to wireless devices throughout my home. It worked fine for over a year.
Recently, we had a power outage which reset the WRT400N to factory settings. and I am having trouble getting it to work again. I set it up in the first place, but am now having difficulties. Clearly, I am no guru!
I tried to get it going again by: 1) plugging the WRT400N into a PC and giving it a new IP address that would not conflict with the Verizon router (both default to 192.168.1.1) 2) turning off DHCP, 3) renaming the router, 4) changing the router password, 5) setting up a WPA2 security key.
I then plugged the WRT400N back into the kitchen Ethernet port, but something is wrong. Wireless devices cannot find the WRT400N.
The good news is that I can "see" the WRT400N through any PC on the network via a browser and access setup, but the bad news is that devices cannot see or connect to the wireless signal.
When I go to "Status" it shows the IP address, subnet address and default gateway all at 0.0.0.0. On the SETUP page, it has the correct router address (192.168.1.9), and a subnet mask of 255.255.255.0. Not sure if it is supposed to be this way...
I've had the WRT400N for about a year and a half now and just last night it stopped sending out data when connected to my cable modem. I've tried connecting the modem directly to my Mac and it works just fine (that's how I'm sending this message now). But when the modem is connected to the router, I get no data. It connects to both the 5 Ghz and 2.4 Ghz networks, but it refuses to send data through the pipe. I've tried power cycling both the modem and the router to no avail.
View 1 Replies View RelatedI am trying to set up an access policy on my WRT400N. Whenever an access policy is enabled, all internet acess is completely blocked. This occurs irregardless of what the access policy is supposed to block. Even a blank access policy that allows access to everything and doesn't have any computers registered still blocks everything. How do I get it to stop completely blocking internet access?
View 9 Replies View RelatedThis happens intermittantly. This results in most connections (but not all) being dropped. I will be unable to connect to web servers. My connection to videogame servers will drop. However, AIM will stay connected. These were done simultaneously. The same thing happens with my Cisco AE1200 and a D-Link 802.11g adapter I have. Disconnecting my adapter and reconnecting it solves the problem. I have tried doing a factory reset on the router and installing the latest firmware. It seems to happen more frequently when I am doing a lot of throughput (downloading a game on Steam, for instance) but other times it will happen when all I am doing is playing a game (like Tribes Ascend) which uses very little data. This is extremely frustrating. When I pay more than $150 for a piece of networking equipment, I expect it to last more than 3 years.
View 4 Replies View RelatedCurrently running Windows 7, with internet explorer. I have most recent firmware installed on my e2500. The unit drops wireless connectivity on an intermittent basis. Sometimes after 5 minutes and sometimes after 20 or 30 minutes.
View 9 Replies View RelatedI had the 2 Wire Box that received TV and internet. Called my ISP and they gave me this access point to use instead. I hooked it up and it was fine for about 2 weeks. Suddenly for no reason it started dropping. Noticed it first when online gaming on my PS3. Checked laptop and all wireless devices down. Takes about 30 seconds.
View 1 Replies View RelatedWired connection to the router works fine. But it drops all the wireless devices (PC, phone, tablet) multiple times each day, sometimes only 30-60 minutes after reconnecting. Power cycling the router "fixes" the router and allows reconnection. There are 2 topics in the FAQ section that looked good: Getting poor or no signal from a wireless routerTop causes of dropping wireless connection on a Linksys routerbut clicking on those does not bring up anything.
View 9 Replies View RelatedSet up: Router: WRT110 1 computer connected via ethernet cable 1 computer using a wireless nic card from cisco
The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).
The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
I don't understand how to even frame this problem in a concise manner, much less seek information as to how to resolve it. It's seemingly giving all priority to the computer connected via ethernet but I that's just intution speaking.
I recently changed the security mode on my router from WEP to WPA2 Personal. However, since that change, I've noticed that the wireless devices, 2-laptops, are intermittently loosing their connections. . I don't know if it has anything to do with the security mode change, but I don't want to go back to WEP for obvious reasons.
View 9 Replies View RelatedI have a WRT54G conected to a desktop through a wire, and conected to a laptop wirelessly. It starts working fine, and after a while i get no internet connection in my laptop nor my desktop. After this happens i disconect the power source from the router, i conect it back again and it starts working.
View 9 Replies View Related