I have just got viasat internet from England to replace the local internet here in Spain. I believe that My router was programmed to the old internet and wont recognize my new modem. I have tried live chat and got guided thru a few things and established an IP conflict, but lost contact before we found a solution.
View 1 RepliesMy wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies View RelatedI borrowed a linksys wireless broadband router from my uncle and tried to connect it to my pc.But it is not connecting..i mean i connected an ethernet cable to my router to pc and waited for the light on the modem to become stable..and tried to go to ip address 192.168.1.1..the page not opening....it shows THE WEBPAGE NOT AVAILABLE ...but it worked perfectly for my unclE...eventhough i disconnected power cable and tried resetting but it is of no use ROUTER MODEL NO.WRT54GC ver 2.0?
View 1 Replies View RelatedI have a WRT54GC v2.0, that was working perfectly till yesterday.I cannot access the router no more, either thru cable nor wireless, all lights are flashing.I thought it would be the power source but i have measured it with my fluke multimeter and there is 3.5v, it is probably working well.
View 9 Replies View RelatedHow to connect two PCs and one DSL router to get on the internet?I am getting IP conflict error on the PC. I can only connect one PC at a time to get to internet.
View 1 Replies View RelatedI put a password on my WRT54GC ver 2.0. After that i couldn't access internet. It keeps authenticating and never connects.
View 2 Replies View RelatedIs it possible to connect WRT54GC with telnet?
View 3 Replies View Relatedi have a wrt54gc router. I can connect to the interent without no problems what so ever, however, i try and play a game on line and it tells me it cannot connect to the EA server. My psp is running v3.03. and the router 1.001
View 3 Replies View RelatedWe are trying to connect to Internet with the PSP.We are using the Linksys WRT54GC wireless router.Went to192.168.1.1to access the settings, everything has been set to disable security featuresPSP Version 2.6Followed instrutions from a web site including setting the DNS to 67.171.70.72 on the PSPThere is no WEP, WPA or any other security codes.I just disabled Firewall in the Security ModeSPI Firewall Protection: Block Anonymous Internet Requests:It is our own home network of two computers and any one else who has a wireless card can access.had a signal strength of 100% on the PSP.But, still got message..... A connection error has occurred A connection to the access point could not be established, check the security settings for the network and try again.how to connect to the Internet using the Linksys WRT54GC?
View 9 Replies View RelatedI've been using WRT54GC for over 3 months, but about two weeks ago I started to experience some strange behavior. About every day connection slows down to a few kbytes/sec (less than dial-up). Ping to comcast.net (my ISP) shows about 50% pings timeouted, 40% pings 50ms and 10% pings about 1 sec. Rebooting router works, but only for a few hours.I replaced the modem with a different model - it didn't work, so it's not the modem. I removed router and connected directly - no slowdown occurs any more, so it's not the computer. I am running latest firmware.
View 7 Replies View RelatedWhen I connect router correctly via modem I get message not connected no matter what I do I am convinced I am doing nothing wrong having used linksys router a number of times before about 2 years ago using XP cannot. I am now connected to router now to get on internet to this site
View 1 Replies View RelatedI Have a Linksys WRT54GC router which I use as a switch. Recently I have been able to connect to the wireless connection, but I can't access the router or the internet. Computers that are using it as a switch have no problems, but they are setup with different network details.
I know that wireless is on, I have also tried pressing the reset button and wireless still doesn't work.
last night my internet stopped working. I have a Linksys USB Wireless Adapater.Model WUSB600N Ver. 2 I have unplugged and replugged it in numerous times. I have disabled TC IPV6. I have attempted to enter Ipconfig /renew and it said the following
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersXDazX>ipconfig /renew
Windows IP Configuration
[code]....
As titled have older linksys USB wifi adapter but Network magic wont add because 'other software' controlling adapter. Picked up a Dlink adapter dwa-131 usb wifi adapter but same issue, software conflict?Ive added several computers and laptops, different operating systems. Ipad, Ipod, blueRay, printer with no issues. But this USB wifi adapter has me completly stumped. This cant be this hard...dense I can be but... Is there a way simply that Im not seeing, adding a computer using a USB wifi adapter to my network thats compatible with NM?? Computer is an older Dell 8200 with XP sp3. I contacted support but maybe because my question was related to NM response was basically "your question was 'too technical call xxxxxxxx" -
View 2 Replies View RelatedIs there any firmware update for this product? I'm not hable to find it... Product: WRT54GC Version 2.0 (wwith external anthena)
View 9 Replies View RelatedI've been using my Linksys WRT54GC for couple years now, and only recently have I started to have significant issues with the device. I'm using a 2012 Macbook Pro, and my internet connection seems to be randomly dropping every now and then. Sometimes it works just fine for couple of hours only dropping once or so, sometimes it starts dropping literally every few seconds. What I usually do is quickly restart my wifi and the connection comes back right away. I also tried not doing that, and the internet connection tends to come back up after a minute or so.
I have read countless topics, also tried many things: changing MTU, the thresholds in router settings, security modes (it seemed to have worked fine after I changed it to WPA, not anymore though. I'm using no password now and it doesn't fix the problem either), changing the channel (my strongest signals around are on channel 1 and 11, thus I left mine on 6), I even reset the router today (held the reset button for 10 seconds~) but it didn't work either. I didn't upgrade the software since I heard stories about the software available on this site being corrupted or something, bricking the router, which is the last thing I'd want (I'm running on 1.00.7 now).
I have the impression (but it's just an impression, it might as well not be the case, and just me trying to find out when it happens, since it's not always that it breaks the connection while doing that) that it breaks the connection on high load, I mean when I'm for example using skype and facebook, and then try to go on reddit at the same time - the reddit webpage won't load, and the connection is lost after few seconds. But it also started dropping every few seconds while I was playing an online game and skyping at the same time today, which isn't a particularly huge problem for a 23Mbps download and 1.5 upload speed internet I suppose, and which it never did before. I have never had such issues with my PC using a Linksys USB adapter. The connection would drop from time to time when, for example, accidentally going on pages with lots of thumbnail pictures, or trying to load 15 tabs of jpgs at the same time, it was never that much of a problem really though, I just thought it's normal.
I'm trying to change my wireless router from WRT54G which been using for more than 5 years to a WRT54GC which I got from my friend. I clone every entry from WRT54G to the new one, even MAC address. Below is what I captured from the old router WRT54G when it connected through PPPoE
Login Type : PPPoE Login Status : Connected IP Address : 114.91.200.128 Subnet Mask : 255.255.255.255 Default Gateway : 124.74.12.242 DNS 1 : 180.168.255.118 DNS 2 : 116.228.111.18 DNS 3 : MTU : 1492 from the web admin interface, I can ping and traceroute yahoo.com, so can I browse any website from my PC.
and here is what I captured from the new router WRT54GC when it connected through PPPoE
Connection Type: PPPoEIP Address: 180.158.83.182Subnet Mask: 255.255.0.0Default Gateway: DNS1: 180.168.255.118DNS2: 116.228.111.18 from the web admin interface, I can ping and traceroute yahoo.com, but I cannot browse any website from my PC.
im triyng to forward a port but when i click save settings it give me a message: "Entry 10: Invalid IP Address".
View 9 Replies View RelatedI have used the WRT54GC (v2.0) router for a few years now, everything worked as smooth as butter, but a few days ago it just stopped detecting the internet connection. Everything works fine with the modem. After resetting the router, I tried to reinstall everything using the setup wizard but at the eleventh step, a pop-up message appears saying that it is "unable to detect the Internet connection" and, like I said previously, the modem works just fine. The username and password for the connection are correct (connection type: PPPoE).
View 4 Replies View RelatedWhen I run the setup CD the router cannot locate the internet connection. I'm using a Motorola Surfboard modem. My local PC works fine on the internet. My remote wireless PC shows limited or no connectivity. I have switched out the Ethernet cables with no luck
View 5 Replies View RelatedI updated the Firmware...then the WRT54GC can't work now,it's power led green and red always,I can't ping 192.168.1.1 via wired or wireless.wireless led shutdown.my laptop can't find any wireless network.
View 9 Replies View Relatedhow to change the time zone, the current time always show Firmware Version:1.01.6Current Time:Sat, 1-Jan-2000 00:08:40 and can't connect PPPOE
View 1 Replies View Relatedim using linksys broadband router model no WRT54GC firmware version 1.06....im using it since 2005 still now i didn't face any problem, but since 3days im facing a problem all of a sudden. i.e im unable to connect through Ethernet port ( through lan wire) to my PC, but i can access router through wifi.when i connect through wifi it is saying that there is no internet access. but i can access my router administration.i cross checked with another pc and another connecting cable , but same problem, no use i also tried resetting my router, updated my firmware. no use.
View 1 Replies View RelatedI get a "IP address conflict" message on my wireless network. Using a WRVS4400n wireless router with the latest firmware that is set to PPoE. Motorola 336 dsl modem is set to bridge mode. My network has 2 computers attached: hardwire desktop and wireless connection to laptop. When I contacted ATT support, they said the problem is in the wireless modem. Are there some settings in the WRVS4400n that must be set to insure that each computer gets a different IP address?
View 2 Replies View RelatedI am currently using a Thomson SpeedTouch ST780WLT router, which is working perfectly.I've got a second router currently not in use, a Linksys WRT54GC, that I want to set up as a simple switch to extend my network by a few ports.I connect the Linksys to my main router using LAN-LAN. Then I set up the linksys to have the IP 10.0.0.139 (my main router's IP is 10.0.0.138) and DNS to 10.0.0.138 etc.I've turned off both DHCP and WLAN on the linksys, to use it as a simple lan switch.
View 2 Replies View RelatedI recently changed my home configuration. I have AT&T DSL and I replaced my 2WIRE gateway with an AT&T provided Motorola Modem and a Linksys E2500 router on Sunday. For the last few days, all has been good. Last night and this morning, one of the computers in the house began getting IP conflict messages. The computer is provided by my company and uses the Cisco VPN client. I am not sure if it is conflicting because of the VPN (only seems to happen when it's connected) or with one of the other devices on the network (i have four other computers, a game system, and a few phones on the network).
Is there a way to prevent a conflict from happening again? My work requires me to have a constant connection for days at a time and these IP conflicts are causing constant headaches. Would creating a static IP address on the work computer outside of the DHCP range clear this up?
I recently purchased and installed seven WAP300N access points in a school, but they are now having intermittent problems with network access, as of right now their network is completely unusable. Specifically there appears to be a conflict between these access points and the gateway/router which provides their network clients with addresses via DHCP; BUT in the three years I have been assisting them the DHCP server on their Cisco router has never before given any problems!
All WAP300N units are wired to the network acting as standard access points and setup to pickup their address automatically via DHCP. When the problem first arose I changed to offending unit to use a static IP address to avoid what I presumed was an address conflict; however the same problem now appears to be happening with the other units as well!
My understanding is that these WAP300N units do not have any in-built DHCP server capability, is this correct ?If not, how I can disable this feature.Otherwise, it would seem to me that the units must be incorrectly using the default gateway address which they are getting from the DHCP server as thier own IP address. Unfortunately assigning static IPs to each access point is not possible as these are controlled by another group and the existing allocation is now used up.
I have a Belkin N Wireless Router Model F5D8236, which has served my laptop with wireless and my wifes desktop computer through a ethernet cable for the last year.Recently we had to move her computer to another room so I got a Usb Wireless adapterNow when I try to connect her desktop to the network it says the settings do not match, or when prompeted for the PSK, it says its wrong, even though I'm dead sure I put it in right.I've tried transferring a copy of the settings with a flash drive, I tried resetting the router a dozen times, and all the wp2 settings.The USB adapter works, because when I turn the security feature off on the router, suddenly it can connect to the network.
View 1 Replies View RelatedI have a Netgear WNR612 wireless router, which worked fine for a few weeks. Then something happened and I can't keep the connection anymore. It happened right after I used iTunes to update my iPhone, perhaps a coincidence, but I'm mentioning that just in case. Internet still works fine with ethernet cable straight from the computer, only the wireless connection doesn't work. This happened about a month ago and I haven't been at home much to fix the problem. I have turned off and unplugged everything for several days at a time while gone. I get a Network Error message saying, Windows has detected an IP address conflict. I have tried restoring the router back to factory settings and reinstalling the wireless card. I have tried changing the IP address settings both in the Network and Sharing Center and the router admin page. What I think I should do is change the IP address in Command Prompt, but when I type "ipconfig /release", it says "No operation can be performed on Wireless Network Connection 2 while it has its media disconnected" and the same for Local Area Connection. I don't understand what this means, because there is a wireless key in my keyboard and there is a white light (not orange) like there should be. Also in the Network and Sharing Center, I can see that the connections are enabled.
View 14 Replies View RelatedI had a power outage while online and when power resumed, I was no longer able to connect to the internet via my wireless router. My laptops (I have 2, work and personal) both receive the wireless signal from my router (a Linksys WRT54GC) but I get a 'DNS lookup failed' error message when trying to access the internet. My standard set up was Arris cable modem-->Linksys router-->Laptop but I've had to go cable modem-->Laptop via Ethernet in order to access the internet.
Both laptops are running WinXP Pro, SP3 and I ran 'ipconfig/all' on my work one, once when connected via Ethernet and once when I had my wireless connection enabled (but again, not connected to the internet). Results below.
Ipconfig/all when connected via Ethernet to cable modem:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsm03015a>ipconfig/all
[Code].....
My neighbour n myself are using a shared internet connection. The modem is situated in his house and I have connected to that modem using a LAN cable, which comes to my house. That LAN cable goes into my WiFi router (through which I use the internet connection). I use a Lap and my neighbour a Desktop, he's receiving a "IP address conflict error" in his system, due to which his internet connection is getting disrupted. If I don't use my Wifi router and connect directly through the LAN cable he does not face any problem. But I need my router back?
View 2 Replies View RelatedI have a Netgear DG834PN Router. Connected to it usually are 2-3 laptops (XP, Vista, 7) wirelessly, a Xbox 360 and Win 7 PC via cables, a wireless printer and often an iPod touch, however PS3s, mobile phones etc are connected occasionally.
It had been functionally normally.until we changed ISP after ours was taken over (we didn't change but the provider obviously now has). However, since then (1st Feb) we've been having connection issues, probably an IP address conflict where items can access the router but not the internet.
The iPod and Xbox sometimes don't connect, as do the laptops often after been powered up from a sleep. Yesterday, when powering up one of the laptops, I got an IP address conflict message. Restarting the router sometimes works, but mostly it allows one device on and not another.
The printer has a static IP address (192.168.0.4) that I had to set up to get it working, but this has been active for months now without issue. I've had a look in the router settings and it's set up for DHCP as default with IP addresses from 192.168.0.2 to 192.168.0.254 so I don't understand why it has this issue suddenly. I had a look at the connected devices list, and everything appeared to have its own IP address.
Im setting up SBS 2011 in a new office. From what I understand, SBS 2011 needs to be the network DHCP server for everything to run well under Active Directory. The conflict is with a FIOS router, that also �needs� to be the DHCP server in order to communicate with a set-top box (MOCA bridge.) Verizon lists a handful of network configurations with multiple routers that might work, although completely unsupported. Is it possible for router, SBS2011, and set-top box to coexist in harmony on the same network (preferably keeping DHCP server on the SBS box)?
View 5 Replies View Related