i have a wrt54gc router. I can connect to the interent without no problems what so ever, however, i try and play a game on line and it tells me it cannot connect to the EA server. My psp is running v3.03. and the router 1.001
View 3 RepliesIs it possible to connect WRT54GC with telnet?
View 3 Replies View RelatedWe are trying to connect to Internet with the PSP.We are using the Linksys WRT54GC wireless router.Went to192.168.1.1to access the settings, everything has been set to disable security featuresPSP Version 2.6Followed instrutions from a web site including setting the DNS to 67.171.70.72 on the PSPThere is no WEP, WPA or any other security codes.I just disabled Firewall in the Security ModeSPI Firewall Protection: Block Anonymous Internet Requests:It is our own home network of two computers and any one else who has a wireless card can access.had a signal strength of 100% on the PSP.But, still got message..... A connection error has occurred A connection to the access point could not be established, check the security settings for the network and try again.how to connect to the Internet using the Linksys WRT54GC?
View 9 Replies View RelatedWhen I connect router correctly via modem I get message not connected no matter what I do I am convinced I am doing nothing wrong having used linksys router a number of times before about 2 years ago using XP cannot. I am now connected to router now to get on internet to this site
View 1 Replies View Relatedim using linksys broadband router model no WRT54GC firmware version 1.06....im using it since 2005 still now i didn't face any problem, but since 3days im facing a problem all of a sudden. i.e im unable to connect through Ethernet port ( through lan wire) to my PC, but i can access router through wifi.when i connect through wifi it is saying that there is no internet access. but i can access my router administration.i cross checked with another pc and another connecting cable , but same problem, no use i also tried resetting my router, updated my firmware. no use.
View 1 Replies View RelatedI borrowed a linksys wireless broadband router from my uncle and tried to connect it to my pc.But it is not connecting..i mean i connected an ethernet cable to my router to pc and waited for the light on the modem to become stable..and tried to go to ip address 192.168.1.1..the page not opening....it shows THE WEBPAGE NOT AVAILABLE ...but it worked perfectly for my unclE...eventhough i disconnected power cable and tried resetting but it is of no use ROUTER MODEL NO.WRT54GC ver 2.0?
View 1 Replies View RelatedI have a WRT54GC v2.0, that was working perfectly till yesterday.I cannot access the router no more, either thru cable nor wireless, all lights are flashing.I thought it would be the power source but i have measured it with my fluke multimeter and there is 3.5v, it is probably working well.
View 9 Replies View RelatedI put a password on my WRT54GC ver 2.0. After that i couldn't access internet. It keeps authenticating and never connects.
View 2 Replies View RelatedI have just got viasat internet from England to replace the local internet here in Spain. I believe that My router was programmed to the old internet and wont recognize my new modem. I have tried live chat and got guided thru a few things and established an IP conflict, but lost contact before we found a solution.
View 1 Replies View RelatedI've been using WRT54GC for over 3 months, but about two weeks ago I started to experience some strange behavior. About every day connection slows down to a few kbytes/sec (less than dial-up). Ping to comcast.net (my ISP) shows about 50% pings timeouted, 40% pings 50ms and 10% pings about 1 sec. Rebooting router works, but only for a few hours.I replaced the modem with a different model - it didn't work, so it's not the modem. I removed router and connected directly - no slowdown occurs any more, so it's not the computer. I am running latest firmware.
View 7 Replies View RelatedI Have a Linksys WRT54GC router which I use as a switch. Recently I have been able to connect to the wireless connection, but I can't access the router or the internet. Computers that are using it as a switch have no problems, but they are setup with different network details.
I know that wireless is on, I have also tried pressing the reset button and wireless still doesn't work.
Is there any firmware update for this product? I'm not hable to find it... Product: WRT54GC Version 2.0 (wwith external anthena)
View 9 Replies View RelatedI've been using my Linksys WRT54GC for couple years now, and only recently have I started to have significant issues with the device. I'm using a 2012 Macbook Pro, and my internet connection seems to be randomly dropping every now and then. Sometimes it works just fine for couple of hours only dropping once or so, sometimes it starts dropping literally every few seconds. What I usually do is quickly restart my wifi and the connection comes back right away. I also tried not doing that, and the internet connection tends to come back up after a minute or so.
I have read countless topics, also tried many things: changing MTU, the thresholds in router settings, security modes (it seemed to have worked fine after I changed it to WPA, not anymore though. I'm using no password now and it doesn't fix the problem either), changing the channel (my strongest signals around are on channel 1 and 11, thus I left mine on 6), I even reset the router today (held the reset button for 10 seconds~) but it didn't work either. I didn't upgrade the software since I heard stories about the software available on this site being corrupted or something, bricking the router, which is the last thing I'd want (I'm running on 1.00.7 now).
I have the impression (but it's just an impression, it might as well not be the case, and just me trying to find out when it happens, since it's not always that it breaks the connection while doing that) that it breaks the connection on high load, I mean when I'm for example using skype and facebook, and then try to go on reddit at the same time - the reddit webpage won't load, and the connection is lost after few seconds. But it also started dropping every few seconds while I was playing an online game and skyping at the same time today, which isn't a particularly huge problem for a 23Mbps download and 1.5 upload speed internet I suppose, and which it never did before. I have never had such issues with my PC using a Linksys USB adapter. The connection would drop from time to time when, for example, accidentally going on pages with lots of thumbnail pictures, or trying to load 15 tabs of jpgs at the same time, it was never that much of a problem really though, I just thought it's normal.
I'm trying to change my wireless router from WRT54G which been using for more than 5 years to a WRT54GC which I got from my friend. I clone every entry from WRT54G to the new one, even MAC address. Below is what I captured from the old router WRT54G when it connected through PPPoE
Login Type : PPPoE Login Status : Connected IP Address : 114.91.200.128 Subnet Mask : 255.255.255.255 Default Gateway : 124.74.12.242 DNS 1 : 180.168.255.118 DNS 2 : 116.228.111.18 DNS 3 : MTU : 1492 from the web admin interface, I can ping and traceroute yahoo.com, so can I browse any website from my PC.
and here is what I captured from the new router WRT54GC when it connected through PPPoE
Connection Type: PPPoEIP Address: 180.158.83.182Subnet Mask: 255.255.0.0Default Gateway: DNS1: 180.168.255.118DNS2: 116.228.111.18 from the web admin interface, I can ping and traceroute yahoo.com, but I cannot browse any website from my PC.
im triyng to forward a port but when i click save settings it give me a message: "Entry 10: Invalid IP Address".
View 9 Replies View RelatedI have used the WRT54GC (v2.0) router for a few years now, everything worked as smooth as butter, but a few days ago it just stopped detecting the internet connection. Everything works fine with the modem. After resetting the router, I tried to reinstall everything using the setup wizard but at the eleventh step, a pop-up message appears saying that it is "unable to detect the Internet connection" and, like I said previously, the modem works just fine. The username and password for the connection are correct (connection type: PPPoE).
View 4 Replies View RelatedWhen I run the setup CD the router cannot locate the internet connection. I'm using a Motorola Surfboard modem. My local PC works fine on the internet. My remote wireless PC shows limited or no connectivity. I have switched out the Ethernet cables with no luck
View 5 Replies View RelatedI updated the Firmware...then the WRT54GC can't work now,it's power led green and red always,I can't ping 192.168.1.1 via wired or wireless.wireless led shutdown.my laptop can't find any wireless network.
View 9 Replies View Relatedhow to change the time zone, the current time always show Firmware Version:1.01.6Current Time:Sat, 1-Jan-2000 00:08:40 and can't connect PPPOE
View 1 Replies View RelatedMy wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies View RelatedI am currently using a Thomson SpeedTouch ST780WLT router, which is working perfectly.I've got a second router currently not in use, a Linksys WRT54GC, that I want to set up as a simple switch to extend my network by a few ports.I connect the Linksys to my main router using LAN-LAN. Then I set up the linksys to have the IP 10.0.0.139 (my main router's IP is 10.0.0.138) and DNS to 10.0.0.138 etc.I've turned off both DHCP and WLAN on the linksys, to use it as a simple lan switch.
View 2 Replies View RelatedI had a power outage while online and when power resumed, I was no longer able to connect to the internet via my wireless router. My laptops (I have 2, work and personal) both receive the wireless signal from my router (a Linksys WRT54GC) but I get a 'DNS lookup failed' error message when trying to access the internet. My standard set up was Arris cable modem-->Linksys router-->Laptop but I've had to go cable modem-->Laptop via Ethernet in order to access the internet.
Both laptops are running WinXP Pro, SP3 and I ran 'ipconfig/all' on my work one, once when connected via Ethernet and once when I had my wireless connection enabled (but again, not connected to the internet). Results below.
Ipconfig/all when connected via Ethernet to cable modem:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsm03015a>ipconfig/all
[Code].....
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I just upgrade to 3.13.12 Build 120405 Rel.33996n firmware, because i need FTP server function.I did as on this site[url]..
All of a sudden, I could not connect to the Internet. I kept getting error message "Can't connect to DNS server", or similar. I have an ATT/Yahoo account, Speed stream 5360 Modem and WRT160Nv3 router. All was working well until yesterday. I was finally able to speak to an ATT Tech today, and he guided me through several troubleshooting actions and we were finally able to connect just using the modem. But when I connect the router, the network works, but I can't connect to the Internet. If I disconnect the router, I can access the Internet. None of my settings has changed. I saved router settings on my computer, and have compared them; all the same. The tech finally said it could be the blue cable from router to computer, or the router. So I'm hoping for troubleshooting before I buy another cable and/or router.
View 1 Replies View RelatedI have an E1500 N300 Router, I've had it for 3 or 4 weeks now. Ever since I've had it, I can no longer send e-mails out with Eudora nor Outlook. I've tried using about 3 different SMTP's just to verify that it wasn't a server issue. I tried Port Forwarding in the router settings. I selected SMTP and POP3 and checked Enable on both, then save changes. But they don't appear to be taking, as when I go back in and try to set them again, it let's me and doesn't give me a Port Overlap warning. I've been told that I shouldn't need to mess with Port Forwarding at all, I just need to go into the Firewall settings and open up the SMTP, POP3, and IMAP ports. However, I don't see any settings in my Router settings to allow this, aside from Port Forwarding and it's not actually saving the changes. I will admit, I'm not all that great with this stuff, and this is the first time I've had any issues with a Router stopping me from E-mailing.
View 9 Replies View RelatedConnecting E4200 media server (external hard drive connected to USB in router) to PS3.mapped External HD to media server folder. and enabled UPnP Media Server. after trying all options I can't see media server in PS3.
View 6 Replies View RelatedI have a Linksys WRT350N which I am trying to use an app on my iPhone to connect to my server using the public/external IP of my cable modem. I have the necessary ports opened and also tried adding the server to the DMZ but no matter what I can not get the app to connect to my server via my external IP when I am on my WiFi. I can connect without any problems if I use the NATed IP on the server when my phone is connected to the WiFi. It also works fine connecting to the external IP if I am on any other WiFi or the cellular network (which shows ports are forwarded correctly). I just can't connect to the server when I use the external IP and I am on my WiFi network. This is annoying as I need to keep changing the app's settings back and forth between the external and internal IP whenever I am home or away. I am left thinking this is some kind of issue with the WRT350N not allowing local internal traffic to reach the external IP. Any way to resolve this, maybe by entering a static route?
View 2 Replies View RelatedSince I have installed my new router, a Linksys EA6500, I have many problems to connect to my Exchange Server, which is located in my house, via Wifi. I tried to synchronize my Iphone and my Samsung tablet but it won't work. Most of the times I get the message that the Exchange server cannot be connected. When I turn off my Wifi en connect via my mobile provider I have no problems. When I am on a third party wifi I also can connect my server. Seems my own wifi causes lots of problems.
View 6 Replies View RelatedI have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies View RelatedI purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server. I click them and nothing happens.Also, the Cisco light on the router keeps blinking.
View 5 Replies View RelatedI cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
View 1 Replies View RelatedMy DIR-655 is setup and working fine with WPA personal encryption to different laptops in my home network. Question: Can I connect a wireless print server (LinkSys WPS54GU2) that only supports 'G' wireless encryption? Can the DIR-655 support a mixed N and G network?Do I have to reconfigure my DIR-655 to the slower WEP encryption and create an entirely 'G' network to include one G network device?
View 1 Replies View RelatedFew months ago I have bought Linksys E900 N300 router and its working fine. I also have a USB printer (make: Canon LBP2900) and Laptop (make:Lenovo G580). I want to make this printer wireless and through my laptop and router I want to give prints to this printer. Is it possible to do like this?
View 2 Replies View Related