I have a new laptop, an HP 2000, with windows 7. My setup CD is 500 miles away buried in boxes in storage, and both the other computers I had the router on before have died..and I need to go wireless tomorrow. I have a Cisco linksys router with no CD. I followed some steps posted in another closed thread but the password for the IP page was not accepted, and there is no username. Is this info outdated?I need to go wireless ASAP.
View 9 Repliesi have a Linksys modem BEFSR81 v.3 and am trying to reset my wifi password for secure connection. When i log into the the admin page, to my surprise, I could not find the security feature to create WPA or WEP password. i'm stumped. This has never occurred to me before on this modem.
View 6 Replies View RelatedI'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies View RelatedI decided to limit some Internet time for the kids going off this router (which has been working great since set up) but my Access Restrictions tab is missing. I have an identical router at my work place, same version/firmware, same settings, but the one at work does have the tab.
View 6 Replies View RelatedI am trying to use the Parental Control feature. I can't use Cisco Connect as there currently isn't an update for this router for Mac OSX Lion The firmware version in the support site hasn't been updated for ages, and I am running the latest (v 1.0.04) The Parental control tab, that is supposed to appear in the web browser interface isn't there. It's supposed to be, but doesn't show up.
View 5 Replies View RelatedI currently have a E3000 router. I have set up a shared USB drive successfully through this router. After a couple of months, I needed to re-locate my router into a different room. After doing so, I plug back in the USB drive and cannot access it. If I go through the GUI, it tells me that the drive type is not supported, and if I just plug it into a computer to obtain the infromation off of it, I get a "drive is corrupted" error
View 5 Replies View RelatedI recently installed a WRT54G wireless router however I has this same question about my BEFSX41 Wired router.
View 9 Replies View RelatedI 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
View 5 Replies View RelatedI have a BEFSR41 ver 4.3 and I upgraded my firmware to 2.00.4.8 from within the router. Had a problem with the flashing power light. Resolved the issue after reading another post on this forum using the TFTP utility. Now, however, if I go into either Port Forwarding or Port Triggering and change anything, there is no Save Changes button to click on in either page. They are missing. If I click away, or close the browser and come back, all changes I made are lost. I have tried reloading the firmware at least four times. I've powered off, pressed the reset button and any combination of these that you can reasonably think of. The buttons are gone! I have tried accessing the router from both IE and Firefox, accessing the router from all the machines on my network, to no avail. Everything was working fine before the upgrade, of course. The router does not have the option to save the old firmware before any upgrades are made. The original firmware has been overwritten so I can't go back to it.
View 2 Replies View RelatedFollowing the chat with the technical support of CISCO.In few words, the LINKSYS X3000 is the only router in the world that can't shows the DSL line parameters ( SNR and LINE ATTENIATION ) so you can't evaluate the line quality without using another router.... INCREDIBLE!!!!Let's see how long it will be before the firmware update!Me: simple question: is rather embarrassing but I can't find the SNR value (Adsl status) in the Linksys X3000 interface. Same for the Line Attenuation values. These are the standard DSL information and they are essential to evaluate the DSL line quality.Unfortunately, you are right, these parameters are not available on the Gateway (X3000) Setup page.Me:It's unbelievable I use routers for my work and this is the first product that can't shows the DSL line parameters...The only parameters available under DSL Connection Subta are Status, Downstream Rate and Upstream Rate.Me:Do you think it's serious? The price of this product and the target to which it is oriented suggest a more professional approach.I agree, but as of now, this is how it is however, you need to keep an eye on future updates for the device that might include these paraters/features.Me:Please could you send a notification to the DEVELOP TEAM to quickly update this product FIRMWARE and close the gap that separates it from other products in the same category?
View 9 Replies View Relatedget the network key to connect with my Linksys WAP546 v 2 for my new laptop. Without this key it's not possible to make wireless contact
View 1 Replies View RelatedI just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies View RelatedDo I need to do anything to get the linksys router to interface with motorola dsl modem?
View 1 Replies View RelatedWhen I type the routers IP address in teh brower window, nothing happens so I cannot access the router setup. I have a WRT110. What am I missing. I was able to do that when I first setup the router.
View 9 Replies View Relatedfor the past couple of hours i've been trying to setup my router (Linksys WRT160N).When i set up all the cables, like it is in this picture:
[URL]....
I get internet through my Desktop using a wifi card that picks up the internet from my in-laws across the street (gets a really good signal btw). Anyway, that connection is perfectly fine, and up until recently I had been using a Hawking Range Extender to repeat the signal through my house connecting it to my PC's ethernet port and using the Internet Connection Sharing feature. For some reason that is beyond me it suddenly stopped working. Or rather, it will work for a couple minutes and then stop receiving packets.I'm thinking the device is faulty since it never actually worked that great to begin with. Is this type of setup possible for a wireless Router such as a lynksys device? Or would I need a repeater/range extender like I have been using?Again I would use the Wifi from my PC to share the connection with the Router to broadcast that signal through my house.
View 6 Replies View RelatedI am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
I have a phone system which uses a 10.40.x.x network and a LAN using a 10.1.x.x network. I'd like to pass the traffice from the 10.40 netork over to the 10.1 network so I can use data (caller id for example) om my PC network.I have an old WRT310. How to setup teh wrt310 so that I can have it pass data from teh 10.40 network over to a specific IP address ie 10.1.110.110?
View 4 Replies View RelatedI am trying to setup a WAP with my linksys 2500. I am currently using a Gateway connected to my DSL and am looking to set up the access point through the E2500.
View 1 Replies View RelatedI have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.
View 4 Replies View RelatedI can setup my router with the cd
View 1 Replies View RelatedI'm using an Static IP adress and i'm using wrt120n router, but to connect the internet i have plugged the internet cable in the 1,2,3,4 (doesn't matter which one) slot. So now i'm just using the wirelss part of the router without "routering" if i can say so. When i put the internet cable in the Internet slot of the router, the laptop just cant connect to internet - it shows Unidentified network without Internet Access. I don't know what type of changes i have to make in the WEB interface of the router. I think i have to set the type of the connection - now is DHCP and may be to put my IP adress, DNS, Subnet mask in the router settings, but don't know how exactly. I've tried to set up the router with the CD-interface but same thing happened - Unidentified network when the cable is plugged in the Internet (yellow) port. How to set up the router to be a router, not just a wireless switch?
View 9 Replies View RelatedI'm trying to set up my E1000 router and when I run the Cisco Connect software that came with the router I get a message that says that it can't find the router, I've tried running it with my computer connected to the router and not connected. I've looked through the FAQ section and didn't really find anything. I'm trying to set it up on a laptop, it's a Vaio running Windows 7, I don't if that makes any difference.
View 7 Replies View RelatedA linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n
All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3)
Current WAN Configuration:
Encapsulation: RFC 2364 PPPoA
Multiplexing: VC
QoS type: UBR
DSL modulation: MultiMode
[Code].....
I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose.
Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network.
What I need:
I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). How do I do that? Or maybe an alternative?
I have been attempting to set up a linksys wireless-n e1200 router on my hp p6-2007c (Windows 7 SP1, 64-bit) desktop pc for the last day and have exhausted everything i can think of. The previous router was a linksys WRT54G and it worked fine. However, upon setting up this new router i get a "no internet access" message accompanied by the little yellow triangle and the ability to still connect to my router via its ip address to alter its configuration. The connection status for the network and the internet is identical for all the laptops in my house. I originally attempted setting up the router using Cisco's setup program. At its conclusion, the setup program informs me that i am connected to the router, but my internet connection has been lost (even though it was never there) I have tried starting over from scratch by resetting the router back to its default settings and using a variety of different channels (Auto, 1, 6, and 11), frequencies, etc. I have uninstalled norton antivirus, disarmed the windows security programs, made sure of TCP/IP settings, rolled back, uninstalled, and finally updated firmware, uninstalled/reinstalled driver for wireless card, disabled/enabled the card itself, deleted all other previous network profiles still present in the "Manage Wireless Networks" screen, and probably some other suggestions i came across in this forum. They all failed with the same results, i.e. the ability to connect to the network locally and having no internet access.
View 1 Replies View RelatedCannot connect to Linksys Router 192.168.1.1 Webpage, do not get login setup screen.
View 1 Replies View RelatedHow do I make my home network secure. I am with virgin media and have a Linksys Router
View 1 Replies View RelatedCan I use a second linksys wireless router as an access point and can I connect a wired computer to one of its ports?
View 1 Replies View RelatedI am using 3G to access the internet on my PC. I have a 3G modem connected, and want to setup my Linksys WRT54GL router to enable wi-fi, so other devices can access the internet as well.
View 7 Replies View RelatedI had my router settings in a file on my hard drive so I would not lose them. Just my luck, my hard drive took a giant dump and the restore did not restore 100% and guess which file was among the missing?So I've followed about 15 different "reset" instructions which includes holding the reset button for 10-60 seconds; unplugging the router afterwards for anywhere from immediate to 60 seconds. Obviously, none of those sets of "sage" advice had any influence whatsoever on my router. My "server" is of my own creation:
Core2 Quad Q9550;
8 GB PC28500;
Gigabyte GA-EP45-UD3R;
Windows 7 Ultimate 64 bit SP1.
Cable Modem RCA DCM425.
I can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
View 1 Replies View RelatedHow do I setup a E3200 router using a wireless USB modem to connect to the internet? This is my only choice, I do not have a wired connection and I do not own the telephone wires and there is no permission to do otherwise.
View 3 Replies View RelatedI replaced a WRT120N router with a new one thinking that the old one was damaged. During setup, the router wasn't recognized. I used the same connection for a line from the internet to my LAN connectin and the line works fine. Connecting through the router is no good.
View 1 Replies View Related