Motorola SB6120 DOCSIS 3.0 Ethernet Cable?
Sep 3, 2011
I just got a Motorola SB6120 SURFboard DOCSIS 3.0 eXtreme Broadband Cable Modem and the box didn't came with the Ethernet cable inside to connected to my router .Now... I been reading in some places that it came with a (Patch cable) and in the User guide it says ( Ethernet cable) and then I found out that it says ( Interfaces 1 x Modem - F connector,1 x Network - Ethernet 10Base-T/100Base-TX/1000Base-T - RJ-45 ) So ... I found that, that kind of Ethernet cable it's a "crossover cable" So...I'm a bit confused here now .I read that this kind of cable it's a "Cat 5e(nhanced) cable" ; But ......it's not as fast as a Cat 6 cable.
View 5 Replies
ADVERTISEMENT
Sep 18, 2011
I was working with Motorola SB6120 cable modem regarding an odd power cycle issue (it would power cycle randomly for 24 hours). While trying to diag the issue, I was taking a peak in his router config and found a port set to forward as:
Application: Comcast
Port From: 888
Protocol: Both
IP: 192.168.100.1
Port To: 80
I understand that his modem admin page is now available from the internet. He said his friend set this up to "modem", but I don't see any advantage of having this done. At this point what are the other advantages of forwarding such ports?Another key note: When the port forwarding was disabled, suddenly the power cycle issues stopped.
View 3 Replies
View Related
Jun 22, 2011
I can't get my PC to connect to my broadband. I am running windows 7 64 bit and use the following:
Motorola Surfboard SB6120 modem;
NetGear WGR614 wireless router
I am able to connect with other devices (iPhone, Roku) to my wireless through the wireless router. My computer recognizes the broadband connection, but it won't connect to it. I get two errors when I try to connect:651: the modem has reported an error, and 638: the remote server is not responding in a timely fashion.I have tried connecting the ethernet cable directly to the modem, but I get the same results.Also, I have tried to cycle down the computer, router, then modem and turn them back on in reverse with no change in results.The connection worked until I clicked "disable connection" one day when I had trouble connecting (high traffic i think). Since then, the"home group" I set up originally with the connection wizard disappeared, and it had not been able to connect since then. When I try to connect I click on a small icon in the lower right that says, "not connected, connection available", then I click on the button to connect to broadband and get the errors described above.
View 3 Replies
View Related
Oct 19, 2011
So I just noticed on my Cable modem the link light is blinking orange, per Motorola if its blinking orange - Computer is connected via a 10 mbps or 100 mbps Ethernet port.
On the Linksys E4200 status page it says
Internet Port Speed:
Internet 10/100 mbps
Local Port Speed Port 1 - 1Gbps
Maybe I just noticed this with this router, but I'm pretty sure this didn't start happening until I updated to 1.0.03.
Previously the link light was blue indicating a 1Gbps connection.
View 4 Replies
View Related
Dec 22, 2010
1. Our Motorola SB6120 popped out of existence today; FYI, this was plugged into a brand new APC UPS unit (which does not have coax/cable suppression features).
2. Previously (past days), one interesting thing I have noticed is excessive amounts of distasteful electrostatic shock when working in the closet and touching the metal bearings of the cable & wires. Is the cable not grounded properly, and is it the cause of #1?
Recommend me a surge protector/suppressor strictly for cable (do not need outlets/ethernet/rj45/etc).
View 3 Replies
View Related
Aug 12, 2011
I want to connect to the Internet small office where docsis (internet over tv cable) is used as WAN.For similar tasks but other WANs (adsl, dial-up) I used 800 series. But now I can't find anything in this series to solve my issue. There is 815 but it has no wi-fi.
I can use cable modem that my ISP gave to me: this modem acts as bridge so I can use router with FE-based WAN but it is better to have one device instead of two.
View 3 Replies
View Related
Apr 28, 2013
Is there a difference in an ethernet cable and an Ethernet networking cable? I have an Ethernet cable and a 6 port splitter I am trying to connect. I have 4 ports in the router that are in use. When I connect them to the splitter nothing s working.
View 1 Replies
View Related
Feb 13, 2012
I've been trying to connect my D-Link DIR-601 router with a Motorola SBG901 cable modem. The modem itself has a built-in WIFI (G) and one ethernet port, but not good enough for my purposes. I need more wired connections and an (N) WIFI connection, which the D-Link could provide, if I could get it to work. I just cannot get the two pieces of equipment to talk to each other. I can set up 2 independent LAN's, but no WAN (internet connection) from either. D-Link has provided pages of instrutions, but nothing works.
View 1 Replies
View Related
Aug 18, 2012
My Motorola SB6121 DOCSIS 3 modem is connected to a Medialink n-band router. Sometime in the morning (usually between 7am and 9am, the router loses the ability to see the modem. I can access the router's control panel, and I see 0.0.0.0 for WAN IP, Subnet Mask, and Gateway. Primary and Secondary DNS server are both blank. Connection Mode is Dynamic IP.I lose the ability to access the modem's control panel directly (192.168.100.1), even though the PC I use is hardwired to the router. So, I unplug the modem, unplug the router, wait, plug in the modem, plug in the router, and everything works again.I've had more than twelve service calls. Every Charter tech looks at the line, puts in boosters, takes out boosters, replaces splitters, and seems to only look at signal. I've BEGGED Charter to let me speak to an engineer, because my suspicion is that it's something to do with the DHCP server.
I did, by the way, replace EVERYTHING.I have had 5 different modems...same problem. I have had 5 different routers...same problem, including a modem/router combo.I've tried different brands, too.I've disconnected all wifi devices from the router, and rebuilt my PC's operating system. I've even unplugged the refrigerator, because one Charter tech claimed it was "upstream noise."I've been online only a few times when the system actually goes down. What I notice in the router logs is this: [code] So at 9:34, no ranging response - T3 timeout, followed by Unicast Ranging Received Abort Response;
then the Cable Modem Reboot due to T4 timeout, and the system time goes to 1/1/1970 at midnight. No ToD.
The last piece of information: Charter installed a second modem as a "test." That was originally in the same room. A month ago they did another line from the box directly to the test modem to skip the splitter on the house.That modem shows the same problems, EXCEPT -- not perfectly in sync. I might see the same error, but the time will be a few minutes and seconds off. And sometimes I'll see the errors, but the modem won't go down.Sometimes the first modem goes down, sometimes the second. I'm accustomed to a router "healing" itself when the modem goes down.It might be off for a bit, but then will re-establish. This Medialink doesn't do that. It forces a physical restart every day. There are other outages too, and all I get from Charter is "the signal strength is good."
View 3 Replies
View Related
Jan 6, 2012
Would this work ?. also, on the back of the modem is a rectangular, not the typical, usb slot. I cannot move the modem because it is connected to the wall. I don't want to use an extra long wire either. What do I need to buy so I can use the wired modem, as a wireless one on my pc downstairs ?
View 6 Replies
View Related
Jan 11, 2013
I am looking for a router or something else that still allows me to connect my phone line to my router or computer so people in the house can make calls. My cable modem is a Motorola SBV5120 I had it for eight years now and I am thinking of switching our network to wireless so I don't get those cluttered wires.
View 1 Replies
View Related
Mar 19, 2012
Trying to figure out if I have a bad modem or bad wiring leading to the modem.I'm losing connectivity usually in the evening when I'm sure everything is more loaded.he reason I'm concerned about the modem is that when I lose connectivity, I can't access the modem through my browser. It won't respond. This isn't just for a moment. I'll unplug the modem and plug it back in. I can access the modem after that with my browser, but more often than not, I don't regain connectivity. It keeps trying and failiing.its a Motorola SB5100 from 10 years ago. how to seperate bad wiring from a bad modem?
View 4 Replies
View Related
Apr 22, 2012
I have a 192.168.1.xxx network connected to Verizon FIOS via Actiontec MOCA / router. I also have a 192.168.15.xxx network connected to Comcast via Motorola VT2442 router (used for Vonage) and a Motorola SB6121 cable modem.
Each network has it's own gigabit switch connected to each router. The two networks are physically separated but switches and routers are physically side by side.
What is the best configuration to allow devices on 192.168.1.xxx network to communicate with devices on the 192.168.15.xxx network (share printers, NAS, etc), but still have each network served by it's respective ISP, and each device still get it's dhcp, dns, gateway, etc from each respective router?
View 6 Replies
View Related
Nov 7, 2012
Today I purchased a Motorola SURFboard extreme Cable Modem DOCSIS 3.0 in order to replace my old modem which is out of date and has been very slow as of late. I connected the coaxial cable, Ethernet cable(to Linksys wireless router), and power expecting it to simply work. All four lights came on green (power, downstream, upstream, connectivity). The downstream light turned blue which indicates a bonded connection.The device light was blinking on the modem. I connected to my wireless router, but no internet access. I then tried connecting my laptop to the modem directly via Ethernet cable, still no access. I think that rules out the router being the problem. I also ruled out my laptop being the problem as the same thing is occurring with my other laptop and desktop. I called my ISP (Cox Cable) and had them re-establish connection with my modem, this did nothing. I thought for sure this meant I had purchased a faulty modem; I hooked up my old modem and the results were the same, the modem connected fully with no problem (all four lights were green) but I have no internet access.
View 3 Replies
View Related
Sep 4, 2011
I have a Motorola modem SURFBoard SB4200, along with a wireless Linksys router that connects to that modem. The router works normally but the modem often dies and restarts itself after about 1-2 minutes.
What could be causing this problem? How should I start debugging it?
Could an excessive amount of network traffic be bringing down the modem? Are there any tools that can monitor the modem?
View 2 Replies
View Related
Aug 8, 2012
I am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies
View Related
Jun 10, 2011
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies
View Related
Mar 9, 2012
if my internet carrier supports both, why should I spend a little more to get a cable modem that has DOCSIS 3.0 support? What's the benefit over DOCSIS 2.0 (or 1.0)?
View 14 Replies
View Related
Feb 24, 2012
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
View 1 Replies
View Related
Apr 30, 2011
I have a Dell XPS M1530 with Vista 32 bit. When i plug in a cable i get nothing, no error, and the comp does not recognize that a cable has been plugged in. I think that this started after my Hard drive failed and Dell replaced it but i'm not positive. No errors (? or !) in Device Manager and I can't find the Marvell 88E80XX 10/100 Ethernet Controller in device manager. I have attempted to Reinstall the drivers. The wireless is still working. I have one Light to the right of the port that is on all the time solid but no flashing with the cable in or out.
View 14 Replies
View Related
Aug 15, 2011
i just recently upgraded to Road Runner Extreme which Uses DOCSIS 3.0 SBG6580 Modem and i was wondering what internal settings i should use to maximize my speeds and online gameplay. I'm running a Ethernet line into my Xbox360 and wireless for my laptop. Also, i was told that Road Runner Extreme would get me 35Mbps downstream and 5Mbps Upstream, yet these are the speed test's i'm getting [URL]
View 1 Replies
View Related
Feb 26, 2013
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
View 4 Replies
View Related
Aug 16, 2012
I have 1 EuroDocsis modem and 2x 1130AG wireless things.How do I manage to get this connected to each other wirelessly?The internet is allready configured at the EuroDocsis modem and I now want to distribute it wirelessly to both 1130AG's. The EuroDocsis is using WPA2 PSK.I read something about WDS, but I don't get that to work either.
View 1 Replies
View Related
Dec 19, 2012
My boss is been looking to expand his side business of trading online. He asked me to look into finding him the best and fast router possible that would give him the best speeds possible. He is currently using the asus black diamond router and the Motorola SB6120 modem but would like to know if there are better options, spending a few hundred on a router isnt a big deal. He also wants to know if there is anything else he can do with his pc, like network card or modem.
View 19 Replies
View Related
Jan 26, 2013
I'm trying to make the server work for minecraft and I have the port number for the port which is 25565.I just need to know where exactly to enter this information. I also know that the protocol is supposed to be set for both tcp/udp.
So basically I guess my question is, where exactly do I put the port number if the one given to me was 25565?
View 2 Replies
View Related
Oct 21, 2011
I called up the ISP and had him activate the Sb6120 modem.The Dir-655 will not link up with the Sb6120 unless I drop the WAN port speed down to 10MB. Then it will connect. (the light on the modem will come on). I thought the modem was bad so I had the ISP deactivate that one and we tried another Sb6120 samething.I did the firmware update on the Dir-655 to current but samething.
Firmware Version :1.35NA, 2010/11/12
View 4 Replies
View Related
Sep 18, 2012
Can I access my Motorola SB6120 SURFboard DOCSIS 3.0 eXtreme Broadband Cable Modem while remaining behind my pfSense router?
My LAN Subnet is 10.0.0.1-254.
View 4 Replies
View Related
Aug 4, 2012
I'm setting up Blast! Comcast/Xfinity internet (50mb/s) using an SB6120 modem and a linksys E3000 router. I haven't done anything yet, as i haven't received the modem in the mail yet, but i want to be prepared and knowledgeable when it all arrives. Here are my questions I've heard that running this router/modem setup on the N band at 5Ghz provides the best signal strength. How do i configure this? The main goal is to take advantage of as much of the 50mb/s as i can (i know this number is not practical due to overhead estimations etc).My newly built desktop has one free PCI-E slot (the other is occupied by my EVGA GTX 670) and 1 or 2 PCI slots. What's the best option to give my desktop wifi capabilities (pci card or usb adapter) in order to maximize signal strength? I'm about 10 feet away from the router, a door separates the computer from the router.
View 8 Replies
View Related
Jan 6, 2012
Just got cable and new hardware and been running bandwidth tests. I know wired is always going to be faster than wireless but was wondering if there were things I can do to see where the bottleneck is.
I have cable internet with a sb6120 modem and the asus rt-n56u router. When I go wired, I get 40+mbs down and when I go wireless I'm getting approx 20mbs down. Dont get me wrong, this is more than adequate but was wondering why the huge difference. I'm not anywhere close to the theoretical max.
The rt-n56u is on firmware 1.0.1.7f which is current. My desktop uses the WMP600n and my laptop has the Intel 5100 AGN built into it - both have updated firmwares.
View 12 Replies
View Related
Jul 21, 2011
I'm trying to set up a system where a lecturer can sit at home and give his (video and audio) class across the street via an ethernet cable strung across the street. The only problem is he has a mac, and we in the class running it aren't going to leave our PCs for macs!Is there any simple way to connect the mac to PC (without running through a router, as it slows down the system)?If so, what programs will work best for both PC and mac for streaming the video (and are free)[BTW I don't think a 100m cable is too long for the signal.
View 2 Replies
View Related
Dec 15, 2012
What is the best Ethernet cable too run around my house?
View 3 Replies
View Related
Mar 19, 2013
I'm switching from using a wireless usb adapter to a wired connection via ethernet cable.
When I plug the ethernet cable in however nothing happens, I've tried using it with a different computer and it works like a charm but this one doesn't seem to be working right.
HP Pro Small Form Factor 3010 Windows 7 32bit (Other computer was using windows vista)
Windows IP Configuration
Host Name . . . . . . . . . . . . : HPPro3010
Primary Dns Suffix . . . . . . . :
[Code]....
View 1 Replies
View Related
Sep 20, 2012
Yesterday I was on my computer when all of the sudden my internet stopped working. I am using windows 7 and at the bottom right I see a big "X" over the small computer icon. I already tried a computer reboot, a router+modem reboot, system restore, and I even reset the power to the room of the modem+router from the fuse box in my house. I tried everything.
I'm sure the problem must be from the actual cable or mother board itself. ( I hope it isn't ) I tried blowing out any dust from the ports and making sure that nothing was blocking the connection. I fell asleep last night with the internet not working, and woke up to it working. Every other computer in my house works except for mine. I tried all of the router ports as well. I did not attempt another ethernet cable though because my room is far and I would need to make a very long one.
View 14 Replies
View Related
