I an on this form from my cell right now.. so, the computer i want to get Online with is a desktop and i have been days with this problem.
View 14 RepliesI have a USB Netgear WN111v2 that has been working perfectly up until now, it can't connect to the network and trying to manually set up the addresses, reinstalling drivers, and trying a system restore haven't worked. Even though the router has a lease for the computer on 192.168.1.11 it's doesn't work, although it will show that it's connecting, it won't ping anything, including the router... WZC utility is stopped?
View 4 Replies View RelatedI connect to the internet using a wireless USB. I woke up this morning and the internet showed that it was connected yet it wouldn't allow me to open the web or anything such as "msngr" I took the wireless card out for a couple minutes and then tried. That didnt do anything but say acquiring network address. I am not that knowledgeable when it comes to computers but these are the things that I have tried so far :
I went into properties and configure USB . . Made sure that the SSID said "Any" I Also tried going into properties and tcp/IP internet protocol and made sure it was on obtain IP address automatically . Hmm I tried. RUN>SERVICES> to make sure that the DHCP and TCP were started and on Automatic. I then tried system restore :- (went back about 2 weeks) . . Nothing. I then tried RUN>CMD>IPCONFIG/RELEASE *ENTER* IPCONFIG/RENEW *ENTER*.
when I did that it showed wireless network is now connected, yet back to ground zero. It wont let me browse. Its not really connected. When I look at the connection status, signal strenghth is good. Packets sent & received are good. I feel like there is just something little that. I am not getting, that is making this happen.
I have fitted a thomson router to my desktop coputer using an ethernet cable and all is working fine. My Sony Vaio laptop recognises the wireless connection but fails to connect at the acquiring network address. I have been into the properties section of the network connection page and am only allowed 8 characters for the network key. But the Network key on the bottom of the modem is longer than 8 digits.
View 1 Replies View RelatedRecently, I am having an issue with my LAN connection. After I boot up, I get the "two computer" icon in my system tray that stays active. When I mouse over it, it says "Local Area Network Speed 100 Mbps Status - Acquiring Network Address"However, I am connected to the internet and there seems to be no connectivity problems. And it has an IP address: 192.168.1.66 This "acquiring network address" will persist forever, (although sometimes it will quit). If I right-click and do repair, the problem disappears immediately.I am running Win XP SP3 and am connected by ethernet cable to an ATT-U-verse Gateway.For what it's worth, Windows takes a very long time to boot up -- it takes a while for the icon to appear, and then the boot process completes.
View 1 Replies View RelatedI bought a Netgear WNA3100 wireless adapter today but when connecting, it says limited access after entering the SSID and the passphrase. I currently have windows 7.
View 2 Replies View RelatedI have a Dell Inspiron Mini 10 Netbook, when I'm trying to connect to a wireless network I get the message 'Acquring Network Address'. I can connect fine using a wired connection, but using the Wirless 1397 WLAN Mini card it won't connect.
I tried to log a call with Dell as the machine is only 2 months old and someone remotely connected and said it was a software fault not hardware and they would charge me to resolve the issue. I found that hard to swallow so thought I would try here.
my daughter accessed a website and got the XP Security 2012 virus on her laptop. Then she went on my pc and did the same thing. Fortunately, it appears that I have gotten both systems cleaned up. At this point my system seems to be fully functional, but her laptop is another story. It is working ok, except that we cannot connect to the internet/network with it. It seems to be stuck on the "acquiring network address" loop. I am not super computer savvy, but I have looked at the device manager for issues (found none).
View 1 Replies View RelatedRecently during the power failure my PC shut down abruptly since since then it is not connecting to the network. I have a cable broadband internet, I am using Ethernet wired connection, Intel PRO/100 VE. The Ethernet jack is good as I have confirmed using my laptop. The network connection gets stuck in acquiring network address state. I tried restoring the system to earlier date but it fails to restore. I installed new Intel drives, deleted ethernet adapter from device manager, reinstalled TCP/IP but no luck.. I am using XP SP3 on P4 machine,
View 10 Replies View RelatedI recently started a thread called 'Network Controller Not Found (clueless!)' which highlighted a problem I had with a RaLink Wireless Adapter and the system not locating the correct driver. It's now found the Ralink Wireless Turbo 802.11g driver and wireless connectivity is live. However I have a new problem with connecting to the BT Homehub. BT Fon and Openzone connections are fine, and it finds my BT homehub by name, but on clicking 'connect' I have a constant 'acquiring network address' over the icon in the system tray. I've seen this problem mentioned before, but am completely new to setting up wireless connections, so don't understand much of the terminology at all! Even when trying to reinstall from CD, the homehub is not indentified, resorting to wired setup. I've looked at other threads but just don't know where to begin. I've followed instructions and reset the homehub, but nothing. The IP address values are 0, is thing something to address (no pun intended)?
Here is a rundown of a wireless networking test.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Air
Primary Dns Suffix . . . . . . . :
[Code]......
I have a Asus EeePC SeaShell 1005HA-H and i have a LINKSY ROUTER in my home. I recently been having problems with my wireless internet. I know it isnt the router because i have went to my boyfriends house and my laptop usually automatically connects to his internet and the same message continues to show up "Acquiring Network Address message". I try to repair the network and a error comes up. Then i went to check the firewall settings and the firewall is tured off.
View 1 Replies View RelatedI was connected on wifi and all of a sudden I got disconnected and hasn't been able to connect since. This happened Sunday night and it's now Thursday. I got stuck on acquiring network address. I've been using the same wifi connection for about 7 months now and this never happened before.
All the other laptops at home (Mac and XP) could connect except me. I tried to google over my phone but still wasn't able to fix it.
This is what the ipconfig says:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
[Code].....
i have a dell inspiron mini 10 and i put windows xp pro sp2 on it and got all the neccesary drivers for it the problem with it is that it detects my router and everything but when it tries to connect it gets "stuck" on aquiring network adress i tried the winsock fix and everything but nothing seems to work
View 1 Replies View RelatedHave a computer running windows xp. Whenever I plug in my internet cable it says 'Acquiring Network Address'. I have left it for over and hour but it still says the same thing. I have connected other computers to the router with the same cable and they work perfectly. I have also tried channging the linkspeed for the network connection, renewing my ip address, repairing the network connection and disabling and enabling the connection.
View 2 Replies View RelatedI have a laptop HP Mini 110 1025DX with Windows XP sp3 Home Edition and up to January,31 his wifi was ok. Since February,1 my wifi keep on giving message âAcquiring Network Address on my work. I tried several possible solutions without success. My wireless card is Broadcom 802.11 b/g WLAN. His drive is updated. In my work, haven´t change none parameters from the wireless. What I need to do ?
View 2 Replies View Relatedi recently bought a dell mini laptop and i am already encountering problems with my wireless. i am on the laptop now, but i connected it via ethernet, and that is apparently working. whenever i hit repair it gets stuck at acquiring ip address.
View 4 Replies View RelatedI'm running a Windows XP Dell laptop. A few days ago I completely reformatted the computer because it was just starting to run slow. I reinstalled Windows from the factory CD and downloaded the latest drivers from Dell's website. Now suddenly, after the reformat, my network connection gets stuck on "Acquiring network address." Running ipconfig shows either 0.0.0.0 or a blank space for each field.Other laptops in the house work fine.I did discover that I can get it to say "Connected" if I go into the advanced settings and manually enter an IP address and use the subnet and gateway from my desktop's ipconfig results. The problem is that I can't actually get on the internet. It just says it's "connected."
View 14 Replies View RelatedMy Dell was running very slow, so I used the disks that came with the computer to reinstall Windows XP. After doing this, it wasn't detecting our wireless network. I went through on the drivers disk and installed the drivers in order according to Dell's specifications. It still wouldn't work, so I went to the dell website from another computer, and downloaded the drivers that pertained to the network. Now it is recognizing the network, I was able to enter my key, but it won't stop "acquiring network address". When I do the ipconfig /all, it looks like there is no IP address:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsUser>ipconfig /all
[Code].....
... and made a fundamental mistake of uninstalling adapters hastily without looking into it. Now when I try to re-install the adapters, I'm running into difficulties. Specifically, I don't have the CD-ROM I originally must have used, and the following message is popping up: "Files Needed - The file 'atl02_2k.sys' on Atlansic Fast Ethernet Adapter Installation Disk is needed. Type the path where the file is located and then click OK." Unfortunately, I don't have any idea if there is a path where this is located, so installation cannot complete.
The reason I took this option to begin with was that the wireless connection on my laptop [Asus, Windows XP] was acquiring network address without ever connecting fully to the internet. I had previously tried another of other methods, such as manually entering an IP address, to no avail.
A few days ago the internet on my desktop was working fine. now it has the 'limited or no connectivity' sign on it and i have done a few things to try and fix this. I started by trying a simple repair. it comes up with 'the following action can not be completed: Renewing your IP address' This lead me to try and restart my PC and router with no luck.
I then decided to look a bit further into it and went ito CMD and flushed the DNS. i then did 'ipconfig /release' which generated the response 'IP address for adapter wireless connection 9 has allready been released'. I then did 'ipconfig /renew' to which it generated an interestin response:
'An error occurred while renewing interface wireless network connection 9 : The RPC server is unavailable'
I have made sure my DNS client is on automatic, alont with my RPC (this was uneditable). Its not a router problem as i have had multiple devices connected before and my laptop is working just fine connecting wirelessly.
so ive tried just about everything, installing/uninstalling drivers, restarting stuff in cmd, but it still will NOT acquire [code]
View 15 Replies View RelatedMy computer was recently cured of a damaged processor and a viral infestation, and it seems to be working properly again, however,I've been unable to connect to my network because the connection gets stuck on "acquiring network address".I am running Windows XP service pack 3 and the network device that isn't connecting is a Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC.
View 2 Replies View RelatedI'm working on a friends laptop that used to connect wirelessly to their network no problem, and all of a sudden it would no longer connect at all. It a 5 year old Gateway laptop running Windows XP Media Center. It just hangs at "Acquiring network access" and never connects. I'm pretty sure it's their network because it works on my home network perfectly, connects and stays connected.
Can you give me some pointers to do to the laptop and/or the network? I normally would start fresh with the wireless network, but they have a bundle package of AT&T (internet, phone & TV all-in-one) so the router is branded AT&T and don't want to mess any of that up.
I have a Dell Latitude D620 and my wireless isn't working. It worked before but then I had a malware/spyware on my computer that blocked my wifi and when I managed to get the program off, my wifi still wouldn't connect. It's not the wireless card because I bought an external one and it did the same thing. It's not my router because my other computer connects to the internet.
View 1 Replies View RelatedI'm using is the Netgear WNDA3100v2.What happens is when I attempt to connect to the internet I have to reset the adapter multiple times before it even recognizes my internet. And then once that happens it takes a few more tries to actually connect. And when I'm connected the speed is fairly decent (around 15-30 Mbps). Problem is, every 5 minutes maybe even less, I disconnect. Then I have to go back through the process of restarting the adapter and whatnot until I reconnect. I've been dealing with this problem for a few months now and have neglected to post about it anywhere because I didn't think it to be this unique.
I have tried just about every other "solution" I could find on the problem and none have worked. Also, if this says anything, I have a laptop setup literally 1 foot or less from my desktop and it connects perfectly well and good using the same adapter. Also I recently purchased another adapter (Linksys AE3000). I figured this might solve my ailment but of course, the same thing happens as the Netgear, except possibly worse. And that adapter works fine on the laptop as well. I also just yesterday completely reformatted my computer hoping it would work, but of course didn't. [code]
wireless stuck on acquiring network address, very good connection, dell latitude d410
View 5 Replies View RelatedI have E4200 with fixed ip 192.168.1.2, DHCP off connected through LAN ports to FIOS ActionTec as 192.168.1.1. When connecting through wireless network off the E4200, I can obtain and connect fine under Guest network and WEP security, but for any other security setting, WPA, WPA2, Mixed mode, etc. I get the message "Aquiring network address" forever, and I never get a connection.
View 1 Replies View RelatedThis is an older desktop, Been utilizing the net gear to get on the Internet for months and it was working fine,shows it is connected to ssid but ip shows up as 0.0.0.0 I have other home computers hooked up and work g so I located there ip address, can I input it myself ? If so how?
View 2 Replies View RelatedI use windows 7.Ever since a couple of days ago, I have not been able to connec tot the internet.It says "not connected" and it says "limited access" next to my router, with 3 bars.Ipv4 Connectivity: Not connectedIpv6 Connectivity: Not connected
View 2 Replies View RelatedMy laptop does not recognize wireless OR the LAN anymore. IT says "Unidentified Network" My laptop connects to the network but the network doesn't connect to the internet. Before I got it and added a password it worked fine! Except it said Limited Connectivity" Here are the system settings for my laptop (I don't think wifi works for my PC either):
Manufacturer: TOSHIBA
Model: Satellite A215
Windows Vista
Rating 3.0
Processor: AMD Turion (tm) 64 x2 Mobile Technology TL-52 1,60 GHz
Memory: 894 MB
System Type: 32-bit Operating System
[code]...
I'm having a really annoying problem which is making my laptop almost unusable and a hassle to use. After a while of my laptop being on, my wireless network adapter will suddenly get "limited connectivity", and won't connect to the internet.Disabling and enabling the adapter will cause my computer to freeze, requiring a restart. The same with troubleshooting. The only thing which fixes this is a fresh reboot, however it always occurs again within the hour.Sometimes the entire adapter will randomly just disable itself, and the computer will completely freeze, meaning I have to press the power on/off. Sometimes the adapter will just disappear from Device Manager. Searching for "plug and play" devices will cause it to freeze.
Apart from having to reboot, what also seems to work is disabling the wifi from PC Settings, putting the computer to sleep, then awaking it and turning wifi back on. I've had to do that 6 times whilst typing this post.I've tried flushing my dns, registering it, renewing and releasing. Assigning a static DNS address. All those things. Though I may have done them wrong.Operating system: Originally came with Windows 7 64bit installed, issue began on this.I installed Windows 8 64bit Pro a month ago, did not reset settings. Problem persists[CODE]
I'm having a really annoying problem which is making my laptop almost unusable and a hassle to use. After a while of my laptop being on, my wireless network adapter will suddenly get "limited connectivity", and won't connect to the internet.
Disabling and enabling the adapter will cause my computer to freeze, requiring a restart. The same with troubleshooting. The only thing which fixes this is a fresh reboot, however it always occurs again within the hour.
Sometimes the entire adapter will randomly just disable itself, and the computer will completely freeze, meaning I have to press the power on/off. Sometimes the adapter will just disappear from Device Manager. Searching for "plug and play" devices will cause it to freeze.
Apart from having to reboot, what also seems to work is disabling the wifi from PC Settings, putting the computer to sleep, then awaking it and turning wifi back on. I've had to do that 6 times whilst typing this post. I've tried flushing my dns, registering it, renewing and releasing. Assigning a static DNS address. All those things. Though I may have done them wrong.
[B]Specs:[/B]
[B]Laptop model: [/B]Samsung RV511 (i5) notebook from around 2010
4GB RAM, Intel(R)Core(TM) i5 CPU M 480@ 2.67GHz
[Code]....
It's the latest driver according to Windows. I keep uninstalling the driver and installing random ones from 2006, 2011 etc however the same problem persists. I've tried uninstalling the driver and just rebooting, but problem still comes back after a while.
I have been having this problem with limited access with my internet. I have deleted mcafee, norton, photoshop, applications etc. I have restored the system to a previous date. I have disabled firewalls and antiviruses. I have an Acer Aspire with Broadcom 802.11n Network Adapter. I only have wireless as I am sharing my internet and therefore can't test it with an Ethernet cable. I cannot switch on and off the modem box either. I have this limited access which disappears by itself after a few minutes. Then it comes back again. I disable the wireless and enable it again which solves the problem for only a few minutes. I have checked my ip which is 192.168.1.20 with submask of 255 something - which I don't think is the problem.At last, I have switched to Safe mode with Networking but even in this mode I still have limited access. The internet connection keeps cutting off and on all the time.
View 2 Replies View Related