My network adapter is not seeing MY linksys wireless router. It sees the neighbors but not mine. Other laptops in the house can connect.It just started after a reboot. Tried buying a new adapter but that did not work either.
View 7 Repliescan this unit be used simply as a network adapter to connect to a wireless signal? Or does it have to have a cable modem?.
View 1 Replies View RelatedWill a realtek wireless network adapter connect to a Linksys WRT 110 router from a wood frame house to a concrete building approx. 100 ft. away
View 1 Replies View RelatedHow do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 Replies View RelatedOne day I got a blue screen saying there was a hardware or driver failure with the network adapter on the motherboard. I couldn't resolve the problem so I went out and got a new network adaptor. Pluged it in, windows found drivers for it. But I was getting a Unidentified network problem.I have a Linksys E1000 router, internet works on my laptop and xbox360 fine wired and wireless. So I changed ports on the router, changed cables, even changed routers. Still the PC wasn't seeing the router. So I download the latest drivers for the Realtek network adapter, install them, still nothing. So I thought maybe the router is to blame, downloaded the latest firmware and flashed it onto the router, reset it. Still the same. At this point I was sure the new network card was faulty. So I took the computer to the shop where i bought the card. He disabled the old network adapter in the bios. And he had the Internet up and running in the shop. I was happy and took it home... Still the same problem! Rang ISP done a lot of disabling, enabling, static IP no fix... except he told me to bypass the router and try plugging the PC directly to the modem, and that connects fine. I can get internet from the modem, but not through the router, yet everything else works fine though the router. As I said cables and ports in the router have all been changed and checked. When I do the network diagnostics in windows 7 is says, does not have a valid IP configuration.
View 19 Replies View RelatedWell one day i went onto my gaming PC and started playing, it randomly restarted and did some random windows check while starting. Then when i finally logged on i had no internet connection, my computer didnt sense there being a cable plugged in (Wired connection. The orange light wasn't on) So i figured i should just reinstall windows anyway (Blue screens, ect) After i reinstall i have the same issues. I have moved it to a different room and still the same thing. If i can't fix it then i plan to just buy a USB wireless but i would like to see what others think what i should do before i go making hasty decisions.
The computer say "Windows could not find a driver for your network adapter" I have tried many things i have found on this forum and nothing. So maybe a link to a driver? my Router is a Linksys WRT54GL and has always worked.
use a linksys wireless-g range usb network adapter to connect with a computer?
View 2 Replies View Relatedi need software for linksys 2.4ghz model no. WUSB11 version.2.6. i lost the disk in move now i have oec pc running off router but in bedroom i use linksys wireless adapoter need software
View 1 Replies View RelatedI recently purchased the Linksys E3000 router. My old network set up had been 100% wired, but with the new router we have converted to wireless on some of the internet capable devices. I have 2 pc's side by side in separate room from the router that we purchased wireless adapters for, the Linksys AE1000. One pc set up fine and accesses the internet with no issues. The second pc cannot connect the network. It sees the network with a good signal strength, but it times out when trying to connect.I called tech support and have been through a variety of things with them to no avail so far.Both of these pc's are running Windows XP SP3. On the one that won't connect, have already confirmed in device manager that the adapter is correctly installed. I uninstalled it, rebooted, reinstalled it anyway with no luck. With tech support already tried disabling the 5ghz band and changing the channel on the 2.4ghz band to 11.I have confirmed several times I am entering the password in correctly, and I did pay attention to case sensitivity.When I run ipconfig/all, it says under Media State: Media Disconnected.
View 5 Replies View RelatedI have 802.11n wireless network at home. Unfortunately my TV box requires internet to work and it doesn't have wifi card installed (only ethernet port). It's very unconfortable to connect tv box with the router through cable.
So is it possible to use WAG120N as a wireless client for my existing wifi network and connect tv box through cable with WAG120N? In that case WAG120N would be some kind of wireless network adapter for my TV box.
I have been trying to speed up my intranet and internet. Have 2 Broadband connections (1 ADSL 2 & BT Infinity - Fibre).
Adsl 2 (up to 10 meg) running D-Link 2680 - 68 mbs wireless 100mbs ethernet best I can achive.BT 2 Infinity (20 - 40 meg) running BT Wireless 2 router - 54 mbs wireless and 100mbs ethernet best I can achieve.Have a TP- Link SG1005D 1000mbs switch.
2 Destop PCs Windows 7 10/100/1000 ethernet card and 10/100 card.
Laptop 10/100 card and Linksys WPC300N wireless 300mbs adapter.
Also WD 1TB (500 mirrored) network storage.
Tried to bridge connections etc but not much luck.
I have purchased a couple network usb adapters (Netgear N-300 and Linksys AE2500) and both work fine surfing the internet but when I try to play World of Warcraft the wifi loses connection to the router and I lose all internet capabilities on my computer. My friends computer is still able to use the internet though.
View 1 Replies View Relatedbest wireless internet network adapter was? I have a Cisco/Linksys e3000 Wireless simultaneous Dual band router, so 2.4 GHz and 5 GHz are up for debate. My MoBo is the ASUS P8Z68-V PRO/GEN3, so it has built in bluetooth, which tends to affect my internet speed when used on the 2.4GHz bandwidth
View 1 Replies View RelatedI am trying to connect to the internet a second, older tower using the WUSB600N ver 2 adapter, the unfortunate part is that I have lost my CD's that originally came with the adapter. I am on my primary machine right now so I am able to get online. I am wondering if there is a way that I can get the proper drivers or software, put them on a USB drive and then put them on the computer that I am trying to connect?I have already tried this, but I cannot seem to get the steps right or I don't necessarily know what I am doing. I am at the Linksys support Page [URL] and I have tried to do as I mentioned before, but I am sort of just expecting it to GO and its not working. The computer i would like to make the WUSB600N adapter for is running windows XP pro Service Pack 3?
View 1 Replies View RelatedI need to connect a pc desktop and A linksys PAP-2T voip adapter to an existing wireless network(home network).
View 7 Replies View RelatedI just purchased 2 AE3000 adapters to update my wireless network and cannot get either of them to connect to my wireless network through either of two computers I tried. It hangs for a while looking for address and then I get the 'limited or no connection' note. But yet when I plug in my old AE1000 adapter into either computer I get connected right away. I've looked under the device manager and it shows up there, the LED lights come on and I see my wireless network show up on available networks. I am using the windows wireless manager in lieu of the Linksys one and as such I don't think any specific drivers are being used. I bought two updated adapters to start with is to keep current and NOT have problems.
XP Pro SP3
WRT350N Router
I recently purchased a Linksys AE3000 Dual-Band Wireless-N USB Adapter as an upgrade to my Dell Desktop Computer and to compliment the Linksys EA4500 Router that I recently installed. Generally it seems to work well and the 2.4 GHz network status typically shows speed to be 450 Mbps. However, I’ve discovered if the computer goes to sleep based on my power plan, when it comes out of sleep the “Available Networks” will show the network I’m connected to (2.4 GHz network) and a false network identified as “Other Network” with a Red “X” where signal strength would normally be. When I mouse over it; it shows Network Name: Other Network; Signal Strength: Excellent; Security Type: Unsecured; Radio Type: Unknown; and SSID: Other Network.
Initially I thought this was an anomaly caused by having both bands of the Router (2.4 and 5.0 GHz) set to the same SSID, so I changed the 5.0 GHz band to a different SSID and set my Media Players to access the new SSID. However, now when the computer comes out of sleep mode, Available Networks will initially only show the Router’s 2.4 GHz SSID and the phantom “Other Network”. It takes a while before the Router’s 5.0 GHz SSID shows up. We live in the country, so there are no other networks close to us, just my home network. It never shows the “Other Network” when I start or restart the computer and if I disable the adapter and then enable it, the phantom network goes away until the computer goes into and out of sleep mode again. Also, I uninstalled and then reinstalled the Driver and then reinstalled the Adapter using the Cisco Connect Software and the problem still exists. Finally, I disabled the Router’s 5.0 GHz network and the phantom network no longer appears under any conditions. The Dell (Atheros Communications) Wireless Card in the computer doesn’t have this issue under any scenario. On both the AE3000 and Atheros Adapters the 2.4 GHz network shows a signal strength of Excellent (5 out of 5 bars) and the 5 GHz network shows Good (3 out of 5 bars).
How to correct this issue? With the issues I’m having with the EA4500 and the AE3000; they are both probably going back to Amazon.
Sometimes I cannot connect to the router after my computer has been to sleep. This has occurred on different routers. I can still see the network, but am told I cannot connect when attempting to connect to it. Restarting/shut down does not solve the problem - I have to restart the router itself, and then my computer will reconnect automatically. Other computers/devices will be unaffected by this and maintain a connection the entire time. Atheros AR5B91 Wireless Network Adapter using Windows 7 Service Pack 1.
View 2 Replies View RelatedI am only getting G connections with xbox 360 wireless n adapter. I should be connecting with N.Internet is BT Infinity. Original BT HomeHub3 does not have n problem and I can connect fine at n speed!If I set e2000 to N only the adapter can not connect at all.I currently have to bridge to my laptop using N wireless card to get good connection speed.
View 5 Replies View RelatedLinksys has disabled my wireless adaptor for wireless devices such as my Netflix streaming movie player. They are asking for my routers user name and password which I am not accessing right, I get "401 Authorization required" How do I factory restore my router? It's a D-Link DES-1105 router model BEFW1154V4. I need to enable my network for wireless connection. How to get my routers user name and password? I 've had my Netflix player hooked up and working for almost a year and have never encountered this problem. Im going to purchase a linksys wireless adaptor the first of the month with having a secure connection to linksys instead of having to wait all day for wireless linksys with the Ativa adaptor I already have?
View 2 Replies View RelatedI lost my power adapter for the WRT54G router. I have a 12V / 1000 mA brick adapter.
View 5 Replies View RelatedI had to change from a WRT300N wireless router which died to a new E2500. I noticed that the speed my computers report that they are connected to the wireless network connection is now 144.5 mps, versus 270 mps with the WRT300N. There is no change in location of the devices or computers. The computers use a WUSB300N adapter. Is there a setting or setup that needs to be changed?
View 2 Replies View RelatedSo I recently updated my desktop to windows 7 and I have lost the CD for my E3000 router. My desktop doesn't have a wireless adapter I always had it set up on a direct connection. So I went to the E3000 support and downloaded the software on my laptop and burned it to a DVD and put it in my desktop so I could update the drivers manually and be able to connect to the internet. But it seems the software only supported wireless connections, am I just sol? Is there some way to get my desktop to update the drivers for the router?
View 2 Replies View RelatedCurrently my setup works fine except that I need another ethernet port.I have a E4200V2 with a HP laserjet 4000N printer connected via JetDirect ethernet and I am able to print with any of my devices.However, because I have need of another ethernet port, I am wondering if anybody has tried using a parallel to usb cable? The parallel side of the cable being connect to the printer and the usb side to the router.
Or if I really want that port made available, will I have to get some type of external print server?
I know that HP makes a JetDirect Card with a USB port, however, I don't want to spend the $80 on ebay to get a used one if a $10 new cable will work.
Trying to connect my Dell Dimension E310 to my Linksys WRT54GS with a TRENDnet wireless N USB adapter. It sees the router, it connects, I show strong signal strength, but get a "limited connection or no connection" error back from the router...can't get on the Internet. If I use an Ethernet wire and connect it to the router, it can set up a wireless connection with the machine, I can unhook the hardwire, and I'm good to go. But every time I reboot, it won't connect unless I set it up with the hardwire first. Impractical.All other devices attached to the router are fine and connected to the Internet. How can I get the router to maintain the settings for this new connection so it will connect wirelessly when I reboot?
View 1 Replies View RelatedOn the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find?
View 9 Replies View RelatedWRT610v2 running latest firmware.xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars.Connects to 2.4 network just fineWon't pull an ip address and reports "Not connected" when I select the 5.0 network.I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network.So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not..If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
View 13 Replies View RelatedWRT610v2 running latest firmware.
xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars. Connects to 2.4 network just fine, Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network. So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not. If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
I have 2 laptops with wireless N adapters that will connect at a maximum of only 72Mbps. I've tried changing the security mode to WPA2 Personal, channel width to 40 MHz only, and 20MHz only. I've changed the network mode to N only. I've updated the drivers on the adapters and ran the update on the E2500 router. I get the same 72Mbps if the laptops are right next to the router. How can I get the connection speed faster?
View 1 Replies View RelatedYesterday I bought a linksys AE2500 usb network adapter. So I set it up on the computer downstairs from the router, roughly 30 ft distance. There is a desktop running a linksys pci card directly next to it. So I fire the computer up it see's the network but it won't connect to it. Then I take the computer up to the room the router is in and it connects. The range on the adapter says 300 ft and I do realize that there are walls and other obstructions that cause that number to fall but I find it hard to believe that the adapter is out of range but I can't think of anything else to explain it.
View 7 Replies View RelatedWhat is the best method (the one that works) to connect the E3000 with the SPA2102 phone adapter? Or, is it not possible?
View 9 Replies View RelatedI need to reset my wireless adapter frequently Realtek RTL8188CE wireless Lan 802.11n PCI-E NIC after coming out of sleep. I am using WRT-120 router.
View 2 Replies View Relatedcan the linksys ae1000 adapter be use to hook a printer to the network?
View 1 Replies View Related