I have 2 separate networks. One is a DSL circuit, the other is a T1. How do I enable the two networks to logon to the same domain, but use each of their own gateways for internet access?
View 5 Replies
I have a gmail site,For some reason, I am unable to log into the site.
View 2 Replies View RelatedI am not an expert at routing but was wondering what the most cost and time effective way to have an ip request return with another ip address from outside the WAN of the router. Specifically want to have an application request for example 192.168.1.121 and have 173.194.43.41 respond and communicate with the application instead. To make it a bit more interesting I'd like actually to set a table or config file to point to a domain name (url) which gets resolved as an ip address. (Port independent) To get a better understanding: one example might be typing in 192.168.1.121 in a browser and googles search engine comes up on the browser.
another example might be typing in 192.168.1.121 in an ftp client and it hooks to an ftp server on the other side of the world which resolves to ftp.this-is-a-test.com.Make sense? I was looking at openwrt and tomato a little but I don't think I have such a complete grasp on how to do it in general. Being that it seems they are 2 different layers of the network model, I was told it can't be done but I don't know if I can believe that yet. Either by third party software orreprogramming the router or adding another device to the network, I have a feeling that it seems like such a simple redirection that it can be done somehow
I removed my computer from a domain to a workgroup,I then rebooted the pc and now it si asking me for a username and password.I can not access important information on the local drive.
View 1 Replies View RelatedWe just had a TEW-72GR router fail and replaced it with a TEW-GR. Now I am unable to get to my domain (mydomain.net) from outside the network. Inside the network, all appears to be fine. I can enter that address and get to the site with no issues.We use SBS 2008 with windows 7 clients.All clients can get out to the web, we can send and receive emails, but I can not access the domain.
View 2 Replies View RelatedMy dlink aircard wont connect to wpa psk networks.Why is that.
View 5 Replies View RelatedLogon failure: The user has not been granted the requested logon type at this computer" Im having this same problem on two computers. One running windows vista ultimate 64bit and windows 7 home premium 32 bit to windows server 2008 r2 64 bit?
View 3 Replies View RelatedI have a network domain with 2 domain controllers running windows server 2008. At some point the DNS name for one of the servers got messed up and they stopped talking to each other even though they are on fixed IPs. The DNS problem has been fixed, but they haven't started communicating again. While the DNS was messed up the domain controllers kept running a different copy of the network. The DFS stopped replicating, the users lists fragmented and the network separated into two "shadow domains" with the same name. DC1 says it is healthy, but it claims DC2 is offline. DC2 claims it is healthy but DC1 is offline. I don't even know where to begin repairing this rift.
View 1 Replies View RelatedMy home network starts from the ISP/Cable modem to a Belkin wireless router.
A WIN XP box connects via ethernet cable in that room. A second WIN XP box connects via wireless in the next room. A Third box Win7 laptop connects via wireless in another room.
All machines have Internet Web browsing working fine, all machines can see each others shared files and printers across the home network.
Here's where I get creative... I added a fourth box WIN XP via ethernet (LAN to LAN) to the Win7 Laptop. It shows as an �unidentified network� of type Public in Network and Sharing.
Using Shared Internet Connections on the Win7 laptop, the fourth WIN XP now also has Web browsing working just fine across the LAN to the laptop over the wireless and out to the world.
The Win7 Laptop can see shared files and printers on either side of its networks (fourth WIN XP on the LAN side, and first and second WIN XP on the wireless side), and they can see its shared files and printers.
However, the fourth WIN XP on the LAN network won't see the first and second WIN XP on the wireless side. File and printer sharing doesn't see to make the jump across the Laptop Win7 in the middle.
How do I bridge the two networks for file and printer sharing ??
why the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies View RelatedI have got a PC at work (Windows XP Pro SP3) that is on two networks with the IPs 10.20.30.167, subnet 255.255.255.0 (internet enabled) and 10.0.0.20, subnet 255.255.255.0 (no internet). On the 10.0.0.X network there is a gateway with the IP 10.0.0.200 allowing access to another network; 192.168.60.X, subnet 255.255.255.0 (no internet). I have added the route on my work PC to access the 192.168.60.X network via this gateway and I can access all PCs on all three networks from this PC.Now, I am using LogMeIn Hamachi so that I can access the networks at work from home. The PC at work is the 'gateway' PC on the Hamachi network. When installing Hamachi it created a new network connection and bridged this connection with my 10.20.30.167 network adapter to allow access to the 10.20.30.X network from an external PC when connected using the Hamachi VPN connection. I have manually configured my Hamachi connection on my PC at home to the IP 10.20.30.169, subnet 255.255.255.0, with the default gateway set to 10.20.30.167. I can ping all computers on the 10.20.30.X network from my PC at home.
I then added a route on my PC at home for 10.0.0.X to go via 10.20.30.167 (the 'gateway' on the Hamachi network). I also enabled IP forwarding on the 'gateway' PC (my PC at work). I can not ping any PC on the 10.0.0.X network from my PC at home apart from 10.0.0.20 (the other NIC in the Hamachi gateway PC) and 10.0.0.30 (another PC on the 10.20.30.X network that is also on the 10.0.0.X network).Now, with IP forwarding enabled on the Hamachi gateway PC I would assume after adding the route on my PC at home for 10.0.0.X traffic to go via 10.20.30.167 that I would be able to ping all PCs on the 10.0.0.X network...I also tried adding a route on my home PC to send all traffic for the 192.168.60.X network via 10.20.30.167 which has a route via 10.0.0.200 to the 192.168.60.X network, but this also did not work.I then tried adding the 10.0.0.20 network adapter into the network bridge that the Hamachi connection made, also keeping both IPs (10.20.30.167 and 10.0.0.20) on this network bridge by adding them into the 'IP Settings' in the 'Advanced TCI/IP Settings'. I also added the 10.0.0.200 gateway for good measure. I still cannot ping any PC on the 10.0.0.X or 192.168.60.X networks from my PC at home.
I have also added the route to the 10.20.30.X network on a PC on the 10.0.0.X network to go via 10.0.0.20 and tried pinging a PC on the 10.20.30.X network but this also has not worked. Also setting the default gateway on a PC on the 10.0.0.X network to 10.0.0.20 does not allow this...Surely bridging the networks 10.20.30.167 and 10.0.0.20 on my work PC would allow another PC on the 10.0.0.X network to access the 10.20.30.X network after adding the route or setting 10.0.0.20 as the default gateway?
I have two computers. Computer A is connected to the internet through GSM network. Computer A also have NIC adapter which is connected to local network with IP 192.168.33.10/24.
Computer B in connected to internet with DSL connection.
On both machines I use TeamViewer to make VPN secure tunnel between this two computers. Computer A gets IP:7.200.100.2 Computer B gets IP:7.200.100.3
How can I access from computer B to specific device with IP 192.168.33.250 which is on local network of computer A?
Is it possible to route traffic from VPN to other local network, or it is some possibility to use port forwarding from VPN connection to specific IP address on the local network to specific port number?
We have a PPPoE DSL link with a dedicated IP providing by a small ISP(ISP A) in Canada. We are having trouble reaching a small group of IPs in the US to be able to access some client resources.We have eliminated all possible local issues by removing the firewall and making a direct connection to the ISP. We have also had numerous tests prove successful when we use other local ISPs.
Trace routes show that the packets get dropped a few hops from the destination on a US ISP(ISP B).The routes even appear to be very similar to the other ISPs we tested. We escalated to ISP A and they say that everything is working properly on their end and the problem is with ISP B. They claim they "have no partnership with ISP B and therefore cannot create a ticket to get it resolved". I tried calling ISP B but I get nowhere because I am not a customer of theirs.
My solution is to give ISP A the boot, but management has denied that request because of the amount of effort required to switch over. How I can escalate this? Is there anyway to go over and above the ISPs?
I have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
Have a 3750X running at the moment and has about 30 vlans all connected and just use the ip route global config command to enable routing. Plan is to switch out to the 4503E, with IPBase license. When ever I issue the same command, and do a show run its not there. I get no error when I issue the command either. And yes I have rebooted. Do I need to use RIP or OSPF routing? When I do a show ip route the screen looks the same with all the codes, though gateway of last resort isn't set even though I do have ip route 0.0.0.0 0.0.0.0 a.b.c.d in the config. Or is ip routing just enabled by default?
View 6 Replies View RelatedI have two switches 6509 one switch is confire with VTP domain ABC Other switch is configure with ABZ, At present the switch is configure with the L3 interface and one fiber cable is connected between two switches.I want to remove L3 configuration wants to make L2 etherchannel and wants to ceraeate Loop back will assing same ip both side.The OSPF is configure both side , i will not do any changes in the OSPF as L3 ip is advertise in OSPF.
View 1 Replies View RelatedI have an skill exercise with 4 Routing Protocols Default Route,Static Route,Eigrp, Ospf. I have about 6-7 routers, and each of them has an routing protocol. But the problem is the Main router INTERNET, which it has to use Static in a direction, and default in the opposite path. This is the scheme of routers and how the r.protocol have to be configured.
View 19 Replies View RelatedThe websites I usually go on now have some type of error page when I go to them. So far it has happened to 2 of them though they might not be related.
Here's what the page says:
Site 1- Valenth
Quote:
Warning: mysql_connect() [ function.mysql-connect]: [2002] Connection timed out (trying to connect via tcp://ec2-184-73-84-14.compute-1.amazonaws.com:3306) in /var/www/valenth.com/include/database.class.php on line 25
[Code]....
i've had this internet problem that has been going on with a wireless laptop i've had since april. it only happens on this computer, and i've tried many solutions. occasionally, i will try and go to pages on google chrome and an error pops up that says "this webpage is not available." when i play games that are online, they get disconnected as well. i've added google chrome and my other browsers to the firewall list and i've also changed the DNS server. when i use the troubleshooter it says something like "router, or modem is not connected to the internet. i've even downloaded the "fix it" program and it detected no problems
View 1 Replies View RelatedI can't get RDP to work on a specific computer.I've already set it up on the router, know the IP address, and I can get it to work great with the server, but the workstation we want it to go to won't accept it.I checked, it's set to allow RDP, the firewall exception was setup, also turned off the firewall completely, removed the antivirus software, checked TCP/IP filtering on the lan connection, even changed the listening port and still nothing.
View 9 Replies View RelatedProblem with a conflicting IP address. Basically on a normal running day my wireless is switched on and connected perfect to my internet, however if i want to download any large files i plug my Ethernet to my laptop and disable the wireless from my laptop, instantly then the LAN connection kicks in and im on the internet again as i find download speeds are faster through a LAN. However today my wireless is fine but the second i switch to LAN the ! symbol appears and a message says their is an IP conflict.
View 2 Replies View RelatedI've been timing out via any FTP client, including FileZilla, FireFTP, and a few others. I even downloaded a few just to see if I could connect with other clients.I contacted my host who can't recreate the issue on their end. I contacted my ISP who instructed me to use my command prompt in order to connect to their server, and that of mozilla. Both times I was able to connect via the command prompt.I don't understand what's going on.If I can connect to the sample sites that my ISP gave me, why can't I connect using an FTP client any longer. What possible change could have been made to have caused that disconnection that happened a few nights ago, and is now causing the timeouts I continue to receive?
View 6 Replies View RelatedHow can i actually change my ip...tryed those cmd things but nothing works. Ineed to change ip somehow.
View 1 Replies View RelatedI'm running a VB Script from the logon script to add printers when users log on.The Colour printer is added no problem but the black and white printer was working but now wont.The print share names are correct and the server name is correct.
View 2 Replies View Relatedsbs 2003 never had updates installed till now and required reboot. it took 3 hrs to startup and now i just logon and it is still applying computer settings. i booted to safemode and changed DNS and still slow logon - going on 45min.
View 1 Replies View RelatedI have been trying to enable L3 intervlan routing on C2960S Switch with ip routing command and that was the output from the Switch: [code]
View 6 Replies View RelatedIn the following scenario, how will the 2950/2960/2960S series behave:
- VTP server/domain configured on a 6509
- A access switch (2960) currently configured in transparent mode with all VLAN it requires
Will the switch drop any traffick if we change it from transparent to client mode if the VTP server has the exact same vlans defined as the access switch had when it was in transparent mode?
I can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.
View 3 Replies View RelatedI am trying to join a Cisco Catalyst 3560X-24T-L to an existing VTP domain, my question is what configurations should I do to this switch?I have already gave it a hostname, setup passwords, enabled telnet, created a management address on port g0/24.I would like it to be on VLAN 13, is this done from my server switch, or done on the new switch?
View 10 Replies View RelatedI am trying to set up the SG300-52 and am struggling, I have a domain controller with IP address 192.168.0.1 I have a broadband router that is has a dynamc ip address. I have set up vlan1 aand vlan2
Vlan1 is getting its ip address from the domain which is 192.168.0.110
vlan2 is getting its ip from the broadband router.
I have setup Domain Name System in the Ip configuration tab
on Vlan1 I have a connected a dumb switch this connects all the computers in the local network. What I cannot get to work is the internet vlan.
who has setup up vlan routing with domain controller
We know that every node in the network uses its routing table to forward the packets towards their destination. I have a doubt that which data structure used to implement these routing protocols.
View 6 Replies View Related
