SRW2024 Grace Hotspot On VM Inside Network
Jul 3, 2013
I have been playing around with some hotspot/captive portal software on my home network. At the moment I have Grase Hotspot setup on an old computer in the garage with a Engenius outdoor wireless AP connected to it.I would like to have Grase Hotspot loaded onto my Proxmox server inside the house and only use the wireless AP located in the garage to allow connections.My network is as follows.
Internet--->PFSense Router---->Linksys SRW2024 Switch--->Proxmox-->Out to garage into another switch---> Engenius AP
I tried it on a VM, but Grase Hotspot tries to hand out IP's to the entire network, instead of just taking connections from the AP.
View 1 Replies
ADVERTISEMENT
Dec 18, 2010
I have 2 questions.Om my cisco 2811 (IOS 12.4(15) T9 IPBASE W/O Crypto) i am using 3 interfaces.And i have a pool of Global addresses: 200.x.z.97-200.x.z.126 255.255.255.0
FastEthernet 0/1 description WAN interfaceip nat outsideip address 200.x.y.253 255.255.255.0
GigabitInterface 0/2/0description DMZ interfaceip nat insideip address 10.0.0.1 255.255.255.0
GigabitInterface 0/3/0description LAN interfaceip nat insideip address 192.168.0.251 255.255.255.0
[Code]....
View 8 Replies
View Related
Oct 24, 2011
we have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies
View Related
Mar 6, 2011
I want to set up a wireless network with hotspot for billing.I have a Cisco wireless n router.My System info is below:
OS Version: Microsoft Windows 7 Ultimate , 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU E4600 @ 2.40GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 2013 Mb
Graphics Card: Radeon X300/X550/X1050 Series Secondary (Microsoft Corporation - WDDM) , 3 Mb
Hard Drives: C: Total - 119899 MB, Free - 26762 MB; D: Total - 118415 MB, Free - 102992 MB; G: Total - 305242 MB, Free - 19123 MB;
Motherboard: Dell Inc., 0GM819, , ..CN1374086607G4.
Antivirus: avast! Antivirus, Updated and Enabled
View 2 Replies
View Related
Apr 7, 2013
I am new to forum and stuck in connecting one computer to laptop. Here is the scenario: One computer running on windows 7 is connected to wireless router Netgear WGT624 v3 via Ethernet cable. The second is laptop running on Apple. The first one computer does not have any wireless dongle. The laptop is connected with Wifi Hotspot of mobile phone. Now I want to make network between computer and laptop via wireless router to share files and the Wifi Hotspot which is already used by laptop.
View 3 Replies
View Related
Oct 23, 2012
I have a local network that I want to connect to a WiFi site. The site is a free service offered to our community by a local ISP. The network uses a wireless router but cable links the two relatively old PCs. They are used for a single inventory-accounting program. One serves as the softwre host. The organization wants episodic Internet access so they can use a software update auto installation service. There are alternative ways to accomplish these updates, but this pathway is the only one acceptable to the organization. Why they reject a simple thumb drive using an out of system download is beyond me, but it seems to be a locked in idea. Oh, the current wireless router cannot accept DD-WRT, but one is available if it can be used if useable.
View 3 Replies
View Related
Oct 30, 2012
I am working with a friend who has a home office that is not in a location where DSL or Cable is available. His only option for internet is using a hotspot - in this case, the Elevate Hot Spot from AT&T.
He needs to network two computers so that he can enable QuickBooks Pro in multi user mode - i.e., data file shared on Computer A, accessed by Computer B.
I thought at first that perhaps I could just setup a wireless connection for the office network - however, whenever that connection is on, then obviously neither computer can access the hotspot.
Trying to keep this at *minimal* cost.
My best idea is to old school network - i.e., connect the two computers via crossover ethernet. Am I correct that this will work? Seems to me that then both computers *should* still be able to access the hotspot via their wifi, yet also be networked for file sharing.
My questions are:
1.) Is this a correct assessment?
2.) Are there any road blocks I should be thinking about?
3.) Any reason not to do a direct connection (i.e., any reason I should entertain connecting to a switch instead?)
4.) Is there a certain order I should do things?
View 2 Replies
View Related
Jan 28, 2013
I did not know to update the boot software of my SRW2024 first, then update to 1.2.2b.I need to go back to the 1.0.0.86 firmware.
Is it downloadable and will it work (ie work backwards and then do it properly)? I know how to use hyperterminal and the xmodem protocol if need be.
View 9 Replies
View Related
Oct 6, 2011
I am unable to connect to webview on our SRW2024 switch. I use a macpro G5 running 10.6.8. When i try to connect to it through Safari, Chrome, or Firefox using 192.168.1.254, I receive a message that a connection cannot be established. 192.168.1.254 is the ip mentioned in the manual. I used an ip scanner and it showed the actual ip is 192.168.0.1. But I cannot connect to webview through this ip either. We got this switch a year ago and did not change any settings, we just connected it and it worked fine. But now we want to change some settings on the switch but cannot connect.
View 1 Replies
View Related
Sep 21, 2010
I have the same problem with my two WAP4410N connected to my Cisco SRW2024 Gigabit switch.It appears that there would be a time where the PHY's between the WAP and the switch are hung.The lights on the Gigabit switch are constantly flashing.
It is until I disconnect and reconnect the network cable between the WAP and the Gigabit switch that the problem is momentarily solved. Then it seems like another high traffic usage of the WAP will cause the connection to hang. This solutions is totally unacceptable as I am not willing to open my wiring closet every time to fix this hang. Also I've lost precious data between my client and server because of this hang!
I don't think the problem is with the Gigabit switch as I have other Gigabit devices connected to it and I never get them to hang like the WAP.
I saw on the release notes (although the firmware has not been posted) that there is a problem with the WAP Gigabit PHY. From the release notes, it seems the firmware will have an option to take down the speed of the WAP Gigabit PHY from 1000BT to 100TX. This would be a shame if this is the final solution as one main reason for purchasing the WAP4410N is its Gigabit capability.
Being a networking PHY designer who had also worked on other Cisco products, I'm surprise that this problem had not been resolved in their qualification and interoperability lab.
View 1 Replies
View Related
May 10, 2011
Have an SRW2024 that I was updating firmware and it got interrupted. Now I can't access the switch from either console or IP. Switch will not pass traffic. Is there a way to get this switch completely reset so I reconfigure and use it again?
View 1 Replies
View Related
Mar 26, 2013
I HAD similair problem:[URL](Have ver 1.1) Forgot password. Restored to v1.0.0.86 via telnet Been playing around with telnet AND web based updates Read somewhere else (Web-based ONLY works with IE) (Tried Web-based and keep getting "Copy Failed/Undefined Error" and 0 Bytes transfered) Know to upgrade "Boot" first, then "Software Image" THEN reboot
Tried telnet (not through web-based startup) Can get to "lcli" (by Ctrl+Z twice)Retyped Username and Password:
At "console#" tried typing "copy tftp:///srw2024_16_boot-101.rfb boot" didn't work : "Must be valid URL or reserved keyword"
Where am I going wrong?
View 1 Replies
View Related
Jan 24, 2011
Every "once in a while" (about a week with my network load), the SG300 crawls to an almost standstill of all IPv4 activity (haven't got IPv6 enabled here yet, so I can't comment wether this applies to IPv6 as well). It seems pure L2 transmissions is not affected, but L3 definitely is (down to 20mbit as opposed to the 600+ rate I usually get).
Soft-rebooting the switch (via the webgui) useful, and the intervals of the crashes seem related to total bytes transmitted, not time. I have jumbo frames enabled, and disabled flow control on on the switch and all hosts.
Firmware Version is 1.0.0.27, md5 1987292110f5657e74308dde30c03dc4 Boot Version is 1.0.0.4 md5 4c9a0b6a9f1346736646d08ab94ae2ac
View 13 Replies
View Related
Apr 26, 2011
What kind of cable is required to connect to the Console on a Linksys SRW2024 switch ? ( I've lost the original cable )I use the following settings: Speed 38400, 8 bits, no parity, no flow control and stop bits 1I have tried a serial cable, no go.I have tried a null modem cable with partial handshaking, no go.I have tried a null modem cable with full handshaking, no go.For the null modem cables, if I use it to connect between computers using hyperterminal it works very well. What I type on one computer appears on the other computer's screen.However, I can't get anything out of the switch. I've tried pressing Enter repeatedly, resetting the switch with the Console cable on, etc.
View 2 Replies
View Related
Mar 14, 2013
I need a switch to configure a static ARP entry for a MS NLB multicast.
Could answer me if I can do with the SRW2024-K9-BR?
View 4 Replies
View Related
Nov 25, 2011
I'm trying to configure hairpinning on my Cisco 887VA VDSL router, so all LAN users can connect to the server using SMTP port 25 which is also in the same LAN subnet, using external router address, which is assigned to dialer1 interface.Traffic comming in from outside works fine.
External IP: 1.1.1.1/29
PC address connecting to the server: 192.168.101.28
Server address: 192.168.101.200
IOS: 15.1.4M1
[code]....
I'm running tcpdump on the server on port 25 and... nothing happens. The traffic is not going through.One thing that I've notices in debug ip packet is this line:
s=1.1.1.1 (Vlan1), d=192.168.101.200 (Vlan1), len 52, rcvd local pkt
shouldn't source be internal vlan1 IP - 192.168.101.1?
View 3 Replies
View Related
Aug 3, 2011
Setup as follows:
Cisco ASA 5510
Inside 172.17.101.249
outside 5.5.5.2
DMZ 192.168.100.1
I have an internal server 172.16.1.202 that is PAT to 5.5.5.103 to allow RDP connections. - This works fine from the internet.I have now been asked to allow our guest wireless (192.168.100.0/24 - DMZ) to access this same external connection.We have 2 cisco controllers, with the guest controller "anchored" in the DMZ.I cannot get this to work.Both the DMZ and inside NAT their internet connections to 5.5.5.2.
View 4 Replies
View Related
Feb 8, 2013
I want to transfer big fiiles from PC to another PC, and it has happened frequently, I was wondering is there any way that I can send them directly with high speed if they are connected to the same router (my Router),I got an Desktop with Windows 8 64bit.The target PC (to transfer files) Laptop Windows 7
View 2 Replies
View Related
Jul 1, 2012
I have a simple isp topology built in GNS3, for testing (pppoe) dialers:cisco router(R1) connected to my pc network card, doing NAT translations for all the devices in the topology.I know how to configure NAT for spesific ip range, but i can't find out how to configure NAT for networks which are learned through ospf (or any other dynamic way).
View 2 Replies
View Related
Jul 29, 2011
I have a 5505 with the security plus license. I have a web server in the DMZ that needs to talk with a server on the inside network but it doesn't seem to be able to. Im guessing there is something I need to do to enable the DMZ to talk to the inside network.
Here is the config.
[code]...
View 1 Replies
View Related
Jun 25, 2012
I have setup a few Vpn clients but no ones able to access the inside network.The clients all get a Ip address from the pool and DNS servers Ip's. But cannot ping or connect to there pc's. I'm thining its somewhere in the ACL.
View 2 Replies
View Related
Nov 29, 2011
i have cisco asa 5505 Security adaptive firewall. my inside network is 192.168.1.0 255.255.255.0 . i want to add static route another network i have that network id is 192.168.2.0 . 255.255.255.0.how i can add the route.
View 9 Replies
View Related
Apr 16, 2012
I have an ASA 5510 which works great except I'm unable to connect to the remote access VPN from inside the network (behind the ASA). Is there a special NAT exemption required? [code]
View 6 Replies
View Related
Feb 26, 2012
I'm looking for a content filtering/antivirus/antispyware appliance for my company. Right now we have an ASA 5505 at the edge. We have several outside employees connecting via Cisco VPN clients to the ASA. I need an appliance that can do content filtering for my inside network, guest network, and VPN users. That's two local VLANs and a VPN pool which are all terminated at the ASA.
I've had good luck with Cymphonix in the past, but their boxes are a bit steep for the amount of throughput I need. We'll probably be moving from a 15/15 fiber connection to 80/10 cable soon since our provider can't seem to keep us online; even with an alleged "100%" SLA. They just don't have a network capable of anything close to 100% uptime, plain and simple.
I'd like to keep the ASA running as our firewall and VPN server, so the device needs to be able to do content filtering/av/as in a transparent mode.
View 9 Replies
View Related
Feb 10, 2011
I'm just new with ASA. I'm just self-studying on it. I was tasked to have an ACL that will allow inside hosts to access a specific network. Is there a way on how to know all the inside hosts on the behind ASA so that I can do a "object-group network" on those inside hosts which I think it will look neat.
View 1 Replies
View Related
Dec 11, 2012
I am working on pix 525, when connected through console I can access the whole internet but when i connect the pc to the inside interface i have no access to the internet. the pc can ping the pix inside interface and from pix i can ping the pc. My configuration is shown below.
PIX Version 7.2(2)
!
hostname pix
domain-name xyz.edu.pk
enable password xxxxxxxx encrypted
[code]....
View 8 Replies
View Related
Jan 27, 2013
I am trying to configure a server(192.168.5.50) in DMZ(192.168.5.0/24) to be able to communicate with a domain controller(10.5.44.220) in the inside network(10.5.44.0/24). I made some configuration using ASDM(not familiar with the CLI) but not working and it caused existing NAT not to work, for example RDP(TCP 3389) connection to 38.96.179.220
The things I am trying to achieve are
1. two way commucation between 192.168.5.50 in DMZ and 10.5.44.220 in Inside for SecureAuthPorts and SecureAuthOutbound service groups
2. NAT for 192.168.5.50 mapping 38.96.179.50 for the service groups mentioned above
3. NAT for other hosts already existing
View 2 Replies
View Related
May 19, 2011
I'm using a Cisco 1941 router with two WAN interfaces. One is directry connected to our ISP and one is connected to another router wich is then connected to another ISP. Hosts on the LAN cannot access the Internet at all but the router has Internet access, im guessing its something simple but i cant seem to spot the error, i have removed the ZBF configuration from the interfaces. [code]
View 3 Replies
View Related
Nov 8, 2011
i have asa 5505 , so i wanna my inside network to access to the internet. my internet gateway is 155.155.155.1
: Saved
:
ASA Version 8.2(1)
!
interface Vlan1
[Code]....
View 3 Replies
View Related
Jan 7, 2011
I am having a spot of bother with a Cisco PIX515, I have posted the current running config below, now I am no cisco expert by any means although I can do basic stuff with them, now I am having trouble with traffic sent from the outside to address: 10.75.32.25 it just doesn't appear to be going anywhere.
Now this firewall is deep inside a private network, with an upstream firewall that we don't manage. I have spoken to the people that look after that firewall and they say they they have traffic routing to 10.75.32.21 and 10.75.32.25 and thats it (although there is a website that runs from the server 172.16.102.5 which (if my understanding is correct) gets traffic via 10.75.32.23. [code]
View 2 Replies
View Related
Jul 5, 2011
Got a problem accessing our webservers on the inside interface from other clients on the inside interface on our ASA 5505.As in, they type in url... in their browser, and it wont work.
However, if we use a PC on another outside network, it works just fine! [code]
View 2 Replies
View Related
Apr 17, 2011
I am setting up a new ASA 5510 on our inside network so that we can terminate our VPN connections on this ASA. I can get the VPN to work fine however I noticed that once I turned on my VPN profiles now when I try to access the ASDM I'm getting the VPN logon page. So I decided that in order to resolve this I need a separate interface dedicated to management of my ASA.
I'm trying to come up with the best way to do this. I've got two ports on the ASA plugged into my core switch. One is on a separate VLAN from the rest of my network traffic. This is the port I want to use for management. The second will be used to route all of my VPN traffic.
So far I haven't been able to get this to work at all. My thought was that it had to do with routes, NAT and ACLs. I've been playing with them but can't get any combination to work.
View 2 Replies
View Related
May 6, 2013
I have an issue accessing the inside network of my church from VPN. This only happens when I connect from my home network. I have no problem accessing inside network of my church if I'm connected from else where (my Clear Hotspot or someone else's house). Here is the hardware detail:
At the church, we are using Cisco ASA 5510 and we have so many VPN tunnels to different churches. At home, I 'm using Cisco ASA 5505. See that attached configuration for my home ASA5505.
View 1 Replies
View Related
