Setting up a netgear n600 (WNDR3700) in my home. I have tried connecting two PCs to the LAN and am only getting 100mb/s with most of my patch cables(all are cat5e). I was only able to achieve 1Gb/s with 1 of my cables(which is actually a few feet to short for my shortest run). Both PCs have gigabit capability. What are the chances that 5 out of 6 cat5e cables are bad? Am I missing something?
View 2 RepliesUTP cables are crossover cables or straight through??
View 5 Replies View RelatedRecently bought a NAS (Synology DS212j), upgraded to a gigabit router (Netgear WNDR3700), and now want to utilize the pre-wired ethernet ports in our condo. How to do this last part.
Do i just plug one of the LAN ports from the router into the wall using a Cat5e cable? Then the signal will be routed to all ethernet ports through the patch panel?
I located a patch panel in the closet, but not sure if its wired correctly or which connection goes where. I took some pics that you can see here: URL
you can see in one of the pictures that some of the cables are only connected at one side.
There are 2 locations to choose from. One location requires me to run longer CAT6 cables. 7 of them. The other location requires me to run a longer RG6 cable. (the CAT6 runs would then be about the shortest they could get)So, I guess I need to know which can handle running parallel with power cables better, 25feet of RG6 or CAT6?The parallel with power cable is only for about 6-8 feet, but that's already more than it should be for CAT6.
View 4 Replies View RelatedI am renovation my own house, and I have started to hard wire for the network/s, but I am also trying to incorporate so much more than any previous “wireless” setup I have had, well I am a bit confused to say the least.I would like to set up a home network and media server system which includes:Internet browsing (multiple rooms and wireless) File sharing, printer sharing, scanner etc Music/Video sharing/streaming, TV etc.I have started wiring (we are renovating) with Cat5e, and have just replaced the old POTS (telephone) wiring with Cat5e and taken the individual telephone wires (including the incoming telephone cable) back to one central connection unit in a network patch panel. This has improved the speed of my DSL download connection speed from 1.2mbs to 6.2mbs. unreal!, so that did get me a bit fired up!I am currently wiring data points (Cat5es from each room) back to the same panel, but to be honest I am not really sure where to go from there! Also, I have wired Sat cables back to this point ready to be connected to sat TV (dish) in case if we get it. This patch panel is in a small passageway that goes through to the garage from the house. It is conveniently located next to the mains board which I have just replaced. My original idea was to put any extra needed equipment in the same location, but looking at it, I think that I may have to think again, for there is little room. I have found a small alcove in the upstairs games room which has a shelf, and which could take any hardware, also it will be dust free (unlike the place leading to the garage). I can run as many cables as needed from this location to the patch panel, but obviously I would like to know how many, as I am not familiar with networking on this scale, my only other experience being wireless setups. For example, would the switch need to be located where the patch panel is, or else can it be on the shelf with the other stuff? (away from the panel), and the existing D-link 4 port router?? is this no longer required?Im presuming i will need an old PC or some sort of media storage device here too... no ideas with this either. Have tried asking three different computer stores, got three different answers...?!
Have I dropped a clanger wiring to the passageway, when infact any server/switch or whatever wont be in the same location?Also, I am planning on getting a MAC book, and would like to use this on the system sometimes (might not be relevant), just thought to mention. And, I was thinking of trying Linux, as I am fed up with all the windows problems. But not sure if that is a good idea either.We have TVs in the (when its finished) media room, also three other areas, which I would like to get connected so that they will be able to get either TV or watch a film from storage wow this is getting complicated and if it matters I do have a PS3, which we only really bought to use as a TV storage system/recorder.
I've been replacing my Netgear WNDR3700 (currently only serving as wired router and gigabit switch) with an Untangle box.Obviously, only the free "Lite" version would be worth it, as the others are priced ridiculously for non business use. I've had a hard time figuring out from their webpage how the features of the "Lite" compare to the others, particularly how Spam Blocker Lite, Web Filter Lite and Virus Blocker Lite compare to the full versions of each.
Is the untangle router any good? How do its management features compare with consumer solutions?The new web caching feature seems really cool too, especially when multiple systems grab the same large updates or download the same steam games, but at $54/year it seems a bit excessively priced for home use, so I'd probably just be sticking with the base free version.
I have my asus rt n 16 running dd wrt and from there i have a gigabit run to a switch on the other end of my house i have about 5 devices plugged in and i am noticing some bottle necking with just that one run. i notice on the settings on my router i can aggregate ports 3 and 4. will this work with my switch to provide 2gbps i have a trendnet 5 port gigabit switch.
View 1 Replies View RelatedCable modem into cisco-linksys E4200. 2 of the ports going out from the router plug into the wall, where one goes to the master bedroom and one goes to the living room. Once it gets to the wall jack in each of those rooms it goes out to a gigabit switch. Each of those two rooms has a computer and a TV connected, and the living room as a blu-ray also connected to the switch.The third port going out from the E4200 router goes to another gigabit switch, which is connected to a couple more computers in that room.All of the cables are either cat5e or cat6. The long cables running through the wall from the server room to the living room and master bedroom is 24gauge 4pair cat5e, it was run by a general contractor.
When I transfer between any of the computers on the network as it sits I get 11MB/sec. I get that number by clicking more details on the file transfer. In the network tab of task manager it sits pretty consistently at 10%.If I move any of the computers to be connected to the SAME switch (i tested all 3) i can transfer around 60MB/sec.Based on this testing my initial instinct is to say that the cable running between the rooms is limiting the transfer speed. However the cable is cat5e and rated for gigabit. Neither of the runs are anywhere near 300ft long. Plus the consistency of the transfer speeds at 11MB/sec makes me think it's being clearly capped at 100base-T speeds as opposed to just slowing down due to interference of the cable.As a side note there is a place in the router that tells you the speed of each port. For some reason it has one of my ports listed as gigabit and the others listed as 10/100Mbps. The yellow 3 foot cable i have is listing as gigabit, when i swap it with another cable in the router it changes the gigabit port to the one this yellow cable is on, very odd, however regardless of whether the router says its gigabit it only transfers at 11MB/sec anyway.What I'm wondering is what could be causing this limitation besides the two cables running through the wall? Is that the only thing that could be doing it? What is the best way to really test it out? Do I need to buy some kind of network testing device that tests throughput?
Last month I decided to upgrade my network and switch everything from 10/100 to 10/100/1000 (gigabit).My setup I'm struggling with right now :
Desktop Running Win 7 x64 with a 1 gigabit NIC (running latest drivers from Intel)
Linksys E3200 Router w/ Cisco 10/100/1000 x 4 ports (Latest firmware)
USB 2.0 NAS with a WD 160SB HD 7200rpm (100MB/s)
On file transfers from the NAS connected to the Router, connected to the desktop with a CAT 5e 5ft cable, I'm pulling 9.5 MB/s MAX
Everyone I talk to say, "wow, that's what 10/100 runs" and that I'm not running one gigabit. They say I should be seeing at least 20MB/s. What am I doing wrong here? I've trying play with buffer size, settings on the NIC, MTU on the router. I'm lost at what to do.
I am currently looking to upgrade and extend my home network with preference to dual band and gigabit functionality. My problem is choosing the correct hardware.I want dual band to separate the network for the kids (a PC, laptop, Xbox 360 and phones all wireless) and set up parental controls and maintain connection speeds etc. For my needs I need the network to be connected to my Onkyo AV Amp (for internet radio and music streaming only), Blu-ray Player, Sky HD satellite box (all wired) and a PS3 (pref wired) and a few wireless devices all N capable. Apart from the obvious gaming capability I would like to be able to stream HD video to the PS3, PC (wired) and laptops via a USB HDD connected for now on an access point or modem router to save on the cost of having separate networked devices.
I currently have ADSL so I was looking to get a dual band gigabit modem router to serve the kids wireless hardware whilst my current hardware is on another floor and is connected with a wire from the existing modem but I have to keep swapping it from PS3 to amp etc.In short I am hoping to have a gigabit, dual band ADSL modem router and connect to a gigabit access point (with dual band if possible) via the cable I have sent to the other floor to wire up the 4 devices. I've currently been looking at Netgear and Buffalo solutions as I've had problems with Linksys and Belkin routers in the past. Would this be possible with just 2 devices (modem router and access point) whilst maintaining decent speeds and if so can someone shed some light as to what I should get.
After buying a new WNDR370. Sporadically and seemingly without any cause my internet will stop working. Diagnostic will always report it as "DNS Server is not responding." I've also discovered that if I enter my router settings and even just switch the DNS settings from Auto to manual or vice versa the problem corrects itself instantly-then next time it happens I just need to do it again.
I've already tried resetting my entire network and rebuilding the recommended way. Modem, Router, then computers-connecting each only after the prior has finished initializing. Hasn't worked though.
Currently I have my main rig connected directly to the modem to try and find out if I experience the problem at all this way, this is a pain in the ass though, and I don't know when long enough is long enough as the issue is completely random and simply just may not happen.
I am trying to upgrade the switches in one of the buildings to Gigabit HP ProCurve switches. Currently, this building has 3 wiring closets, and each closet has 2 Intel Standalone 460 switches (24 ports). We use them as simple Layer 2 Switches. Nothing fancy.We recently bought 3 48 port HP Procurve Gigabit switches.I was planning on going in and swapping the 2 Intel Switches out with the HP Procurve Switches. The first closet went fine, and we had immediate connectivity (servers, Internet, etc.). However, when I went to the second closet I found that I could not connectivity back to the first closet.I then noticed the patch cable going from Closet A to Closet B is terminated with a female connection on both end. And then a patch cable is connected from the end, to the switch at both sites. I have never seen this before. And I hope I am making sense. Why would this method work with the old Intel switches (that are close to 10 years old) and not with the HP?
View 5 Replies View RelatedSo I have a Netgear N600 WNDR3700 wireless router setup at home, and it works great for wireless, but when I plug in my desktop with CAT6 Ethernet cable to the router (didn't bother putting a wifi card in my desktop) for some reason it won't connect to the internet. I know the cable works because I've used it in the past, but for some reason I can't get it to work with my Netgear router.
View 7 Replies View RelatedRecently encountered this problem where one cable suddenly not working properly.We are using 568B as our standard cabling here, lines 1,2,4,and 5 are working as of checking,but lines 3,6,7, and 8 are not. Before it was working flawless. The cable are buried underground inclosed in a pvc hose.
View 11 Replies View RelatedI live in a frat and I am currently researching how to design and configure the most efficient network for the house. However, one of the other big problems we have is connectivity of our ethernet cables. We have an IT room with 2 switches that feed ethernet cables to all parts of the house and connect to an ethernet box in the wall where we can simply wire in our internet connection. We have wireless routers too but to keep the bandwidth usage across the WAP's I want to let people use the wired connections. However, many of the connection in the house do not work at all. I plug in my laptop to the wall jack and it gives me the No Internet Access notice. I don't understand why it works in some rooms and not others. All jacks seem to go into the same switches at the other end so I cannot figure out what the problem could be.
View 2 Replies View RelatedCiscowork 3.2.1 daemon manager is not working after patch installation
View 2 Replies View RelatedCiscowork 3.2.1 daemon manager is not working after patch installation.
C:Documents and SettingsAdministrator>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.
Also I checked syslog.log and it is showing below error an 17 14:39:34 127.0.0.1 100: <28> dmgt[1316]: 2507(W):Daemon manager anonymous user has not been set up: 00000569
i have no internet at all only local. But it is showing a full strength wireless signal, I have tried all the things i know plus what wdws recommended. Plus on the network tab it says its connected to an unknown network but in the manage wireless tab it shows my internet provider.
View 8 Replies View Relatedour windows PC's will connect to the home (wireless) network briefly (~15 sec) and then lose the internet connection. The wireless connection seems to stay strong. During that period any browser activity will result in a DNS error message and the Win7 network signal shows strong but not connected to the internet. We tried setting static IP addresses on the PCs but no luck. A number of PC's all running Win7 exhibit this issue.After 5-10 min it reconnects and everything is normal.Network is a 20 mbs cable based system.
View 1 Replies View RelatedI am trying to wire cat 5 jacks into my walls and none of the jacks work. I have tried with multiple jacks and experimented with different wiring configurations but they still don't work. I know the wire I am working with is good because it had a male connector on it and I connected it to my laptop before I started wiring the jack and it worked.
View 3 Replies View Relatedso I have this problem, the internet only work on one computer, whenever I connect to another computer it says something like: " Can't connect to IP 2, 3, 4 etc. I've tried resetting the modem, router and everything, it didn't work... Sooo, if I connect the same internet cable that's working on the computer to another one it doesen't work. What sholuld I do??, maybe change some settings in the router?
View 3 Replies View RelatedI want to setup port forwarding in my office router so that i can access my lan computer (192.168.0.122) from any where in the world through (remote desktop connection)I have (D-Link (DIR-615)) router. I went to virtual server option. then i select application name as Remote desktop then public port as (3389), protocol (both), Schedule (Always).My lan computer ip address (192.168.0.122), private port (same 3389), inbound filter (allow all). then i clicked save settings. Then the router took 20 seconds to save. then i close the browser.Then i asked my brother to connect through remote desktop connection who is on the skype and he is in different country and that time he is in office. So he put my router public ip address (xxx.xxx.xxx.xxx:3389) in this format but unable to connect.
View 2 Replies View RelatedMy computer runs bit torrent almost all the time, sometimes when I start Firefox the home page google never loads and neither do any other web pages yet bit torrent is still working as if nothing has changed. If I start a download in Firefox come back to the pc a few hours later Google doesn't load but the Firefox download still continues.What causes this is it DNS ?
View 2 Replies View RelatedMy roommate is running dual boot Windows XP PRO (SP3) and Ubuntu 10.10. I am running Windows XP PRO(SP3). Is there any software, that can run on both OS and can create a home network that will work between XP and Ubuntu. He has Samba installed but I have read that that works on Linux not Windows so he can see me but I can't see him.
View 11 Replies View RelatedI have a modem which is allowing me to go online at home. Unfortunately, the cable that goes with this modem is too short (just 2m).This week, I bought a cable (internet cable) of 24m and I expected to be able to move around while being connected and surf the internet but internet does not work when I am using the new cable. We have tested the cable (using a cable tester) and the cable seems to work fine. When I use back the old cable (which is very short) internet is working perfect.
View 15 Replies View RelatedI just bought and received a Cat6 200ft Ethernet cable from Amazon, linkIt is going from a router to my PC and is not working. My old Ethernet cable works just fine from said router to PC. I do not know why this one is not working. I tested the cable out on my laptop and it works fine for that. I am not sure what info to post about my PC, but I am using an Asrock z68 Extreme3 Gen3 motherboard as my lan connector.
View 10 Replies View RelatedI just moved into a house that has pre-wired CAT5 (Maybe 6) in every room. Its all connected by two Netgear FS116 switches in the attic.
According to my landlord I should just have to plug in my modem into any ethernet port, and internet will be present at every jack.
I've plugged into several of wall jacks and none of them seem to work. Sometimes for a random reason they will work, but the connectivity is so poor that I can't even load webpages. Connecting direct to the modem I receive excellent download speeds.
I am not 100% the cabling is correct, and don't know of any way to test if they are good besides plugging in my modem, and then seeing if my computer gets connectivity.
Is there some easy way I can troubleshoot this? Am I missing something major that I need to accomplish? Like go into the switch and change settings?
I used to have a WRT54G Router at home. I would regularly use Cisco Systems VPN Client to connect to my work router and the RDP to my work PC. (The router at work is Cisco 2811.)A couple months ago, I finally upgraded my home router to a Linksys E1000. Since that time, I have NOT been able to:1) Connect from my work PC to my home PC using Windows RDP2) Connect from home PC to VPN at work via Cisco VPN ClientIt's like the Linksys router at home an Cisco router at work refuse to speak to each other.A week ago, I finally gave up and bought a Linksys E3000. Exact same connect problems as the E3000.To test, I plugged my old WRT54G back in just to see, and lo and behold, all my connection problems go away. Plus the E3000 in again, and I cannot connect b/w home and work.A few other notes:From work, I have successfully used RDP to reach out to other test PCs (friends computers), but I can't get to my home network with the E3000 working. I also can connect to home via RDP using other internet connections, like if I'm in a hotel or airport.It's just that my Linksys E3000 at home and the Cisco 2811 at work refuse to acknowledge each other.
View 6 Replies View RelatedI'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup.Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC?
I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video.
With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware.
The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video).Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer.
I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma.Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration?
I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user.
I was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies View RelatedWhat are the different types of network cables
View 3 Replies View RelatedPlan a network to Connect 2 buildings 3 storey high with a distance of 500m between each building. Each floor is occupied by the Finance Department, Administration Department and Computing Department.the report should have the following items. Anything extra is encouraged.
a. Introduction
b. Network Diagrams
c. Devices that will be used.
I have a Dell Studio running windows 7 sp1. yesterday i was on the internet as normal. Today i was able to connect via my schools wifi, but not my ethernet cable. Device manager shows that my ethernet port should be available.
View 3 Replies View Related