Our Linksys WRT54GL decided to quit working.The internet works fine on all computers that are connected directly to the internet. But when the router is connected to the internet, the computer connected to it can't connect. Shows DNS server not responding in the windows troubleshooter. We are VoIP...not sure if that matters tried turning everything off for over 1 minute and rebooting in order of the modem, router, computer.
View 5 Repliesi was setting up my friends new router (Lynksys WRT54GL) and i figured out the ip address and it was DCHP(i think) enabled so i just enabled that on the router settings and then i tried to finish the setup with the disc that came in the box and it kept saying it couldnt connect to the internet.-SO-we disconnected the router and connected to the internet and suddenly, no connection to internet. it was working earlier today but for some reason now it no longer has connection. waited around for 3 hours and still no connection, through router or direct link.
View 3 Replies View RelatedI've been using my WRT54GL for a long time now, without problems. Then suddenly last night, it stopped working. Now my girlfriend said she's pushed the Cisco Systems logo/button on the front of the router (which is now orange), but that's tho only thing that's been touched. When I plug the cable straight from the computer to the internet souce, I get connectivity. I've looked at a lot of guides now, but all of them require me to turn of the modem - which I cannot do, as it's a centralized modem in my appartment block. All I have on my site of things is an internet plug in the wall. What can I do to regain my wireless internet ?
View 9 Replies View Relatedi have just purchased my wrt54gl two weeks ago. Setup was a breeze and it worked flawlessly until this morning when i noticed i had no internet. The ethernet light on my modem, when connected to router (Ubee 10C035 3.0/Comcast ISP) will blink 2-3 times then stop for a half second then blink 2-3 times and so on. Plugged ethernet cable from pc directly into modem and my desktop connected to the 'net fine and light was blinking normally(constantly) again. A few power cycles/reset of the Router to defaults but no luck.
View 3 Replies View RelatedI had the router working fine then last night for some reason it dropped 2-3 (all of them currently on) internet, while online.I can connect wireless just fine to the router but get no internet, when i plugged into the router directly i still go internet, but when i connect the modem directly into the laptop i get internet so it is not the modem. I have tried to reboot the router and modem to no avail.i can access the routers page wirelessly and change stuff but just don't get any internet and the signal strength is excellent.
View 1 Replies View RelatedI have both a Sony XBR52HX909 and a Sony BDP-S580 connected to my router (WRT54GL)via ethernet. When I try to connect to the internet, both show the wired connection as good but neither can connect to the internet. The BDP-S580 also has wireless connectivity, but it can’t connect to the internet wirelessly. I have two desktop computers connected via ethernet and two laptops connected wirelessly to the same router and all have internet connectivity. I have tried the “auto” settings on the TV and Blu-Ray player and also tried entering the network information in manually. I still can’t connect to the internet.
View 5 Replies View RelatedI upgraded my router Linksys wrt54gl with dd-wrt and i can't connect to internet now. It was all good before. Im hitting my head fo past 5-6hours and cant figure it out.
View 1 Replies View RelatedI recently hooked my router up to my cable modem and was disappointing to find my internet connection halved or worse. Here's all the relevant information I could think of.
Cable internet through JCOM (in Japan)
Router: WRT54GL V1.1
Modem: Motorola SURFboard SB6180
I have tried disabling the firewall on the router and adjusting the MTU. Both had zero affect.
Is there a possibility that installing a homebrew firmware like dd-wrt?
I'm attempting to connect an Xbox 360 console to a Linksys WRT54GL router (wirelessly), using a TP-Link TL-WA500G wireless access point. I've had this working in the past, but I didn't make a note of the configuration unfortunately. The Internet connection is connected to the router. The device hasn't been used for several months. During this time, I installed Tomato firmware onto the WRT54GL router, however I have since completely restored the router to factory defaults, by reinstalling the default firmware and performing a hard reset. Having reset the device, I was surprised to see that the Tomato favicon is still displayed when accessing the router's admin webapp.
View 1 Replies View RelatedI would like to connect my old WRT54G3G router to my new WRT54GL (connect to dsl modem) and have wireless on both activated.I have set both on different channels with same SSID and same passwords on WPA2 Personal AES.I have also made the network IP different WRT54G3G 192.168.0.99 and WRT54GL 192.168.0.98.I have also deactivated network DHCP on 192.168.0.99. and Operating mode to router and still not working.
View 1 Replies View RelatedI'm using a WRT54GL(4.30.14) Router with a Charter Cable Modem running 5 computers on the network with 1 being wired and the rest are wireless. When my family comes over they can connect with their iPads and laptops but for some reason I can not get this iPhone 4G to connect. We put in the password and it says unable to connect. Are there any special settings that need to be made to the router to let the IPhone connect?
View 3 Replies View RelatedI have my pc connected to the router with a cable. As soon as I switch it on I can't connect with any of my wireless devices like my laptop, tablet, mobile phone. As soon as I switch off the computer it works fine with all devices.
Is this a setting where the cable connected pc gets preference that I could switch off?
I can't connect my router (WRT54GL) to my new cable modem (Motorola Surfboard SB6120).
Some info:
1) Cable modem works perfectly when connected directly to computer ethernet port
2) ISP is Optimum Online
3) Using Automatic DHCP setting on router
4) Using MAC cloning on router
5) I can access the router's admin screen from the PC
6) I can connect to the router wirelessly, but no internet access
7) I've tried powering down everything multiple times, still no internet access
8) I upgraded the router firmware to 4.30.14
9) The "link" light on the cable modem never lights up when connected to the router
Recently we ordered a new Modem from Centurylink to replace an old one we have. (which ironically the old one's wireless is way better) Both modems work perfectly fine, and I've tried the same things with both to figure this out. I ran an ethernet to my gaming room, which is about 150 feet. When I connect my computer directly into the modem, my computer works fine. Initially, the PS3 worked, but when I switched back to the computer with the single Ethernet cable, I was getting an IP error. Every since then, the PS3 will not connect through Ethernet. (Wireless works, but its so far away the signal is weak)
So, I dug up my router, Linksys WRT54GL, plugged it into the ethernet that came from the Modem, (did all the steps in order multiple times), and no internet through wifi or ethernet on it. The lights and everything say there is ethernet and the WIFI/Ethernet are working, but there is no internet. All the wires are confirmed fine. I've tested them on other devices plugged directly into the modem. I tried the PS3 at the modem with 3 Ethernet cords as a test, It says there is an IP Address timeout error. Regardless of what I do, the PS3 won't connect via Ethernet. And without internet working on the Linksys router, Im getting about 15-25% signal from the Modem. (which is also wireless, if that has anything to do with the issue)
I need the router to do at the very least, WIFI. I really want Ethernet though so I don't lose much speed. (We are maxed out here at 1.5mb connection from Centurylink)
When it comes to computers, I'm advanced with them. When it comes to networking, I'm okay. I understand basic things, like accessing the router or modem through the browser. I can do the whole setup for WIFI. But when it comes to how the IP address, Static IP, etc., goes, im confused by them. So forgive me if I sound ignorant. I've looked for over a week on sites, and nothing is working. The router may be broken, im not sure. I bought it a few years ago and then didn't need it till recently. So its been sitting in a box.
All I know is, I have an ethernet from the modem to this room, the PS3 refuses to get an IP, and if I do it too much the PC gets an IP conflict. If I plug the Ethernet into the internet part of the router and do wireless or Ethernet, there is no internet coming out.
I recently had to unplug my Linksys WRT54GL wireless router when doing some rearranging and now i'm unable to get a internet connection. I've confirmed the modem is actually working by connecting my laptop directly (which worked), but when I connect the Linksys WRT54GL wireless router to my modem the internet connection goes away. The connection is lost when connected via wireless and hardwired to one of the back ports. I've tried resetting the modem, router and computer and read every forum out there trying to find something, but i'm still stuck.
View 5 Replies View RelatedI tried setting up a home network with my above Linksys router and can't connect to the internet now. I have the ethernet cable from my DSL Modem hooked into the ethernet port on the back of the Router. In port one, I have a cable which attaches directly to my laptop as I was advised to use a cable for initial setup of my home wireless network. I was able to get into the router to set all the passphrases and wireless security settings, etc. My ISP is PPPoe and I have entered both the UserId and Password that my ISP provided. However, upon clicking on the wireless icon, my system states I am connected but the status screen shows "No internet access". I have no problem connecting to the Internet when the cable runs from my DSL modem into my computer, so it's something to do with the router blocking it now.
My ISP does not support my Linksys router, of course, and they tell me I need to contact the manufacturer telling me the router needs to be set up as a 'bridge" ??? There is no mention of anything like this in the manual and I do not know if there is a setting on the router that is somehow blocking my being able to get an internet connection. This is all still with cables attached. Again, I seem to be able to 'connect' to the wireless network but I now cannot get to the Internet thru the router...
My WRT54GL Linksys modem has me stumped, it will not connect no matter what I try. it worked fine until just recently after a power outage; everything seems to be working perfectly fine hardware wise; the router shows a solid power led and network activity on WLAN, Ethernet, and Internet. I've tried soft resets and factory reset, clearing my caches, releasing/renewing IPCONFIG.
The peculiar part is that it is not letting me access the web config at 192.168.1.1 while connected with the modem, however if I plug the router directly to my PC's ethernet port I can access the config; Itried updating the firmware this way but it didn't solve the problem. I have no more ideas.
Below is the IPCONFIG information with the modem and router hooked up:
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking Controller #2
Physical Address. . . . . . . . . : 00-04-4B-17-C2-1A
[Code].....
I have router linksys WRT54gl, in my office i have cpu, phones, cameras that connected to the router lately its very slow the whole package and i think the problem is in the router i reboot it several times didn't work?i see memory used : 90% ?can this be the problem?
View 2 Replies View Related2 routers (only one in use at a time!):
(A) Linksys BEFSR41 v3.1 Etherfast Cable/DSL Router w/ 4-Port Switch
(B) Linksys WRT54GL v1.1 Wireless-G Broadband Router w/ 4-Port Switch
Both routers are set to provide DHCP.DSL modem: Verizon Westell Wirespeed B90-210015-04 I have no idea whether this modem is also a router, but everything used to work. OS: Windows 7 Professional N x64, SP1 My computer has two ethernet ports, but only one is in use at a time. I also have VMWare Workstation installed, so there are a couple virtual adapters in the mix, but VMWare is not running during any of these tests.Yesterday (Sat, 10-Mar-2012) I replaced my old router (A) with the new one (B). The A router has been working fine for many years; I just needed wireless access. After the initial setup, the B router worked fine, using hard lines connected to the switch ports, and the wireless access features (laptop and Android phone) - for about a day. It suddenly dropped the internet connection early this afternoon, Sun, 11-Mar-2012, ~1220hrs PDT. I heard it go out because I was streaming NPR at the time.Using the B router, my desktop computer (connected via a wire) can still talk to my laptop (wireless), but neither of them can see the internet.When I swap back to the A router (wires only), it now has no internet connection either! But the desktop and the laptop (both wired) can still see each other via the (wired) router.When I remove the router from the network and connect the DSL modem directly to my desktop computer, I have internet access; it works fine! But not if a router is in the circuit.
(1) Router B seems to work because my wired desktop and my wireless laptop can communicate locally.
(2) Router A still works because my desktop and laptop can communicate with each other using a wired network hosted by the A router.
(3) The DSL modem seems to work because my desktop has internet access when connected directly to the modem.
(4) Neither of the routers can communicate with the internet through the DSL modem.
I spent an hour in a chat with Verizon tech support. I've power-cycled everything. I've reset both routers to default specs and reconfigured them. I've reset the DSL modem via its button. I've used different cables. It appears that neither of the routers can successfully communicate through the DSL modem to the internet. But they both used to. Why would it just suddenly stop connecting through the modem?
Scenarios:
computer <-> DSL modem <-> internet | works!
computer <-> either router <-> DSL modem <X> internet | NoGo
desktop <-> either router <-> laptop | ping OK
ipconfig /all results when connected directly to the DSL modem (internet connected):
Windows IP Configuration
Host Name . . . . . . . . . . . . : Serenity7
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
My house was in the middle of a lightning storm today while I was out and I came back to no internet. Figgured it was just the phone lines down, but connectiong directly to the modem I found I had connectivity. The WRT54GL (flashed with DD-WRT) doesn't pick up the WAN IP, I've checked with multiple ethernet cables, 2 different modems (all of which work fine with our computers, providing connectivity) and am currently using the router that the WRT54GL displaced ~8 years ago. I'm assuming it's just dead, but wanted a second opinion... kinda odd that a surge would have come through the phone line, through a DSL modem and killed the WAN port of the router instead of taking out the modem?
View 2 Replies View RelatedI just got my fathers old linksys WRT54GL. I Have resat everything, and made my own name, password etc.When i try to connecet, i can get on the network, but there's no internet connection. Even when i put an ethernet cable between, it does the same. i have internet connection when i connect directly to the router though.
View 1 Replies View RelatedI got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
View 3 Replies View RelatedI've recently bought a WRT54GL router, and I`m having some problems with it. The original firmware the router came with had a bug, and couldn`t even connect to a PPPOE network. I downloaded the latest firmware version for this model (4.30.14 build 5, Oct. 26, 2009). Now it can connect to PPPOE but the broadband speed is limited to ~ 30Mbits/s. My ISP normally provides a download speed up to 80-90MBits/s, and if I bypass the router, and connect the internet cable directly to my PC, it works.
The QoS is disabled, so this can`t be the problem, but I searched the internet, and I found that it can be because the router`s CPU is too slow and can`t handle connections up to 80-90Mbit/s download speed, but this sounds a little bit weird to me.Did any of you gus run into this problem? Is it a hardware problem, or a software one? Maybe there`s something I need to set up in the admin interface?
i want to block all internet access on all my computers from the time range of 9 PM to 8 PM. Yes, that gives 1 hour of internet access per day. However, it seems that there are certain rules of the router that won't let me do this. It seems I can't make 2 different policies for PC's within the same IP range (192.168.1.0 to 192.168.1.254) , it gives me the error: "The values you entered are invalid. Please try again."every time I try to do so. And when I try to give the time range from 9 PM to 8 PM it gives an error stating that the end time must be bigger than start time. I am using the WRT54GL with firmware v4.30.7.
View 5 Replies View RelatedMy ISP provides me internet by pppoe connection.When testing the connection with the router i get 30 mbps.When testing the conection without the router, cable conected to laptop i get 60 mpbs.
View 1 Replies View RelatedI've had my WRT54GL for a few months now and have two computers that are wired and 3 that are wireless. I started having problems with conflicting IP's a couple days ago on one of my wired computers which was set for auto DHCP so I changed the settings and made it a static IP, this is when the problem started. I have Network Magic on all computers and even though it says I'm connected to the internet and the network, I am not able to get online. My other wired computer has been on Static IP for months and works fine.
View 9 Replies View RelatedI want to block sites like facebook during my workday but allow the rest of the internet.
The attached settings block facebook as desired during the filter times but after 6:30pm the filter expires and the entire internet is blocked (not just facebook). All of my browsers act as if they are hanging and won't load pages until I disable the filter.
I've also tried creating two different filters (one at a time). The first allowed full internet access all the time and the second allowed access the opposite times of the work filter. But to no avail.
We have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.
View 9 Replies View RelatedDoes MAC address settings allow the administrator of the router to prevent access of computers and devices to a network at will? Basically, in my household I need to have remote control over wireless devices and allow them to use the network at times and others disable it. In other words, I control when and if a certain device has the ability to use the network or not. I think I found the settings in my router when I log into it, but I'm not sure how to use them or if it even does what i described above.
View 1 Replies View RelatedI just buy a simple hub and keep my wrt54gl as my router or should I put the money toward a wireless N router (or AP) for the better range and use the wrt54gl as my hub?I currently have my wrt54gl as my one and only router.It gives me good range indoors, but I would prefer to get better range outside, if possible. Right now I get range out about 50 feet around the outside of the house but I would prefer that to double, if not more.At the same time, however, I need to move the router to the basement to better facility my network. Obviously, this will affect the wireless range.I have considered DD-WRT, but not sure it will work much from the basement.So, I have considered two options.One, I could keep my router where it is and just get a simple hub and stick it in the basement.Obviously this is the least expensive option, but it doesn't improve the current router's range, although I could try DD-WRT. The other option is I could use the money I would put toward the hub and, instead, upgrade to a wireless N router or AP and move the wrt54gl to the basement to serve as my hub.
View 8 Replies View RelatedTrying to setup a repeater down stairs for better wifi signal but am running into a problem. The main router I use for my network is a Linksys WRT54GL. The router I'm trying to hook up as a repeater is a Asus RT-N10+. The issue I'm running into is that they both use the same IP address for the web gui so when I try to configure the Asus it goes straight to my Linksys instead.
I tried to disconnect the Linksys in order to get the Asus going in repeater mode but didn't work. What I'm wanting to do is change the router IP address on the Asus so I can have both of them online at the same time to get the Asus going as a repeater. I tried to change the Asus IP but when I did it asked me something along the lines of whether I wanted to change the DHCP address being it didn't match what I had typed in as the router IP.
I flashed my WRT54GL with firmware for a WRT54G and now when I go to the configuration page all I see is this: url...I have tried doing a hard reset by doing the 30/30/30 and by using tftp to try and send the correct firmware. The hard reset does not work and the tftp keeps timing out and not sending anything.
View 1 Replies View RelatedI have Linksys WRT54GL wireless router on the top floor so the devices in one part of the bottom floor (most away from the source) are having trouble staying connected let alone getting good connection. What would be good solution in my case? I'd like something wireless, don't want to drag cables downstairs.
View 2 Replies View Related