I had to assigne my PC a new static IP address and now other computers cannot access the shared printer attached to this PC . It still show up in the printer pane of the other computers but you cannot print to it. The local PC attached to it via USB will printer fine.
View 4 RepliesI have two desk tops and a laptop and one printer. how do I share the printer?What hardware will i need? The desktops are hooked up to a cheap DSL modem router with 4 RJ45 jacks. The laptop is wireless to the same router. None of the computers are networked together, but i would like to know how to do this.
View 6 Replies View RelatedRecently I read somewhere that HP Printers have one of the highest cost of replacement ink cartridges existing. I need to buy my wife a printer. the one she has died just before I built her current PC and that was three years ago. I, myself, have an HP all-in-one printer, scanner and copier. We also have a Verizon FIOS web provider and their router, but I am not sure if I can make the web LAN share the existing printer. which new printer to get or how to set up sharing my printe.
View 6 Replies View RelatedMuch of the time my wireless printer is offline relative to computers on my LAN because the IP Address has been changed to some value different than what the computer thinks it should be. So I have to figure out what the IP Address is of the printer then modify the printer port on the PC to point to the correct address. If this only happened rarely or if I could easily remember the steps I have to take to remedy the situation, I guess this would not be such a big deal. But it happens a lot and I'm old and alzheimery. So my question is: how do I get the router to assign the same IP Address to the printer all of the time?
View 2 Replies View Relatedhow to change the IP Address on a Dell C3760dn Color Laser Printer?
View 4 Replies View RelatedI have a clean install of Window 7 64 bit Home on PC my printer is installed on. (It was previously running XP Pro) Printer drivers have been updated. I want to share Printer with Notebook running Windows 8 64 bit Home. When I added PC to Homegroup it accepted files but the printer was not listed even though I checked to add printer. Printer shows up under Network and can be seen on Notebook but can't be opened. Was getting a 0x8007035 error and now just get "window couldn't connect to the printer, check name, turned on, correct address" can't figure it out, even added ip addresses to let firewall except even though. I can see and open all files, and folders on both machines from both Homegroup and Network.
View 2 Replies View RelatedI recently bought a Asus DSL N13 router and one of the points that made me purchase it was the ability to plug a printer in via USB and all users on the network could share this printer. I double checked that my printer (Cannon IP4300) was compatible and its on the list here [URL]. I've set up the router and this work fine, both my desktop (running windows 7 64 bit) and my laptop (running vista 32 bit) can access the router and connect to the internet fine, both via ethernet cable and over wireless connection.
However I've been banging my head against a wall with regards to sharing the printer. I can connect the printer to the router and in the router configuration there is a tab for the printer server and this see's my printer (Cannon IP4300). However when i try to add a new printer on either my desktop or laptop i cannot see the printer, whatever i try!
I currently have two networks, Network A and Network B.Network A has a default gateway of 10.1.10.1 with two computers on it. I also have a router connected to Network A and this router creates Network B.Network B's router has an IP address of 10.1.10.18 with a default gateway of 192.168.1.1. Also on network B i have two computers and two printers. One printer is connected directly to the 192.168.1.1 router and the other printer is connected to one of the computers via usb.
View 5 Replies View Relatedhow can i share printer to other computers. i alreadily have 4 computers.. so ineed to share all files and software to all computers.
View 1 Replies View RelatedYou can access your home web cam via a secure routers web address.
How can you do the same with your home wireless printer?
We've got two computers in the Homegroup on our network -- call them computers A and B. Computer A (info below) is running Windows 7 Professional, Computer B is running Windows 7 Home Premium. Computer A has an ethernet cable to the router, Computer B is connecting via WiFi.
The problem is: Computer A can access files and the printer on Computer B, but Computer B cannot access Computer A. When I'm on B and attempt to add A's printer, I get a message that:
"file and print sharing device A is online but isn't responding to connection attempts"
In the HomeGroup window on A, all sharing options (pictures, documents, music, printers, videos) are checked.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Professional, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5870 @ 2.00GHz, Intel64 Family 6 Model 15
[Code]......
I have a wireless network in my house. The only printer in the house is connected to my home office desktop.I have an old HP DeskJet 672 as wells as my old Speed Stream wireless router that has a printer connection port in the back. How can I plug this printer into this wireless router thus making a family shared printer?
View 2 Replies View RelatedCan share the printer with different default gateway
View 1 Replies View Relatedhow to share printer 1022 in windows 7 to xp
View 1 Replies View Relatedi cant share my hp (laserjet3050series pcl 6) printer with my computer
View 1 Replies View RelatedHow to share a printer on lan with xp by using switch?
View 1 Replies View RelatedI have a hardwired network with 10 workstations plugged into switch. Printer plugged into switch. Server plugged into switch.Switch plugged into router.Router DHCPs except printer is static IP. All have access to internet through server then out through router.Have added another workstation that is not allowed access to the network (on purpose) but needs to be able to use the printer. The workstation is not under our security for virus control, etc so I don't want it in the server. But it needs access to internet and access to printer. Should I create a separate subnet from the router and keep the workstation separate there? If so, then how can I keep the printer accessible to both subnets?
View 1 Replies View RelatedHow can i share a usb printer conected to a windows 7 pc to other computers running windows xp and windows 7?
View 1 Replies View RelatedI received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
In a redundant Sup-6E setup, the following configuration is supported :
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
If you invoke shared backplane mode, the following configuration can also be supported:
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
Here's the command and information about the "shared-backplane" mode :- [URL]
Currently, we have 2 SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:
1- One will be used to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
My questions are:
1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?
I have a network printer that I would like to use in a room away from the router. Can I use an RJ45 splitter so these two devices can share the same cable? It doesn't have wireless capability.
View 11 Replies View Relatedi have a problem with my small office network. the issue is i have 2 public ip address that was configured in 2 (devices) dlink router and linksys cisco wireless router.
with individual static ip address:
1st router connected to dlink switch (smartweb) and 2nd wireless router is only for the admin user.
how can i able to share a files / printer with these 2 network device?
I have a Canon i6700d, which I connect to the belkin N600 USB port to share on the network. Driver for the printer is installed. From the belkin router monitor, the printer is listed under "Networked USB devices". However, the printer is grayed out and can not be selected. the dialog complains that the printer is not available.
View 1 Replies View RelatedI have a Canon LBP2900 printer. I have connected the printer with my desktop PC running windows xp and shared it. I have Ubuntu in my laptop and connected to the local network. Is there any easy way to print from ubuntu?
View 2 Replies View RelatedI recently purchased an E3200 and have successfully setup a USB printer from my desktop machine. However, I can't seem to figure out how to access that same printer through my laptop. The laptop is able to connect to the internet and the appropriate printer drivers were previously loaded.
View 3 Replies View RelatedI have an Canon MP 530 that works great for my home office network, but right now it's being shared off one of my PCs. I would like to network it like my HP LaserJet P2055dn, but not just printing, also fax and scan (via Adobe Acrobat Pro). Does this product really exist.
About two years ago I bought a Linksys device that turned out to be a $100 mistake, but now I'm really needing this sharing functionality.
I have 2 desktops (running windows 7), a Canon MF8300 printer, and an outgoing ethernet line, all on a Netgear Advanced Cable Modem Gateway CGD24-CPR. I'm only concerned with having the 2 desktops set up with the Canon printer.Both computers have been connected to the printer before and I have the startup disk. But once the new offices were set up and both of the desktops were moved, I can no longer access or find the printer.
I can IPconfig the Desktops for their IPV4 addresses and both desktops recognize eachother on a Homegroup, but I can't find the printer. I printed off the print configuration page from the printer which gave me an IP address (printer is set for auto-obtain), but using an IP search won't bring up the printer.All of the devices are plugged into ethernet ports set up for the three different office they are in and the actual location of the Netgear cable modem/router is over 100 feet away. My primary concern is getting the printer for the desktops, but I also need to add a wireless router into one of those office in the future.
I used WPS on my DIR-655 Rev B1 FW 2.03NA to register a Brother HL-2270DW Wifi laser printer and my Mac can never wake it up to print. It always works fine from all my Windows machines.It appears as xxx.xxx.xxx.6 on my network. But the router only shows its IP as 0.0.0.0 on the STATUSWireless page and I can't find any way to change that. My assumption is that the Mac can't find it because of this, but I'm not an expert on WPS.Maybe I should take it out of WPS and just assign it a fixed IP using DHCP Reservation. Or is there another fix? I haven't ruled out the Brother OS X printer driver, but it and the printer's firmware are both up to date.Two odd things:
1. I can ping the printer from my PCs but the Mac can't find see in and it's not a Firewall issue.
2. I can see the brother printer in Finder's Shared devices: so it sees it but refuses to interact.
I've finally gotten tired of Netzero Dialup and want to change to dsl from U Verse. That brings up some questions. Do I cancel Netzero when I start U Verse or do I need Netzero to make it work? If I have to cancel Netzero can I transfer my favorites over to dsl? How difficult is it to set up dsl? Does the box come by UPS of Fed Ex?
View 6 Replies View RelatedI tried changing the WEP to WPA because I recently found out our neighbors were stealing internet from us. However after doing all this changing around I used 192.168... And all that and was able to change the ssid and the passphrase but after doing so the Internet stopped working. We are able to connect but it says there's no service or limited connectivity so no web pages or anything loads. Now I can't get back to the router page by typing that 192.168. stuff because there's no Internet. Don't know what to do. This is my fathers ISP and it's not the greatest considering the location. I've tried unplugging the router and whatnot but that's not working either. I think we need to get back on the router page and fix something but it's not allowing us to since there's no Internet. Am I going to have to change back to a WEP.. I dont really want too. The router may need to be upgraded too because it's pretty ancient.
View 4 Replies View RelatedA router restart. I changed the wpa to wen so I could connect my ds to wifi.So far what I have done was restart the modem, it's a Cisco wag120n. This is a wireless so the moment I changed to wen, I lost connection. I then used a cable to connect to the modem and managed to change the settings in the router page 192.168.1.1 back to wpa but with no success connecting to the Internet. I then tried ressetting the modem and computer with no luck. I cut the power to the modem router and turned off computer for 5 minutes. I then turned the modem back til it was stable and then the computer, again with no luck. I then factory reset via the button manually and via the modem page but both ended up with the unable to connect to primary DNS server.
View 6 Replies View RelatedI have been trawling the interenet looking for an answer to the i but to no avail.Can you change the source port that windows uses when it makes a connection to another host.
[code]...
My exchange server should have an outside interface ending in .82 which is one of public IP's assigned to it.Inside 192.168.168.250 -> Outside x.x.x.82 How can I configure this in ASA 8.4(1)?
View 3 Replies View RelatedBack in may, I built my own gaming rig and have been using wireless on it all the time. But recently my speeds has been going down, and i can't be bothered to fix it. That's why i wanted to use ethernet on it. My problem is that there is only one port on my modem for Internet, and that is being used by a routher that goes upstairs.
As you can see, i have three TV ports and one PC port. All of it is being used.One of the TV ports goes trough the wall too a exit in my wall, and goes into my TV Router as seen on the image below.