A router restart. I changed the wpa to wen so I could connect my ds to wifi.So far what I have done was restart the modem, it's a Cisco wag120n. This is a wireless so the moment I changed to wen, I lost connection. I then used a cable to connect to the modem and managed to change the settings in the router page 192.168.1.1 back to wpa but with no success connecting to the Internet. I then tried ressetting the modem and computer with no luck. I cut the power to the modem router and turned off computer for 5 minutes. I then turned the modem back til it was stable and then the computer, again with no luck. I then factory reset via the button manually and via the modem page but both ended up with the unable to connect to primary DNS server.
I tried changing the WEP to WPA because I recently found out our neighbors were stealing internet from us. However after doing all this changing around I used 192.168... And all that and was able to change the ssid and the passphrase but after doing so the Internet stopped working. We are able to connect but it says there's no service or limited connectivity so no web pages or anything loads. Now I can't get back to the router page by typing that 192.168. stuff because there's no Internet. Don't know what to do. This is my fathers ISP and it's not the greatest considering the location. I've tried unplugging the router and whatnot but that's not working either. I think we need to get back on the router page and fix something but it's not allowing us to since there's no Internet. Am I going to have to change back to a WEP.. I dont really want too. The router may need to be upgraded too because it's pretty ancient.
Our ISP provider made our internet connection a dial up. Last time it automatically connects to internet without putting those username and password. So after they changed it only our server pc have internet. Others don't have. The technician from the isp provider keep telling that the switch(but he keeps telling us its a router dunno why) need to be configure but switches dont need to be configure right?
I have two separate wireless networks in my house, one of them is for sharing my NAS data and the other is for Internet.problem is when I connect to the NAS network and after that I change my network to the other network, I can not connect to the internet ( I can connect to the wireless). Just after restarting I can see the Internet
I recently set up my DIR-615 on my wireless netbook. Everything worked fine and I could get online. But then when I changed the password on the router, it bumped me off and now says Internet isn't available. My phone can connect to Internet but not my netbook anymore. When my netbook tries to troubleshoot it keeps saying "problems with router and adapter."
I am a newbie regarding mobile IP.the meaning of the phrase "changing the link-layer point of attachment to the Internet, yet without changing its IP address".
I used BT previously without any problems but now use Orange and now using the Internet downstairs is useless(weird flat configuration). The router is upstairs, next to TV(same location as the BT router). I dont know why the wireless Internet signal has become very weak. The only way I can use the Internet if I sit a few feet from the router. Even then, streaming videos on youtube still takes a while compared to BT. This affects all devices using wireless connection - even my Iphone is useless when used downstairs.
Signal interferance/ hacking? Router? Wireless adapter is up to date.
well i had the same problem because i got bored and i was like hmm i wonder if i can change my IP and i tried it and i had the same problem but when i did system restore it still did not work, now i have to get a new operateing system...
I recently changed my graphics card (geforce 9100 to radeon hd 7750) because i wanted to enjoy some simple gaming and my previous graphics card (geforce 9100) wasnt capable of doing so. (This is my pc : HP Pavilion p6100 Desktop PC series*-* HP Pavilion p6130y Desktop PC Product Specifications - c01748306 - HP Business Support Center ). Before changing the card i uninstalled all nvidia related drivers (both in control panel and device manager) because i heard thats what youre supposed to do.
I successfully changed my graphics card (i think...) i can run all the games that i couldnt run before but.. I am having trouble connecting to the internet after changing the card. it seems like my computer isnt recognizing the inernet network. i know the network is fine because im writing this w/ my itouch which is connected to the network wifi. When i right click the red X icon w/ two computers and click "connect to a network" , it says "windows cannot find any networks" and i have no network options to choose from. Is it because i uninstalled drivers related to the network connection..?
If I have a wireless network set up with the Linksys E1000 using one internet provider and then change the internet provider service to someone else, do I have to reset up the network or is it simply a matter of connecting the new internet service to the router?
I've finally gotten tired of Netzero Dialup and want to change to dsl from U Verse. That brings up some questions. Do I cancel Netzero when I start U Verse or do I need Netzero to make it work? If I have to cancel Netzero can I transfer my favorites over to dsl? How difficult is it to set up dsl? Does the box come by UPS of Fed Ex?
I have been trawling the interenet looking for an answer to the i but to no avail.Can you change the source port that windows uses when it makes a connection to another host. [code]...
I had to assigne my PC a new static IP address and now other computers cannot access the shared printer attached to this PC . It still show up in the printer pane of the other computers but you cannot print to it. The local PC attached to it via USB will printer fine.
My exchange server should have an outside interface ending in .82 which is one of public IP's assigned to it.Inside 192.168.168.250 -> Outside x.x.x.82 How can I configure this in ASA 8.4(1)?
Back in may, I built my own gaming rig and have been using wireless on it all the time. But recently my speeds has been going down, and i can't be bothered to fix it. That's why i wanted to use ethernet on it. My problem is that there is only one port on my modem for Internet, and that is being used by a routher that goes upstairs.
As you can see, i have three TV ports and one PC port. All of it is being used.One of the TV ports goes trough the wall too a exit in my wall, and goes into my TV Router as seen on the image below.
Everyday a few of the computer will error with "A duplicate name exists on the network:" A quick Google search shows the same answer EVERYWHERE on the internet. So I changed the names of a few of the computers too something I knew was unique. Still though the problem persists/ it afters the two XP bases computers the most, but my main workstations (windows 7 sp1) has had this error a few times, although it appears to have left for a while. I have a feenas server but Active directory is not turned on.My router is a e4200. I was using DHCP server on there (and would very much still like to) although I have turning it off, rebooted both the router and the computers but to no avail.
Every so often (random amounts of time) my internet setting either on the router or pc change and then I it comes up with an error that my settings aren't the same as my router... I use a Orange Live box and windows 7. also when I want to sign into games for windows that sometime crashes the internet and on DOW2 and minecraft.
I tried changing my ip address using ipconfig / release. I tried to fix what I did using ipconfig /renew but it tells me no operations can be performed on local connection 5 while it's media is connected.
I play this hockey.tk game. I want to change my ip to a different nearby state. For example, If I live in new jersey i'd want to change my ip to New York so I can play the game. How do I change my ip to that? For some reason I got ip blocked on a game.. So I was wondering if there was any way to do that
I am trying to configure a router with a satellite connection. I am following a HughesNet guidline. At step four after typing in the required IP address , nothing happens.There is no place to type user name and password.
I am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
how to change the ARP timer in CISCO. I know how to change th mac-address aging timer, but can't seem to find any documents on how to change the ARP timer from 4 hours.
I found this good guide how to do it, but some things remain unexplained to meI would like to get more information about step:3. Change the IP address of your current PCMaybe more questions will follow, but that's the only problem I am having right now.
I need the capability to log into the 3g/4g modem and change the Wan IP address. Doe anyone know of a 3g/4g modem that allows you to do that. My other option would be to disable the wireless radio on the 3g/4g router and connect my Linksys Wireless router that I know I can log in and change the WAN Ip. It looks like to me that this model below would allow me to do that?MBR1516 Will turning off wireless radio on the 3g/4g router completely turn off all routing or could there be a conflict with my Linksys wireless router?
I am currently facing a major problem. I am a user of the Smart FTP software and have several files in it.However, the "Sites" folder is showing a blank screen. It shows nothing, when there are supposed to be at least 30 files.
I think I have discovered the cause of this; the "Read" permissions are off. Here is where my problem comes in, when I enable it and select "Apply Changes Recursively", it goes back to the unchecked "Read" permission. It doesn't seem to take into account the fact that I want to enable it.
