Recently i bought Dlink 150 router and configure sucessfully for the Toshiba satellite laptop when i am trying to connect the status is showing as connected sucessfully but iam not able to access any URL with wirless And the same dilink router when i configure another laptop it is working fine so i a came to know there is problem with my Laptop
View 4 RepliesI am try to setup my office network to able to connect to one of my customer HQ via site to site VPN. I am using Cisco 1841 router to do the job.
The problem that I am facing now is no able to connect my other PC in office to the remote site.
show crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
202.x.x.x 175.x.x.x QM_IDLE 1001 ACTIVE(code)
I am having issue with network connectivity between remote access (RA) VPN users and remote site VPN hosts.
Topology is:
RA VPN laptop (192.168.200.3 /24) ---- internet ---- Head Office (ASA5505) -- LAN subnet 10.0.0.0 /24
SiteB (10.0.10.0 /24) ---- internet ----- Head Office (ASA5505) ---- LAN subnet 10.0.0.0 /24
From head office there is no issue communicating with RA VPN and siteB hosts but Site B hosts and RA VPN users can not communicate each other totally (ping failed too).
Site B is using Cisco 867 router with IPSEC VPN to the ASA5505 at head office. I have added the ACL on this router to access 192.168.200.x /24 for VPN traffic and exempt from NATing. When I enabled ' drop log' in the class-map in the Zone based firewall config, I could not see any ping packt comes in so I believe the issue is at ASA5505 config.
At ASA5505 I use split VPN tunnel ACL and have included the subnet for 10.0.10.0/24 as well as 192.168.200.0 /24. This split tunnel ACL are applied to both the IPSec VPN tunnel and also the RA VPN group policy. The ASA is using sw version 151-4.M5.
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
We have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
I have a dynamic VPN site to site between ASA 5510 vs C880 with segment 172.23.191.0/25 for ASA side and some host in C880 side (e.g. 128.1.100.211, 128.1.115.181, 128.1.104.212) . The VPN is up, but only have communication with a host (128.1.115.181).
In the logs appears the next message when I try communication for all aother IP in the policy map configuration: IKE Initioator unable to find policy: Intf Inside, Src: 172.23.191.87, Dst: 128.1.115.182..ONLY WHEN I PINGING FROM SOME HOST IN C880 SIDE (e.g. 128.1.100.211) the communication is successfull.
What happen with this VPN, because I need to pinging from C880 IP host to ASA segment for establish communication?
I am configuring Site-to-Site VPN with another company. I already make a couple of tunnels but with this one I have a problem. They I already using on their side my local network 192.168.10.0/24 (server is 192.168.10.10) so we need to use imaginary network 172.16.0.5 as server address. Now I need to do NAT 172.16.0.5 to 192.168.10.10 but I am not so good in that.
View 1 Replies View RelatedI am unable to ping any device on the internal lan from the opposite side of the tunnel. However, the tunnel connects successfully. I have the firewall disabled on both routers. Site A is using 192.168.3.1 and Site B is using 192.168.4.1. Any thoughts on why I cant ping one router from the other?
View 4 Replies View RelatedI can't open a connection to eca-msp.crashplan.com (which is one of the data servers for the CrashPlan backup service).Symptom: "telnet eca-msp.crashplan.com 443" hangs, and eventually times out.
Works fine when I connect directly to my cable modem.No PC or device behind my firewall can access it when going through firewall.Other crashplan hosts (notably, central.crashplan.com 443) work just fine.And of course, every other https site I use works just fine.
[code]....
I have a Belkin F7D2301 v1 (01) and I am having the exact same issue. I like to do surveys and I've never been able to access this particular site It does the same thing as the original person's problem. I'm kind of scared to change anything on my router setup because I have several computers on the same router. Will any of this cause the other computers not to run on the router?
View 2 Replies View RelatedI have a new WRVS4400N configured with a site to site VPN to connect to my office. At the office, we're running a Cisco PIX 515E. I have successfully established an IKE preshared key and the tunnel is listed as Up. I can successfully connect through the VPN tunnel into the office network through the tunnel and all seems good. After some period of time, the tunnel apparently goes into a bad state. Access to the office network is no longer available. When looking at the VPN status screen, the Linksys indicates that the tunnel is up. However, I cannot ping any resources on the office lan. If I disconnect and connect the site to site VPN tunnel, it connects and comes back up successfully. It seems like there is some sort of timeout taking place here. I am running the 1.1.03 firmware.
View 7 Replies View RelatedI setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I've spent 2 days already trying to get 2 ASA 5505's to connect using an IPSec vpn tunnel. I cannot seem to figure out what im doing wrong, im using 192.168.97.0 and 192.168.100.0 as my internal networks that i'm trying to connect over a directly connected link on the outside interfaces with 50.1.1.1 and 50.1.1.2 as the addresses (all /24). I also tried with and currently without NAT enabled. Here are the configs for both ASA's, the vpn config was done by the ASDM, however i have also tried the command line apporach with no success. I have followed various guides to the letter online, starting from an empty config and from factory default. I have also tried the 8.4 IOS. [code]
View 2 Replies View RelatedI have a problem trying to connect a VPN site to site between a FWASA 5515X - ASA5510. [code] The configuration in the 5510 its the old one that i been using with a firewall 5505.
View 1 Replies View RelatedAfter upgrading a couple of AS5505 to asa8.41 and using ASDM-641 I have been unable to set up a Site to Site using the Wizard.Had enough of a headache doing the upgrades on the CLI. I wait for my PO for Sec+ to clear so I can Add Failover. Ping was enabled and both '05 can ping each other. [Code] .....
View 1 Replies View RelatedI recently used my dad's Acer Aspire 5040 and saw that he was using xp service pack 2. I thought i'd do him a good turn by putting service pack 3 on and now i can't get it to connect to the wireless router.At first it was saying "you are connected to this network" in the list, but still saying "Not connected" in the top right.I thought it may need updated drivers so I have installed everything from the Acer site, including the Atheros Client Utility.
Now, when i use the auto settings it defaults to the ip 169.254.161.135 with the default gateway the same, but my router gateway is 10.1.1.1. so it says it has limited or no connectivity.I try to change the settings manually and everything goes green and says connected but it still wont access the internet or ping the other computers.I have tried resetting the router as I thought it may have been that not resolving DNS addresses but my netbook is connecting to it fine.
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
View 3 Replies View RelatedI have just purchased and successfully installed a wireless Belking router and although my pc connects perfectly my daughter cannot connect to the same router even with the correct security codes, what are we doing wrong
View 1 Replies View RelatedFrom My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedI can not get my new hp pavilion g series laptop to connect to the wireless router that I currently have. What do I need to do?
View 1 Replies View RelatedSo here is the issue:
When I connect my modem directly to my computer (modem > computer) it works just fine, internet connects and everything through the direct ethernet connection.But when I connect the modem to the router and then try to connect wireless with any other computer (modem > router > wireless) nothing works. Not even when I have it connected directly from the router to the ethernet on the main computer. (Which has ALWAYS worked until now.
Just to set the stage, we used to have a network which ran in the following order:
For wired workstations: bridged DSL modem->wireless Linksys E900 router->Dell PowerConnect 2824 switch->2 modular 4-port jacks->individual workstations For wireless: bridged DSL modem->wireless Linksys E900 router->workstations The workstations were set up to pick up IP addresses automatically.After an infrastructure upgrade where we added some Cat6 cables and swapped the modular jacks for a patch panel, we lost all connectivity. I restored the connectivity to the wired workstations by assigning IP addresses. But we have no wireless and I cannot access the router GUI at its IP address (even when plugged directly into the router). All the workstations show the default gateway as 192.168.10.1, so I don't know what's going on.
I have a Cisco Linksys router that I have been using for about 6 weeks just fine with Windows Vista on an Acer Laptop. We had some power outages (about 3, less than 30mins each) and the internet was down for nearly 48 hours early this week. Now that it is up, I was able to connect to my router for a few hours. When I shut my laptop off and about 2 hours later tried to access the web again, I found that I couldn't unless I hardwired from the modem.I've done the windows repair network connection and the Cisco Network Magic fix- (It says things like flushing DNS cache while doing its thing). Both say my network key is wrong. No one else in the house could have changed it, I was the only one home.I've power cycled both the router and modem. I've turned my laptop off and rebooted. I used the manufacturers settings to try to go in and see what happened. I can't type the router's direct IP and get into like it says I should in Firefox.
The one thing I've noticed is that prior to the outage- my router had a "name" that I named it, while now it's back to linksys_numbers_letters. However, I was still able to connect after the outage at the beginning.
Just purchased a ea4500 router. Have setup multiple computers/devices already and works great. This computer (HP dv6000 running Win Vista home prem) however will not connect to the internet. It states that it is connected to the router (computer sees router), using the cloud connect app on my iphone i can see this computer, but will not allow access to the internet (local connection only). It works fine with the wired connection. When attempting to use the cloud connect software, it says it was unable to complete the install. Have attempted trying while connected by wire as well, same result. Have deleted the wireless connection and allowed software to find connection, still same result, cannot install. Wireless worked perfectly with previous router (WRT54G) three days ago.
View 6 Replies View RelatedMy e1000 was working fine until it was accidentally unplugged. Now it doesn't work. I downloaded the set up program from the site and tried to run it, but it does not recognize an internet connection when I have the modem connected to the router and the router connected to the PC. The internet works when I connect the modem directly to the PC. I have unplugged everything and restarted the PC several times and tried running the software again, but no dice.
View 4 Replies View RelatedI my parents have a WRT54G linksys router, they have a DSL modem. Everything was working fine with the wireless network until one random day POOF! the wireless no longer would connect on laptops. However, the internet is working just fine with the computer that is hardwired up throught the router. Since this is working it lets me know that the router is working fine and routing the connection through hardwire. Hard wired works on laptops but all laptops are unable to join the network and most of the time it will not show up in the list of available networks.Even my iphone wont connect saying unable to join network. We bought a brand new linksys router and same problem. I then took his old router to my house and hooked it up...and WOW it works as it should all devices can connect...even my iphone.
View 2 Replies View RelatedI just bought the EA6500 last week. Had to RMA it on Monday and got the new one today. The issue still persists. The power light is constantly blinking and my computer is unable to obtain an IP address from it. I contacted tech support and was unable to get the issue resolved so I had it exchanged believing it was defective. The new one does the same thing. When I connect my computer to it, the light on my Ethernet port stays a solid orange instead of green like it does for my usual router. The Cisco light is constantly blinking.
View 9 Replies View RelatedChecked cable router (brighthouse), working. Router (all lights on but network traffic flashing indicates one way traffic). So I go to my wife's computer. It too has no connection. I open my laptop to connect to the wireless, IT WORKS! Pull power on Cable Modem and Router, wait 60 secs, power up Cable Modem and then power up Router (I know it wasn't nec to do modem but I wanted a clean start). Wireless is still working, no LAN. I can't even connect 192.168.1.1. Linksys software says it can't detect the modem. Reset time, hit the magic button in the back and sure enough everything stops working (which I figured). Still can't connect to it, and now I've lost wireless. I connect computer directly to Cable Modem and type this message. Seems to me that Router has failed.
View 3 Replies View RelatedI have a VirginMedia 50Mps wireless router that runs 4 wired connections. These are all working fine and have Internet connection. When the router was installed I could also connect to the internet wirelessly on my Laptop which is running Windows Vista Home Premium. But of late I have been unable to connect to the Internet on the Laptop. When you place the mouse pointer over the Icon in the bottom right hand corner, the following message comes up : Currenlty connected to:Unidentified(virginmediaxxxxxxxx) (where xxxxxxxx is a numeric identifier for the modem). Access: Limited connectivity or sometimes it says Access : Local only.
View 4 Replies View RelatedI am unable to connect to the internet through my wireless router. However, I can connect using neighbor's wireless connection and other laptops in my home are able to connect to the internet using MY wireless connection. The problem started suddenly, I used to be able to connect, then I had the problem so I rebooted and that resolved the issue temporarily. I tried disabling the wireless adapter card then rebooting, this did not work. I also unchecked the TCP/IPv6.
View 4 Replies View RelatedMake and Model Cisco DPQ3212 (Modem)Netgear N600 Wireless Dual Band Gigabit (Router)So when I first got the router and modem and hooked it all up everything worked. Then the inter got shut off for a day then came back on and now the only way I can use it is by Ethernet cord. This would be fine but, unfortunately the Xbox in in the living room nowhere near the router. I have tried power resets and everything else the companies of both tell you to try but nothing is working.
View 8 Replies View RelatedI have a pretty basic NETGEAR router right now. I have a Zyxel modem that Centurylink sent when I signed up for my DSL service. The Zyxel modem connects to my NETGEAR router. When I play online either wireless or wired from the Netgear modem I have major connection issue.However, if I disconnect from the netgear modem and connect from the Zyxel directly to the ps3 I have zero problems.
View 19 Replies View Related