I have a Belkin F7D2301 v1 (01) and I am having the exact same issue. I like to do surveys and I've never been able to access this particular site It does the same thing as the original person's problem. I'm kind of scared to change anything on my router setup because I have several computers on the same router. Will any of this cause the other computers not to run on the router?
View 2 Replies
i cant login to my belkin f7d2301 v1 router tried fac reset
View 1 Replies View RelatedI have a belkin f7d2301 and I cannot access the startup menu it says startup not found I have remove program and reinstalled it. is the disc bad. i also cannot do auto updates because it can't find startup location.
View 2 Replies View RelatedI have this problem yesterday when I was surfing the internet when suddenly my belkin router turns off. This router is working just fine in the beginning when we have this. When I troubleshoot, it says about the ethernet cable. When I plug it to the ethernet slot on the back of my computer, it would not flash an orange light. Am I required to buy another ethernet cable or it's just my router who had just lost power?
View 5 Replies View RelatedHardwired into the modem speeds are great...wireless speeds drop down to half.
View 1 Replies View RelatedWe have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
I'm setting up a site-to-site VPN between two offices, Site A uses a Cisco RV110W VPN Router with a static WAN IP and local IP 192.168.1.0/24 while Site B I have set up with a Belkin N300 VPN router which also has a Static WAN IP and the local IP is set to 192.168.2.0/24
I'm able to ping from Site B (192.168.2.xxx) to Site A, however I can't communicate from Site A back to Site B.how I could go about troubleshooting this? I've been scouring the internet for 3 days trying to get to the bottom of this with no luck.
Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.
View 2 Replies View RelatedI recently purchased a DLink DIR-815 router to replace my aging Linksys. The router works great, except that I can't access my ISPs website, nor their IMAP server. I can access every other page on the web. If I connect direct to the modem, or through my old Linksys it's fine, but with the DLink I'm having problems. Internet is DSL using PPPoE. The net info from the status tab is:
Local address : 206.248.167.xxx
Subnet Mask : 255.255.255.255
Peer address : 206.248.154.104
Primary DNS Server : 206.248.154.22
Secondary DNS Server : 206.248.154.170
ISP web page is at 206.248.155.70, and mail server is at 206.248.188.90 I have reset the router to factory default, and setup the PPPoE, and still the same issue. I have also tried using the DMZ but no luck. ISP can't seem to figure out the issue, and points to the router configuration.
I am having issue with network connectivity between remote access (RA) VPN users and remote site VPN hosts.
Topology is:
RA VPN laptop (192.168.200.3 /24) ---- internet ---- Head Office (ASA5505) -- LAN subnet 10.0.0.0 /24
SiteB (10.0.10.0 /24) ---- internet ----- Head Office (ASA5505) ---- LAN subnet 10.0.0.0 /24
From head office there is no issue communicating with RA VPN and siteB hosts but Site B hosts and RA VPN users can not communicate each other totally (ping failed too).
Site B is using Cisco 867 router with IPSEC VPN to the ASA5505 at head office. I have added the ACL on this router to access 192.168.200.x /24 for VPN traffic and exempt from NATing. When I enabled ' drop log' in the class-map in the Zone based firewall config, I could not see any ping packt comes in so I believe the issue is at ASA5505 config.
At ASA5505 I use split VPN tunnel ACL and have included the subnet for 10.0.10.0/24 as well as 192.168.200.0 /24. This split tunnel ACL are applied to both the IPSec VPN tunnel and also the RA VPN group policy. The ASA is using sw version 151-4.M5.
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedI have N600 HD Wireless dual band N Router. have successfully installed the router on wireless mode, however I have the following problem in accessing the storage devices connected to the Router.I can see the storage devices connected to the Router in the "Belkin USB Print and Storage center", but when I double click to browse the devices, it does not open up.
View 1 Replies View RelatedI am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
I am try to setup my office network to able to connect to one of my customer HQ via site to site VPN. I am using Cisco 1841 router to do the job.
The problem that I am facing now is no able to connect my other PC in office to the remote site.
show crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
202.x.x.x 175.x.x.x QM_IDLE 1001 ACTIVE(code)
I have a dynamic VPN site to site between ASA 5510 vs C880 with segment 172.23.191.0/25 for ASA side and some host in C880 side (e.g. 128.1.100.211, 128.1.115.181, 128.1.104.212) . The VPN is up, but only have communication with a host (128.1.115.181).
In the logs appears the next message when I try communication for all aother IP in the policy map configuration: IKE Initioator unable to find policy: Intf Inside, Src: 172.23.191.87, Dst: 128.1.115.182..ONLY WHEN I PINGING FROM SOME HOST IN C880 SIDE (e.g. 128.1.100.211) the communication is successfull.
What happen with this VPN, because I need to pinging from C880 IP host to ASA segment for establish communication?
I am configuring Site-to-Site VPN with another company. I already make a couple of tunnels but with this one I have a problem. They I already using on their side my local network 192.168.10.0/24 (server is 192.168.10.10) so we need to use imaginary network 172.16.0.5 as server address. Now I need to do NAT 172.16.0.5 to 192.168.10.10 but I am not so good in that.
View 1 Replies View RelatedI am unable to ping any device on the internal lan from the opposite side of the tunnel. However, the tunnel connects successfully. I have the firewall disabled on both routers. Site A is using 192.168.3.1 and Site B is using 192.168.4.1. Any thoughts on why I cant ping one router from the other?
View 4 Replies View RelatedRecently i bought Dlink 150 router and configure sucessfully for the Toshiba satellite laptop when i am trying to connect the status is showing as connected sucessfully but iam not able to access any URL with wirless And the same dilink router when i configure another laptop it is working fine so i a came to know there is problem with my Laptop
View 4 Replies View RelatedI have just purchased and successfully installed a wireless Belking router and although my pc connects perfectly my daughter cannot connect to the same router even with the correct security codes, what are we doing wrong
View 1 Replies View RelatedO.S - Windows Vista
Router - Belkin F5D8236-4
When I check with PFPortChecker, it says "We were not able to ping your router" I have done everything correctly, or maybe I thought I have. I have try 69.165.255.1 a default gateway but it just goes to Unidentified Network and I can't access the Internet
So i got time warner cable and internet but for some odd reason a "wired" connection works perfectly fine but i cannot get any life out of my belkin n750 DB wireless router. ive hooked it all up modem to router to pc nothing so i reset everything still nothing
View 3 Replies View RelatedI configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies View RelatedI've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic. When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.
View 5 Replies View Relatedwe have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
ASA = 8.2(1)
ASDM = 6.2(1)
Recently I used the wizard to create an IPsec site-to-site connection, which went very smoothly; however, I now noticed that when I connect via Anyconnect 2.5.0217 I cannot get to local and subnatted resources on the network.
I rolled back to saved config file, which was taken before the site-to-site vpn was created, but that did not work as well.What should I check to see why I can no longer get to different subnets after the site-to-site vpn connection.
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host. How can I set this up?
View 33 Replies View RelatedI have a Cisco 2911 router configured with a couple of VPN tunnels . The issue that I am having is that I cannot access the servers (WEB,EMIL) thru the tunnel . After looking around found out that adding a route-map to my static NAT rule will fix the issue . Once I do that I am able to access the serves thru the VPN but my local machines lose internet access .So I have to delete the access list The issue seems to be with the Access list 110 permit ip [code]
View 5 Replies View RelatedHow can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have four hosts say: 10.240.1.1-10.240.1.4
They need access to two different networks:
205.100.150.0
140.175.200.0
I woud like to NAT them as something like:
7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4
I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.
View 6 Replies View RelatedCan I use a single Public IP address for both Internet access and site to site vpn access?If not, can I configure the RV220W as a bridge and still use it via another gateway configured for vpn passthrough as a VPN appliance/server on the LAN?
View 3 Replies View Related
