for some weeks now, Im searching for a solution to stream live video from a wearable device (glasses, headset) to a windows system for recording. Requirement is complete freedom from <span dir="auto">any LAN[CODE]
View 6 RepliesI am attempting to connect a video streaming device to my wireless network and it will not accept what I think is the password
View 1 Replies View RelatedJust got a new HD Smart TV and trying to stream Netflix and Youtube. Netflix works decent most of the time, buffering occasionally but Youtube buffers all the time and is not watchable. Using a Netgear WGT624 b/g router located some 60 feet away a half floor upstairs. Internet downstream speed is about 5.5 Mbps on the hard wired main computer and laptops show the same speed when connected wirelessly. Wireless Network Connection Status on a laptop close to the TV show "Very Good to Good" signal strength and Speed at 11 Mbps. Why is the Yotube connection so poor on the TV? The Netflix could be better too. Laptop by the TV streams Neflix and Yotube fine but of course that is not HD. Do I need an upgraded router or powerline network adapter?
View 1 Replies View RelatedActually i need a streaming server that supports both audio(mp3) and video formats(mp4,avi..).But it should work in multicast and should possible to stream with VLC media player.now i'm trying helix media server.In this what are the procedures to configure helix sever in multicast.and how to stream media from it.Or Any other streaming server is there that suits for my need.
View 1 Replies View RelatedI am trying to setup the QoS for my router, and want to bump up the priority for streaming video such as Netflix, Youtube, and others... I am not certain what specific protocols and ports are used for streaming though. Googling Configure QoS for Youtube comes up with tons of long winded articles that never get to the point...
View 1 Replies View RelatedI have been trying to stream videos from my PC to my Xbox 360 via the Windows Media Center app. I've got it all set up, my PC detects the 360 just fine and vice-versa. However, when I go into the app on the 360 and select the video to play, it plays it extremely pixelated. Usually it just freezes up on an extremely pixelated frame while the sound of the video continues on as normal. I've tried MP4, MKV, AVI, WMV, etc. all at multiple resolutions all with the same result.I can stream just fine via HBO, Netflix, Amazon, etc. so I don't think it is my network or internet speed. I've tried putting the 360 on a static IP, I've gone through all the FAQ from Microsoft about enabling Windows Services and the like, none of which has made a difference.I am able to stream to my PS3 just fine, so I am not sure what is going on with the 360.
View 3 Replies View RelatedI am about to buy a NMP (WD Live Hub) to put my local video/music/pic content on and drive many TVs in my house. These NMP also have services like Hulu, NetFlix, etc. I plan to sign-up for NetFlix and do the unlimited streaming thing via the WD Hub. I have a 5Mbps broadband pipe which is right at the suggested level for HD streams.....but I think the DIR-655 can prioritize streams/video ?
plan to put the Hub on Static (Reserved) IP address on my network....however, I've never messed with a Router and prioritization. I assume it is something to do with the port(s) used, etc. I have no idea the ports that will be used by the Hub for NetFlix, how/where in the DIR-655 I can accomplish this how to ID the ports used would be great....eg. some variant of Netstat command, etc ?
i've lost the ability to view live streaming video (adobe flash, i think) on several websites. it happened gradually over several weeks and now videos will not load. the dir-615 has functioned flawlessly over several years but it might be showing its age now. connecting directly to my com cast broadband modem fixes the problem. can i tweak the router settings or do i need to replace it?
my setup: dir-615, H/W Ver. E1, F/W Ver. 5.00NA, two wired connections to X Box's and one to Win 7 PC. wireless connections to several Win 7 laptops and other tablets/phones. com cast high speed broadband with their Norton security suite.
if replace.....i need a recommendation. the best bang for a buck while staying within a tight budget.
I have some internet users who listen to online vedio music and and other streamin program so my network goes very slow and bandwidth consumtion is goes very high.in this situation i have no any firewall, how i can stop vedio streaming by cisco 2621 router.i have been configured to stop the bittorrent and it successfully done class-map match-any peer-to-peer match protocol gnutella match protocol kazaa2 match protocol fasttrack match protocol novadigm match protocol edonkey match protocol bittorrent match protocol rtp match protocol rtsp!!policy-map peer-to-peer class peer-to-peer drop?
View 2 Replies View RelatedI have a persistent any very annoying issue that the router reboots on it's own when I am streaming video from Netflix or other similar applications.
I read some reviews about this router which stated that this was a known problem, but apparently was resolved with latest firmware updates.
My router is new (less than 1 year). It came originally with the 2.0.1.2 firmware which I updated to the 2.0.1.3
That did not resolve the problem. So my question is, is there any aditional configuration necessary to stream video without interruptions, or, is this a hardware problem?
Movies on external hard drive connected to desktop pc. Sony bdp-s580 player. The router is a Netgear wndr3700 v3. Sony bluray player connects to the internet with powerline networking device (hence not wireless)Or would it be easier to simply disconnect the usb hard drive from the desktop pc and connect it directly to the bluray player?
View 2 Replies View Relatedlooking to pick a good managed gigabit switch for my central media server implementation.I will have probably 10-12 tvs connected to this along with other things like ip pbx extensions, music streamers, ip cameras etc.Now I can imagine about 2-3 tvs simultaneously streaming HD quality movies. In that case, I am assuming I will need a minimum 150-200mbps throughput switch. Is my assumption wrong?I have been looking at some switches which seem nice and relatively inexpensive but the throughput is much lower than that.If I wouldnt need that kind of throughput then can you explain me how do I come up with my max limit.I initially thought that since its going to be a gigabit switch it would be able to handle that kind of traffic through all its port at once, but I guess thats not a correct assumption. Throughput is what reall dictates simultaneous maximum? Am I correct?
View 1 Replies View RelatedMy computer is a HP Laptop Model Number DV2815EA running windows vista 32 bit. Its a few years old. Recently i have had problems with my wireless adapter turning itself off whenever i watch videos online. It doesn't happen all the time, but if i am watching something for more than an hour it will cut off. There is a blue light and a switch on the front of the laptop, and when the wireless adapter is off, the light changes to red.
The light will change to red sometimes whilst watching video, and the only way i can turn the wireless back on is if i restart the system. Even if i activate and disable the wireless adapter using the external manual switch, or the internal controls using the wireless assistant. Also, not sure if this is relevant but i can no longer either watch videos on full screen as the image gets jolty.
Things i have tried:
1) restoring the system to a previous restore point - i tried this but for some reason the only restore points i could find were ones dated after i started noticing the problem.
2) reinstalling the wireless adapter driver and video card driver.
3) running a full 6 hour antivirus scan - I am using Eset NOD32 antivirus and also i scanned using comodo cleaning essentials.
I have just upgraded from an E1000 to the E3000 and have run into a couple of problems with my iphone 4s.There are a few applications, BBC iplayer, Sky Go, BBC News and ITV player that wont allow me to watch any of the online video through the iphone. I have iplayer on two other computers running through the same router and they work fine.Every thing worked fine with my old E1000 so I'm taking it that it must be a setting in the router itself somewhere that needs to be altered to allow it to work.
View 6 Replies View RelatedI am facing issues with my router EA4500 and my apple TV. When I am watching a video from my itunes library at my PC, sometimes stop playing waiting to receive data. Is that a way to conect my apple tv to my router to prioritize this video streaming from my PC to apple TV?
View 9 Replies View RelatedI have been having a problem with my 4400n dropping connection when streaming video / audio.It is connected half duplex to a cat2950 and the media server is mediatomb on a linux box the client is a ps3 presently.
View 3 Replies View RelatedWhen I try to stream a movie through the media server or through my computer to my xbox 360 the video will play fine for a couple minutes then it well get choppy and then the sound will not sync with the picture. I have the latest firmware and reset it also. Tried switching channels and changed mtu didn't do anything. tried steaming on 2 different xboxs and its the same thing.
View 3 Replies View RelatedI am having wireless connection/internet issues that are irritating me to the core!!! I have called tech support 4 times now, and I still can't get everything to play nice...I have the 655 set up as a wireless router to a Windows 7 laptop, one iPad, two iTouches, and one N3DS. I can't find a setting that will work with all devices. Here are the senarios...
1) Settings: Wireless enabled, 802.11n only, Auto Scan off-channel set to 1, Best Transmission rate, Channel Width Auto 20/40, Visible, Auto WPA Mode with AES Cipher and a pre-share key. This yields fantastic results with my laptop, it can stream video for entire episodes, and I have no problems with loading webpages in either IE or Firefox. However, it does not support the kids iTouches or N3DS.
2) Changed the above to mixed 802.11n/g AND ALSO tried 802.11 only: iTouches work and can connect to the internet, but laptop doesn't like it. I get "Problem loading webpage" every other time I access and website, and streaming stop every 5-6 minutes. Bars indicate wireless signal is strong, but intermittently get that yellow triangle.
So I am trying to forward a port on my linksys E2500 router. I need to forward 198.162.17.3 for a video streaming server. When I go to the admin panel I am only able to change the last digit, ie 198.162.1.x
View 5 Replies View RelatedVideo streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?
View 3 Replies View RelatedHow do I setup this on the SRP527W? I already block most of the video stuff on the internet. But I want to make this one more step.
View 1 Replies View RelatedIs there anyway to convert a laptop (with inbuilt wireless device) to a streaming device via wireless connectivity?Essentially I have a desktop and also a laptop in the house. I sometimes want to use my desktop in other places in the house, since my laptop is seriously old, I have most of my work data on my desktop. SO, I thought the idea of being able to use my laptop as a streaming device, acting as a wireless monitor, keyboard and keypad.
View 1 Replies View RelatedSetup my DCS-930L for DDNS (Dynamic Domain Name Server) so I can access the DCS-930L via the Internet (couldn't access the camera half the the time while on vacation using mydlink) and can now access the camera using my laptop, Android Thrive, and Motorola Droid 3 via the URL I've created but can only see the video when using the laptop.
I have the DCS-930L set to Java but when I log into the camera with the Thrive or Droid 3 (both Android devices) I don't get video. I can make changes to the camera settings and everything else you can do when logged into the camera but just can't see the video. If I change the 'View Mode' in the video setup to 'Image', I will get a picture on all three devices (Thrive, Droid 3, and laptop).What do I need on the Droid 3 & Thrive so I can see the video when I log into the DCS-930L with an Android device?
is there any way of getting the DCS-2121 cameras to register as a windows "video" device? I am running windows 7 and would like to use the remote cam as a video device in a desktop app - Microsoft OCS.
View 1 Replies View RelatedMy BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies View RelatedWe are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedI have some 1080p video files on my PC. Since my PC isn't powerful enough to play the files smoothly, I have been streaming the content to my PS3 using Windows 7 media sharing.
This works well with no noticeable loss of quality.
My problem is that I have to go into the services on my PC and restart the WMPNetworkSvc service every time I switch the PS3 on, otherwise the PS3 doesn't detect the PC.
how to make this a permanent arrangement?
Everyone speaks about video and music streaming, however I am under the understanding that there isint actually any such thing as legitimate real time streaming, ALL files are saved to the disk or the RAM. If this was not the case, disrupting your Internet connection would cause an instantaneous crash of the streaming media, and well, I have had my Internet crash a lot of times while viewing streaming median and in every case it continued to play for some time.
View 5 Replies View RelatedWe have a server with lots of home videos on. We currently run HFS so that the files can be accessed by anyone on the home network and download them.
What software would I use to be able to stream the videos in realtime through a browser?
All I'm trying to do is play music files stored on my PC upstairs with my Dune Media Player downstairs which is part of my home cinema system. The Dune player is hardwired ethernet via Homeplugs and can "see" my PC and media library and the folders in there, but everything shows up as empty - photos/music etc. The Dune will "see" a netbook we have via wireless and displays the contents no problem. Netbook is running XP Home and the PC Win 7 64bit.Initially, all worked in that the Dune player saw the Win 7 PC and libraries. I could do a slide show of photos and see the music files but couldn't play them - unsupported Codec. All my music on the PC is lossless and in WMA Lossless format to make things easier when using WMP12. However, nothing really supports this format and most devices prefer FLAC/ non Microsoft - and here's the collision. WMP12 doesn't like FLAC - even with plug ins I've tried, it's hard work.Decided to dump WMP12, clear libraries and wipe it's database. Installed Mediamonkey version 4 instead as this will do all I want - apart from maybe photos. Have transferred some FLAC albums over to Music Library and Mediamonkey gets all artwork etc and plays them. Have enabled Mediamonkey to act as a UPNP server and it's running. However, the Dune Media player still sees empty folders in the PC Libraries - music and photos. All the folder are shown such as All Music, Albums, Artists etc, but there's nothing in them.When clearing WMP12 library and database, I stopped Windows Media Player Sharing Service in services.msc.I have restarted this in case it makes a difference. No change.
why can't the Dune Player (or Roberts Internet DAB radio we have) see what's in the library folder when using Mediamonkey. It's the same using WMP12 with FLAC files. It did see everything when WMP12 was fully loaded and set with WMA Lossless - but the codec isn't really supported by anything other thanm Microsoft.
I have a custom built media server with 2 dual digital tv tuners in.I can record TV and stream it to computers on the network fine, but is there anyway I can stream a Live TV stream to multiple PC's? I have heard of it being done, but can't remember where I read it.
View 1 Replies View RelatedI'm currently looking for a fast, non-wireless router. My current router is cutting down on my download speeds(Yes, I have forwarded ports, disabled firewalls etc.)Musts: Gigabit ethernet, preferably no wireless, relatively cheap I can disable the built-in firewall completelyIt will mainly be used for surfing, downloading and streaming of high quality movies.
View 7 Replies View RelatedIf i can stream films form an external hard drive connected to an xbox 360 without the aid of a pc effectively using the xbox 360 as a nas.
View 2 Replies View Related