Cisco RVS4000 Setup As Gateway
Aug 30, 2011
I have a side client who's recently upgraded their internet service from a single T1 to a 100mb fiber line. TW Telecom brought the fiber line into their building and run it through a Cisco 3400 which hands it off to TW Telecom's Adtran 4430. If I take my laptop and assign it the appropriate IP and subnet and plug straight into the Adtran I get close to full speeds so I can rule out the ISP (I think).
It comes out of the Adtran to a Cisco RVS4000 setup as a gateway and then feeds off to a Cisco SG200-50 and Cisco 248G switches. Anything from the RVS4000 and beyond on the customer side will only receive a quarter of the speeds I get if I plug straight to the Adtran. I talked to the tech from TW Telecom and they have confirmed the Adtran is hard coded for 1GB Full Duplex speeds so I'm going to assume the RVS4000 needs to match that. I'm not 100% sure on how to make sure the RVS4000 is set to that. In the Admin GUI for the RVS I've gone under the L2 Switch Port Settings and set them to match the Adtran but it makes no difference.
I'm getting some sort of port duplex conflict and need to figure out where to make adjustments.
View 8 Replies
ADVERTISEMENT
Oct 17, 2011
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies
View Related
Apr 8, 2012
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies
View Related
Jan 29, 2012
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
SUBNET: 255.255.255.0
Local Security type: subnet
LOCAL IP: 10.10.10.1
SUBNET: 255.255.255.0
[code]....
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
Apr 4, 2012
I am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies
View Related
Jan 4, 2012
I have a RVS4000 connected to my cable modem which I use as my gateway, the IP address of the RVS is 192.168.3.254
I have a 2811 with 3 subinterfaces of which I can ping all of them from my PC which at the minute is in VLAN 1, the only network that can connect to the outside world is VLAN 1, how can I enable the other 2 vlans to connect to the internet?
My set-up details are
Router
interface FastEthernet0/0.1
description *** Data Network***
encapsulation dot1Q 1 native
[Code]....
View 1 Replies
View Related
Nov 11, 2012
I am getting ready to setup an RVS4000 so we can use the VPN functionality of it, but I am not quite sure of the correct way to integrate it into our network though. I do not need site to site, just the client portion of it for a few salesmen/off site people to use. I have never used or setup a VPN before, so I'm learning everything as I go along.
We are in the middle of switching our ISP and I am waiting to set this up until the new service is live so I can test it prior to moving the rest of the company to the new ISP.
We are switching to Comcast, and will have 5 static IP's available to use. Currently, the firewall does all our NAT and is the forward facing device on our network. I would like to leave the firewall in place (although I am setting up a new firewall for the new internet connection) and have th RVS 4000 sit behind it and receive VPN traffic from a WAN to LAN rule We currently have a 192.168.100.0/24 network.
Do I need to setup another /24 network for the VPN to function behind (and still have access to the 100.X network), or is there a way to allow everyone who connects to receive a 100.X ip address from our DHCP server. I'm not sure how to set everything up with the WAN/LAN connections on the RVS4000 to acheive this.
We are running a domain on a 2008R2 server. The clients will be using laptops that are already part of the domain, if that will make a difference.
View 2 Replies
View Related
Aug 23, 2012
I have a Cisco RVS400 router at my restaurant. In lan ports 1-3 on the router, I have plugged in my point-of-sale computers.Into LAN port 4 I have plugged my wireless access point that is in my dining room.
The wireless access is there ONLY for the customers to access the internet. I want to make sure the customers cannot access my company data, can this be accomplished through the use of VLANs ? If so, how do I do this? All of my devices are configured for dhcp..if that's relevant.
View 2 Replies
View Related
Sep 25, 2011
I just purchased a RVS4000 after chatting with a Cisco rep. I want to set up a router at my office (RVS4000) that I can connect to from virtually anywhere with my iPad, log into a server on my network and run a Remote Desktop service. The Cisco rep. told me that the RVS4000 was exactly what I needed. So here is what I've done so far:
iPad(192.168.2.67)-->192.168.2.1(wirless router)-->Internet-->RVS4000-->(192.168.1.1)-->\Server(192.168.1.33)
On the RSV4000 VPN tab IPSec VPN:
Tunnel name: Office
Local Security Type: IP only
[Code].....
View 4 Replies
View Related
Aug 6, 2011
I have succesfully config an IPSec VPN Tunnel by using a Router Scientific Atlanta Cisco 2320 and a RVS4000 4-Port Gigabit Security Router with VPN.On the site of Router Scientific Atlanta Cisco 2320 this is some info: [code] On the site of RVS4000 4-Port Gigabit Security Router with VPN this is some info: [code] Remember that you can not be on the same range of IP, I mean, you can not have 192.168.0.X if the remote network is on 192.168.0.X, you have to change some of the Routers.I show the configuration on Router Scientific Atlanta Cisco 2320: I show the configuration on RVS4000 4-Port Gigabit Security Router with VPN:If all is correctly configured, you should see on Router Scientific Atlanta Cisco 2320 the Status Connected:
If all is correctly configured, you should see on RVS4000 4-Port Gigabit Security Router with VPN the Status Up.As you can see, I'm connected to the remote Router (RVS4000 4-Port Gigabit Security Router with VPN) by my own web browser accesing by the local IP 192.168.0.10.I have used Authentication MD5, maybe is not the best one but I had no time to test SHA1, I will when I will have time.
View 1 Replies
View Related
Apr 24, 2012
I have a RVS4000 and I am going to configure vlan in the near future. Among all other configurations sent by the internet provider company is this one :
Firewall NAT :
from x.x.2.0/24 to 0.0.0.0/24 should be NAT
from x.x.2.0/24 to x.x.0.0/21 should not be NAT
From all the other configurations, this one is not clear to me. Can this configuration be done on a RVS4000 and where can it be done.
View 1 Replies
View Related
Sep 13, 2011
I have a home network with an Actiontec Q1000 providing me 20 meg down and 5 meg up speeds. The DSL modem supports DHCP, DMZ, port forwarding, application forwarding, filtering, etc. I have an existing network 192.168.0.x that uses a combination of DHCP and static IP addresses for printers, scanners, and servers.I just purchased a RVS4000 and configured its LAN port to accept a DHCP address. It received the .26 address. I set up application and port forwarding so all VPN traffic goes to this address. I also put the router in the DMZ and turned off all firewalls.On the LAN side of the RVS4000 I use the 192.168.1.x address and have the 4000 provide DHCP addresses. I have a PC connected to the LAN port and it has the address of 1.100. I am able to use TeamViewer to connect to this through the internet and I can also access the devices on the Actiontec network from the PC connected to the 4000.I set up the VPN as best I could while going through appendix B of the admin guide. When I am at a remote location and use the QuickVPN client to access the 4000 I get the message, "The remote gateway is not responding. Do you want to wait?'. When I look at the log everything looks good except I get the following error:
[WARNING]Failed to ping remote VPN Router!
I am unable to get a DHCP address for my remote PC and am unable to ping any device on either network. What do I have configured wrong that this is not working?I only purchased this so I can use the VPN. Is the VPN established on the Actiontec LAN or on the RVS4000 LAN side? I am obviously connecting to the 4000 but am just not getting an address so I can not use my home office network for all my communications.
View 1 Replies
View Related
Jan 24, 2013
We share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies
View Related
Jul 21, 2011
I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
View 1 Replies
View Related
Nov 6, 2012
I gave setup a vpn gateway between two cisco RV120W. The connection is established.
Active IPsec Security Association Table: Policy NameEndpointPacketsKBytesStateActionRxTxRxTxVPN-INTERDIO87.65.38.62000.000.00IPsec SA Established Poll Interval: (Seconds)
The problem is that there is no trafic. Even ping te remote internal nework is not working. For testing i have disabeld at both sites te firewall and have configured both with an access rule any to any.
View 1 Replies
View Related
Apr 7, 2013
I am trying to setup the following. We have an RV042 Router and are using it as our gateway at the office. In the office we are using a Windows Domain abc.lan with DHCP of 10.0.0 - 10.0.0.254. The Router/Gateway is setup with a Static IP of 10.0.0.100.A couple of our office employees would like to work from home via VPN using their laptops. With the many options available for this router, I am not clear as to which options and what settings I should set.
View 2 Replies
View Related
Dec 1, 2012
I've just installed a standard Cisco wireless install (5508, 3502i, local and flexconnect setups) all working swimmingly.
The customer has asked for a new WLAN for a particular group of staff that will route to a different gateway than the general wireless staff.
The 5508 is connected to a older Avaya L3 switch that is the customers core swtich, but it isn't capable of PBR so it routes on desitnation only and its default route is not where I need the new WLAN traffic to route to. An ASA will be connected to the Avaya switch (which is the alternate gateway I need to get the new WLAN users to). So my question is probably routing 101, but if the ASA interface, the Avaya swtich and the WLAN interface all reside in the same VLAN, can I give the wireless clients the ASA as their gateway via DHCP and successfully get their traffic to the ASA?
View 3 Replies
View Related
Dec 2, 2012
So i am trying to Set up a wireless repeater so i can have a better signal in my back yard but i could not set the configurations for my repeater because the gateway (ip address? Not really sure what it is called) would not work when i entered it into the browser. So i went into command prompt to make sure i had the right gateway and it did not even exist.
View 6 Replies
View Related
Jun 25, 2012
I have a Linksys WAG200G wireless ADSL router. So it has one ADSL(phone) line input port , 4 Ethernet ports and wireless router. My router is fine and works well on ADSL connections. But as I have switched to Comcast DOCSIS modem based internet connection now, I want to to setup this router as "Home Gateway" only and not the modem. My intention is to use- use 1 of the 4 ethernet ports at the back of router as an INPUT . I want to put the ethernet output of the DOCSIS modem into this INPUT- and then i want to use the remaining 3 Ethernet ports as OUTPUT ports from the router.- I also want to work my router as Wireless router.
My query is- Is this possible ? Basically use 1 port as an input and 3 as output.- I have tried different things - Using Bridge mode only. DHCP disabled but sometimes only wireless works and other times only LAN bridge setup works but both do not work together.- Also at times, one Ethernet port will work as an INPUT and 1 as an OUTPUT but other two remain disabled.
View 4 Replies
View Related
Jan 22, 2012
We can not find the gateway on our Dell Latitude D810 we were able to locate the IP address and Subnet Mask however the Gateway info does not come up we have tried various times to connect to a hotspot no problem with our Dell Latitude D620 and the Function Key plus the F4 key does not bring up the wireless prompt.
View 1 Replies
View Related
Feb 14, 2013
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
View 2 Replies
View Related
Aug 30, 2012
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies
View Related
Jul 6, 2012
I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
View 7 Replies
View Related
Sep 13, 2012
config setup
protostack=netkey
klipsdebug=none
[Code]....
View 3 Replies
View Related
Apr 11, 2013
I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies
View Related
Mar 9, 2012
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
View 2 Replies
View Related
Feb 11, 2012
I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
View 2 Replies
View Related
Mar 19, 2013
I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?
View 1 Replies
View Related
Jan 24, 2012
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
View 1 Replies
View Related
Jul 11, 2012
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
