I am using packet tracer 5.3 version and I am trying to configure IGRP on it but it doesn't show me igrp under routing protocol selection.Router number is 2621XM.IOS version is 12.2.learn the configuration of IGRP.
View 2 Replieshow to unlock the config tab in packet tracer?
View 1 Replies View Relatedi have made a topology in packet tracer related to etherchannel configuration.i am using 2 3560 switches and 1 2950 switch. Now what i want is to bundle up the redundant links between these 3 switches. The links fa0/1-3 between 2950_1 and 3560_1 switches have been bundled up but when i try to bundle the links fa0/4-6 of 3560_1 to fa0/4-6 of 3560_2 it wont work. i am using channel-group 1 mode desirable between the 3560 switches. secondly if i want to assign ip to port channels then it has to be of same subnet between 2 3560 switches right and it must be same between 2950_1 and 3560_1. But these 2 subnets should be different from one another.
View 3 Replies View Relatedi'm on the CCNA 4 accessing the WAN part for the Cisco Academy. I'm trying to do a packet tracer 8.6.1 and I'm stuck. I'm looking for the answer so I can figure out what I'm missing.
View 1 Replies View RelatedHow can I pair a html file to a domain name in packet tracer?
View 2 Replies View Relatedhaving some issues. My basic VOIP network I can get to work no problem uner Vlan 1. But when I try tomake multiple basic networks to connect and put them in to diffrent Vlans such as Vlan 2, 3, 4 and conect them the phones now say configuering IP.
View 1 Replies View RelatedI'm trying to set up a network comprised of three LANs connected by serial. As this is a small part of an assignment I've been instructed to subnet into /26 and to use /30 subnets for my serial connections.At the moment I can ping between devices on each of the LANs but I can't ping between routers at all. Embarrassingly I'm not sure why, I think it may be something I've missed on setting up the serial links as I have set routers up fine before using other connection types.
View 12 Replies View RelatedI'd like to know if packet tracer 6 can be download yet?
View 5 Replies View RelatedI'm preparing myself for CCNA exam and i started doing a lot of different examples. I've got problem with Packet Tracer when i'm trying to apply some security settings for the range of switch ports in default VLAN 1. I might just demonstrate my commands so it will be easier do understand.
View 2 Replies View RelatedI am trying to test PIM SM mode between some 2811 routers built up in my packet tracer 5.3.3 .But surprisingly PIM option is not coming in the interface mode .Even IP multicast option is not shown in global config mode.
View 6 Replies View RelatedI have been playing around with Packet Tracer trying to understand EIGRP and to put it into practice. Well im not doing so well, I cant get the routers to form an adjacency therefore nothing is pinging outside of the routers. [URL]
View 4 Replies View RelatedI'm an IT student and I've been assigned with homework simulating a network including an ISA server and some clients in Packet Tracer but I can't find anything which can be configured like an ISA (Internet Security and Acceleration) server(this is kind of Microsoft's technology as I know) in Packet Tracer, the generic Server from the devices box has only some basic services such as HTTP, DHCP, DNS, FTP, AAA, ... but none of anything related to ISA, all the servers in Packet Tracer have only 1 interface whereas the ISA server (as far as I know) should have at least two interfaces, and there is also no CLI supported for those servers so I think I can't simulate ISA server in Packet Tracer, can I?
View 4 Replies View Relatedhave 2 routers connected in cluster ith serial dte link. screenis locked. I need to draw a topology of Internet cluster, but i don't know how to discover whats is in it, because i don't have set ip
View 2 Replies View RelatedI have a project about ISP in packet tracer,I want to know how to make firewall configuration and steps I don't know how to use firewall in packet tracer at all.
View 1 Replies View Relatedusing packet tracer, how can i find dns server ip address and i am having trouble pinging the desktops and server that i manually assigned the ip addresses to
View 2 Replies View RelatedI'm trying to create a silent, scripted install of Cisco Packet Tracer 5.33. At the end of the install there is a box that comes up about Packet Tracer Skills Based Assessment (PTSBA). Is there a way to supress this dialogue box? I'm using "PacketTracer533_setup.exe" /sp- /verysilent /norestart" with no luck.
View 2 Replies View RelatedI'm student from IT school and i have a school project but i have a problem on packet tracer.In a vlan, i must block the communication between computers in it but i dont know how i must do that.Effectively, it's about 250 computers in this VLAN but each computer can't caommunicate between us.
View 4 Replies View RelatedAsking about Packet Tracer. I currently use packet tracer 5.3.2.Can you give me any link where to download router template on packet tracer? I want to explore cisco 2821 but packet tracer 5.3.2 has an existing of cisco 2811 only then, I tried to add the 4 ports of RJ11 but I cannot see the 4 port telphone.
View 4 Replies View RelatedI am unable to get traffic from any VLAN to communicate outside of the router, as well as get any traffic from outside of the router to communicate with any device on either VLAN. I am able to ping the router from each device on each VLAN, and vice versa. However, the traffic seems to die at the router, and I cannot figure out why. I know it's probably a small, easy fix, but I cannot seem to find any kind of documentation on it.
View 13 Replies View RelatedI am trying to troubleshoot a problem where in one of my remote site is not able to access some networks at HQ over Site to SIte VPN ( asa 5505 at Remote and 5520 at HQ). I ran packet tracer and HQ ASA looks clean as everything came out as ALLOW. Remote site ASA packet tracer give me DROP out at Phase 9 (VPN). I am not very sure what to look in ASA for resolution now. Is it an access list that is blocking the traffice or VPN setup.
View 5 Replies View RelatedI've been using packet-tracer for some time on and off with mixed results.
I'm running a multi context firewall with over 10 of the contexts sharing the same outside interface / network. All interfaces obviously have valid, unique IPs and also unique MAC addresses as mac-address auto is enabled in the system context.
This is an ASA 5550 running 8.3(2.10) interim so includes the fix for the well known packet-tracer classication failed bug.
So in theory, with firewall contexts on a shared interface the ASA should use the firewall MAC address to classify incoming traffic to the correct firewall and as far as I am aware, only fall back on using NAT to classify if the interface MACs are the same. In reality on my platform this doesn't seem to be happening and the classifier is using NAT to determine the destination context. I'm seeing this with live traffic (i.e. not generated by packet-tracer) in logs and can prove it by disabling certain NAT rules (there is some overlap with the IP addressing behind each firewall).
My question regarding packet tracer is this - in the above scenario with a shared outside interface, does packet tracer ALWAYS use NAT to determine the destination context? Or does packet tracer look up the MAC address of the ingress interface according to what context you are running packet tracer from? It appears that packet-tracer is using NAT in my case which could be just symptomatic of the potential bug I've described above rather than by design.
here, am used to the RouterSwitch CLI but been asked to set up an ASA 5505 8.4.Quite simply I am trying to at least test out a static PAT from an external source to an internal server in a test environment and no matter whether I set it up as an auto-nat or a twice-nat whenever I run a packet tracer I end up with the same error. This is the packet-tracer I am running-packet-trace input outside tcp 80.80.80.80 3389 10.240.0.10 3389
Phase: 5
Type: NAT
Subtype: rpf-check
Result: DROP
Config:nat (inside,outside) source static server publicIP service RDP RDP
Additional Information:
[code]....
Now I have a couple of questions initially. I have made the presumption that packet-tracer does not look at any external devices while running - as in as long as the ports are up it doesn't matter what is on the end of them for testing purposes? Is there anything I am missing?I have this morning wiped the config and have simply set up the adapters, a default route and twice nat and am not sure why I keep getting the error. I am sure it is something very simple and I'm being a massive donut!
[code]...
I am using Packet Tracer to simulate Cisco networking.As the existing IOS of the 3560 and 2960 switch are in older version which has no new feature in new IOS, how to upgarde the IOS of Cisco switch at Packet Tracer?
View 5 Replies View RelatedI'm studying for CCNA Sec exam and looking for any security labs for GNS3 or Packet Tracer.
View 3 Replies View RelatedI have one server which run some application for wireless user. this server forward multicast packet to wireless user. server and wlc physically connect to cisco 3750 switch.i want the server forward the multicast packet to wireless users.server access vlan 4.wlc controller have 2 vlan: 90 and 110.and wireless user some of vlan 90 and some of vlan 110.i enable igmp snooping on wireless controller. and enable globally command but it is not working.which additional configuration i need on cisco switch.
Switch(config)# ip igmp snooping
i connected 2 routers 2621xm with serial and setup. but i didnt need the RIP cuz i just sent msg/packet from RT2/Laptop2 to RT1/Laptop1 and it saids SUCCESSFUL RECEIVED. so whats wrong with my 2 networks?why passed through from rt2 to rt1 without RIP configuration?
View 3 Replies View RelatedI am not sure if the issue I have is due to router's performance of my configuration. Currently I have 2621XM connected in my internal network where Fa0/1 is considered untrusted zone and Fa0/0 is considered trusted. It appears that traffic is limited to about 3.17MBps (Mega Bytes) between Fa0/0 and Fa0/1. There are ACLs on the Fa0/1 inbound and Fa0/0 inbound. I am also using ip inspect rules for the Fa0/1 outbound traffic. When I remove ip inspect policy from the Fa0/1 interface, the traffic speed bumps up to about 4.8MBps (which is about 38Mbps - Mega bits).
Each time the CPU utilization is: CPU utilization for five seconds: 99%/99%; one minute: 19%; five minutes: 4% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
Access to the router during that time is veerrrryyyyyy slow! Does this mean I am hitting the maximum limit this router can handle?
I've got a 2621XM that has not been used for a while.Completely stripped of any modules and configuration files, the router will continually cycle the startup process without actually booting from the IOS.
The cycle displays the following :
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10034ec
What I've tried:
1) Downloading another IOS image (c2600-is-mz.123-20.bin) via Xmodem and running "confreg 0x2102" from the rommon. All that did is change the last message to "program load complete, entry point: 0x80008000, size: 0x10fa95c"
2) Running the command "boot flash:c2600-is-mz.123-20.bin". If I enable the diagnostics via rommon, the cycle expands to:
System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)
Copyright (c) 2003 by cisco Systems, Inc.
program load complete, entry point: 0x80008000, size: 0x10fa95c
Testing lower main memory - data equals address
Testing lower main memory - checkerboard
[code]....
If it wasn't for the lack of error messages, I would assume it was a hardware issue.If the image was corrupted, I would expect a message indicating that the image couldn't be read.
I'm trying to login to my cisco 2621XM router. I'm using putty and I can't remember the how to cable it or the settings to use in putty. I don't have a db9 input on my pc, so I need to go through my NIC. What type of cable to use, what port to plug it into on the router, and what settings to use in Putty.
View 1 Replies View RelatedI have a Cisco 2621XM router with two ethernet interfaces that sits before a vendor supplied VPN router. I need to see the IP traffic incoming to my router from the WAN side (fasteth0/1 below). I setup ip cef, and ip flow ingress on the interface. However -- it seems that what I see when I use "ip cache flow" command doesn't have a very long history or life. What commands am I missing so that I can see a summary of the stats over say the last 5, 10 or 15 minutes? Is this the best config that can be used for this, or can I create a more summarized report just using the router HW and IOS? Basic current configuration:version 12.3service timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname Littleboy!ip subnet-zeroip cef table event-log size 1024ip cefip cef accounting per-prefix non-recursive prefix-lengthip cef traffic-statistics load-interval 180!ip flow-cache entries 2048ip flow-cache timeout inactive 60!interface FastEthernet0/1 description Littleboy to vpn-wan ip address 10.1.0.1 255.255.255.252 ip flow ingress?
View 5 Replies View RelatedHow to setup dynamic dns for Cisco 2621xm ? What IOS support Dynamic Dns?
View 3 Replies View Relatedwill the AIM-COMPR2-V2 will work with the 2621xm
View 1 Replies View RelatedI have an old 2621xm router in CCIE lab at home. Only a week ago I started having issue on 2 of them. The problem is on one of them when I go under interface configuration and I type "no shut" nothing happens. Interface stays in administratively down status and when I check running config "shutdown" is still under interface.
On the other one the same problem but only with "router rip" command. I configure my rip routing but then when I check running config there is no rip section and also RIP is not running under "show ip protocols rip".These routers are connected to 2511 AccesServer. So I thought the issue might be communication from AccessServer to these devices. I connected a console cable straight to them and still the same problem. Everything else is working on these devices.