Can't Connect To Internet Through Router - Red Cross On Network
Aug 25, 2011
I can connect with no problems through my ordinary internet cable but not when I instead connect it to the router and I put a cable between the router and computer. Then a red cross appears between my "Network" and my "Internet" and it says "there may be a problem with your domain name server" when I try to repair it. I can access the router settings by going to 192.168.1.1 but I don't know what to change. It's a Linksys WRT54GL and I'm on a windows vista. I've tried stuff like reseting the router and doing ipconfig /flushdns but no success.
View 9 Replies
ADVERTISEMENT
May 4, 2011
How to connect a pc to pc with cross cable
View 2 Replies
View Related
Oct 11, 2011
I'm trying to find a single device that can both handle Q-in-Q VLAN trunk termination and also TDM cross connects between DS0's on a multi-channel T1 card and DS0's on a multi-channel DS-3 card. I'm looking at a Cisco 7606-S with SUP720's. If I install a 7600-SIP-200 or 7600-SIP-400 with both a SPA-2XCT3/DS0 (channelized T3 card) and a SPA-8XCHT1/E1 (channelized T1 card) will I be able to TDM cross connect the DS0's between the cards? Is there a limit on the number of TDM cross connects? Also, I noticed the CMM cards are EOL. Ideally we'd like to terminate PRI's into the 7606 and run H.323. We'd like to pass voice calls to CUCM and TDM switch FAX calls (via H.323 dial-peer) to a given CAS DS0 on the SPA-2XCT3/DS0. Is this doable with any of the current cards? If not, then we'll stick to the configuration in the first paragraph and only have the 7606 handle the TDM cross connects.
View 3 Replies
View Related
Dec 20, 2012
Can not connect to Cricket wave
View 1 Replies
View Related
Nov 13, 2012
i have 2 routers 2821 with wic-2t serical card and 1921 with hwic-2t serial card.can i connect between those two serials card with serial cross cable ?
View 3 Replies
View Related
Mar 18, 2012
I have c3750 and c4500 switches. I want to cross connect 2 v LAN so I need connection 2 different v LAN s. Can you provide example configurations?
Whatever other case, I want to cross connect between c7200 and c3750 2 different v LAN. It's possible?
View 3 Replies
View Related
Sep 9, 2012
I have reinstalled windows 7 on my laptop. the problem is that the wi-fi internet is not working anymore. The network icon in the system tray shows a cross sign with a red color. I cant seem to be able to find a solution. Tried all the solutions listed in the forum. When i connect the lan cable directly into the laptop the internet works fine. But as soon as i remove it the cross sign again comes and i cant have internet access. I am having an Atheros Ar9285 Wireless Network Adapter installed in my device manager and everything is fine there with no ? or ! marks. I am using a Belkin router with in built modem.
View 1 Replies
View Related
Jan 8, 2013
I am trying to implement in the lab. I have 2 switches 3550 and 3750. my questions are:
1. why i can't see vlans in the running config on switch 3750 even after i created 3 vlans?
2. the 3750 is power over ethernet switch and i am trying to connect 3550 and 3750 thru cross over cable trunk link and the ports doesn't show up no light nothing. is it the right way of cabling.
View 6 Replies
View Related
Oct 20, 2011
Long time since I have had to configure a router and have a small project
Here is what I have in a simple diagram:
PC(static IP)--to--Switch--to--(Ethernet0 int, WIC0)1721 router(FastEthernet0 int, built-in)--to--Switch--to--PC(DHCP)
I need static IP PC to be able to ping the DHCP client. Static IP units 10.1.1.x/16, DHCP clients 10.1.3.x/16.
I have found these overlap and thus give errors and will even shutdown the interface if I enable certain things like routing or bridging.
So I gather I need to change one interface IP range, which would be the DHCP side, I need to stay 10.1.1.x/16 for static side.
View 7 Replies
View Related
Jul 16, 2012
I'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 usb dongle directly into my computer it works perfectly and I got the router to work using a ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port. I get a connection at 40% and 100 bytes are sent and some are received but the connection drops. Is it a problem with the connection? I will upload a image.
View 3 Replies
View Related
Dec 12, 2012
I'm having trouble connecting my 360 to the wireless router to gain Internet access.I use my phone's Wi-Fi to gain internet access with NO issues. My current setup: NetGear Wireless router is connected to my D-Link wired router, and I can access the internet no problem. (10 MBPS down, 5MBPS up)When I try to connect the 360 to the Netgear Wireless router, it connects to the Network, but Internet test it reads "DNS error - The router or modem may mot be automatically providing DNS settings. Try a manual DNS setting instead."(Next suggestion) "DNS Error - If you have a PC that can successfully browse the web, check it's network properties to find the DNS address it uses..."Now, I have XBMC running on my computer, and the 360 can access the network so it shows up under Video Apps so I can see a file list to stream movies. When I try to run a movie, it says I must download an update - so I can't watch the movies at all.I juso set it up so I can access the Network AND Internet.Again, Netgear wireless router (which 360 connects to) connected to D-Link wired router.
View 10 Replies
View Related
May 11, 2012
i have my E1000 network detected by laptop and devices but can't connect to Internet. The E1000 is connected to Cisco 2100 modem and I can connect to Internet if I plug my laptop/PC directly to Cisco 2100 modem.
View 2 Replies
View Related
Sep 17, 2012
Am running Cat6 cable to my cellar. I plan to run a face plate in the walls of all rooms where there will be an ethernet connection. Originally when I did this in a previous house I wired two rooms together i.e. a face plate in one room and the other end a face plate. I did a cross over cable for this so when connecting anything at the other end it would talk to the device in the other room i.e. room A NAS straight through to face plate, room B PS3 straight through to face plate for example.However as I will be connecting multiple rooms together in to a patch panel then switch / router how will this then work? For all rooms where there is face plate do I crossover all cable to the patch panel or straight through? If straight through to the patch are my patch leads then cross overs to the switch?
View 2 Replies
View Related
Aug 11, 2011
I have only one PC. I use cross cable for setup Domain controller. Than network icon show available network but it is just only send and can't received.
View 1 Replies
View Related
Dec 28, 2011
We have cross domain trust relationship established and I have added the user group in our ACS 5.1. we are using Active directory as an external Identity store. Also I have created a rule in the 'Access polices' to allow the user group. From the cross domain, I use abc@xxx.xyz as a user id, but I get this error message 13036 Selected Shell Profile is DenyAccess.
View 3 Replies
View Related
Mar 12, 2012
I have an ASA-5505. [code] I have an Exchange server on the 10.10.10.0 network. I need to be able to allow Active-Sync and OWA from the Guest WiFi through to the Exchange server on the 10.10.10.0 network. The Guest Wi-Fi uses external DNS so traffic is going out to the Internet and getting an IP address which is of course assigned to the Outside interface abd trying to come back in on that interface.How do I make this do what I need? How do I setup the rules to allow this traffic?
View 2 Replies
View Related
Mar 4, 2011
I am having an issue with ,my Dell latitude 600 laptop.When I try to connect WIFI it does nothing...showing red cross on taskbar button...
View 1 Replies
View Related
May 22, 2013
We are configuring a new EMC VNX, and plan to use Ether channel with our 3750x stack. We would like to configure it for both additional bandwidth and for redundancy. What is the best configuration to use? Should we trunk the channel or use switch port mode access, and use channel-group on or protocol LACP (which state active or passive)?
View 1 Replies
View Related
Jan 17, 2013
Is it possible to configure a cross stack etherchannel between 2 SG500 (in stack) and 1 SG200/SG300?
View 13 Replies
View Related
Dec 21, 2011
I have a new 877 that I am using for internet traffic for 3-4 internet only devices.I also have a clean network that i want to insure no cross contamination. However I plan on rolling this out to many sites, but for management I was hoping to set up a reverse telnet to the console port from our one of my clean switches. which should allow me to keep the units seperated and allow me to manage changes etc remotely. Unfortunatly there is no Aux port on the clean switch (3560). Is there still a way to acheive this? can i configure one of the ethernet ports to connect to the console of the 877?
View 2 Replies
View Related
Mar 25, 2013
We have a pair of WS-C3750X-24T-S in a stack and four WS-C2960S-48TS-L in a stack of their own. There is not really anything too fancy configured (no special VLAN configuration/trunks or etc.) but the 3750 do have two ports configured as L3 for routing. We are not trying to use those ports for EtherChannel. These devices are running IOS 12.2(55)SE3 Essentially we are attempting to make an EtherChannel group using port 48 on all four of the 2960's in their stack (four ports). On the 3750 we will configure an EtherChannel group using port 23 and 24 on both switches (four ports). We then connect them up to form a four member EtherChannel.The ports on both ends are configured as mode ON and they are all 1Gb ports. I elected mode on because I understand at least one of the EtherChannel protocols will not work cross stack. What I would like to ask is whether the above configuration is possible or are we hitting some sort of limitation of EtherChannel cross stack, etc..? I cannot find anything to suggest this configration is invalid, but thought I would ask to see if I missed something in the EtherChannel articles.
View 3 Replies
View Related
Oct 23, 2012
I am running out of ports on a 4507R and would like to use a 3750G-24TS stack that I already have to expand capacity. Is it possible to configure EtherChannel between the 4507R and the 3750G stack and if so what is the best way to do it? without LACP, with active-active mode LACP or passive-active mode LACP...
This is what I have in mind:On the 4507R side I would like to use interface GigabitEthernet3/5 and interface GigabitEthernet4/5 where modules 3 and 4 on the 4507R are "6 1000BaseX (GBIC) (WS-X4306-GB)". On the 3750G side I would like to use ports 28 on both switches in the stack which are equipped with Cisco GLC-T= 1000BASE-T SFP transceiver module for Category 5 copper wire with RJ-45 connector. [URL] Cross-Stack EtherChannel Without PAgP or LACP should look like this:
3750switchstackA(config)#interface gigabitethernet 1/0/28
3750switchstackA(config-if)#channel-group 1 mode on
3750switchstackA(config-if)#switchport trunk encapsulation dot1q
3750switchstackA(config-if)#switchport mode trunk
3750switchstackA(config)#interface gigabitethernet 2/0/28
3750switchstackA(config-if)#channel-group 1 mode on
[code]....
is that what I should be doing? is there any benefit to the active-active mode LACP or passive-active mode LACP and which are applicable to the case above?
View 1 Replies
View Related
Jan 28, 2012
According to the following Cisco webpage, cross-stack 10-Gigabit EtherChannel is possible on the 3750 with up to two 10-Gigabit modules, using LACP: url...However, the webpage doesn't confirm if this functionality is restricted to a particular 3750 model, such as 3750E, or if it applies to all models. It also doesn't specify any particular IOS feature set. I've tried Cisco Software Advisor but it doesn't list this feature on either the 3750E or 3750-X. This is possible on the 2960-S switches (i.e. cross-stack 10gig EtherChannel)?
View 23 Replies
View Related
Feb 22, 2012
i want to realize a 20gb ring stp with 6 3750x stacked by 2. I want to install 2 3750x stacked configured in hsrp mode with other 2 3750 stacked. These 2 different stack are interconnected by a cross-stack ether channel 20Gb fiber. On the other side of the room i want to create a new stack with 2 3750x with cross-stack ether channel 20gb connected with the previous 2 stacks. So, in total 3 different cross-stack ether channel 20Gb stacks interconnected creating a ring stp of 20 Gb.
View 4 Replies
View Related
Nov 23, 2012
Namely an Unidentified Network with no NETWORK access. Some information first, the NIC that Im using is the Realtek PCIe Family Controller, Ive updated the drivers, Ive uninstalled, Ive reinstalled. Ive basically been on the internet for the past two days trying all the solutions. Including refreshing and renewing my ip, trying a static ip (although, Im still not sure if I did this step correctly) Ive tried disabling IPV6, Ive tried adjusting my speedflux. The problem is also intermittent with seemingly no reason whatsoever, some days Ill go without internet for the entire day, then the next day Ill boot up my computer and Ill have internet again. It should be noted that when I enable WIRELESS on my laptop, Im able to connect to the network, but when I enable wired, I am not able to.
Here is the ipconfig /all for when Im connected wirelessly and have a connection.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig /all
[Code]....
It should be noted that I am using powerline adapters for my connection, but as I said, this problem only recently started cropping up. I went fine for almost a week with no problems, then all of a sudden it started happening. Im still able to connect wirelessly so its not too much of an issue, but I prefer via Ethernet..
View 2 Replies
View Related
Nov 23, 2012
Recently I've been having some internet problems. Namely an Unidentified Network with no NETWORK access.the NIC that I'm using is the Realtek PCIe Family Controller, I've updated the drivers, I've uninstalled, I've reinstalled. I've basically been on the internet for the past two days trying all the solutions. Including refreshing and renewing my ip, trying a static ip (although, I'm still not sure if I did this step correctly) I've tried disabling IPV6, I've tried adjusting my speedflux, believe me I've tried just about everything, I don't have one blue link left when it comes to my google searches on fixing this problem.The problem is also intermittent with seemingly no reason whatsoever, some days Ill go without internet for the entire day, then the next day I'll boot up my computer and I'll have internet again. It should be noted that when I enable WIRELESS on my laptop, I'm able to connect to the network, but when I enable wired, I am not able to.[code] I'm still able to connect wirelessly so its not too much of an issue, but I prefer via Ethernet.
View 2 Replies
View Related
Mar 3, 2013
configuring EtherChannel between 3750-X cross-stack and 6509E switch. I use two ports on 3750s, and two ports on 6509. I just need it as a trunk. For some elusive reason one port on 3750 keeps being err-disabled, and one on 6509 notconnected.
Here is what I did so far.
3750
!
interface GigabitEthernet1/0/22
description ***VSS-RNOC-link***
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2
[code]....
Problem with :
GigabitEthernet1/0/22 is down, line protocol is down (err-disabled)
GigabitEthernet2/1/29 is down, line protocol is down (notconnect)
I tried shutting them down, then no shutting them again. Didn't work.
View 11 Replies
View Related
Mar 1, 2011
I am becoming very irritated with my laptop. I would like to know why I can only connect to the network Linskeys, and it'll have this little yellow thing, and it'll say its connected but once i click and internet thing (like google chrome) it will say I am not connected.
View 4 Replies
View Related
Apr 19, 2012
my brother wanted me to download some program on my computer, i did so and it needed a reboot, once i rebooted i couldnt connect to the internet anymore. its been like this for about 3 weeks. i would really like to be able to use my computer again. it says its connected to a unidentified network, but cant connect to the internet.
View 13 Replies
View Related
Oct 7, 2012
Is there such a thing as a repeater, or relay which can receive the wireless signal from the router which is situated at one end of the house, and resend it to a part of the house that doesn't get a good signal from the router?
View 1 Replies
View Related
Sep 19, 2011
I have an internet connection of 100.0mbps and have two pc connected to it sharing internet connection but the other pc can't connect to internet when the other one is connected? how can i i fix it?
View 16 Replies
View Related
Oct 29, 2012
I am currently having a problem connecting to the internet on my desktop connection. It is a wired connection from the modem straight to my desktop's ethernet port.It has been fine for a long time until today where it is suddenly unable to connect to anything internet-related at all or takes a long time to load even half of the page.My desktop is running on windows 7 and I was using avast antivirus until i tried uninstalling it in an attempt to fix the issue but to no avail.I am able to use the cmd and ping to other websites but the problem is, all of them have a latency ranging from 500-1000ms, even websites that are local to me.I have tested the connection on my laptop and it seems to work properly without all the problem stated. [code]
View 1 Replies
View Related
Apr 22, 2011
Windows 7 64-bit Home Premium
ACER Aspire X3400
Nvidia Nforce 10/100/1000 ethernet
Cable internet
SB1502 Cable modem
When I try to connect to the internet, it just says "identifying" then says it is an "unidentified network". I've tried:
Resetting the modem
Checked all cables
Uninstalled and reinstalled the drivers
Disabled & enabled the drivers
It's set to automatically connect to DNS
Updating the ethernet with the latest from Microsoft
Ran ipconfig /release and renew
Tried another modem and new cables
Tried other houses with DSL & Cable internet
I installed a USB wireless device which worked when I tested it in wireless areas. But so far nothing has worked for the wired part. At one point before all this started, the internet worked intermittently and would work at other houses perfectly. So I assumed it was my modem or connection at my house. But then I plugged another PC into my modem and it worked instantly. So I know there is no physical problem with my connection, modem or cables.
View 10 Replies
View Related
