I currently own 3 Dlink DWL-3200AP that are setup on MultiSSiD with Vlans 1 and 2. I just picked up 3 Cisco 3550 layer 3 switches. I also own a Cisco ASA 5505 (acting as a router) which is connected to the internet. The 3 switches are connected using the GiBi connectors to each other. They are across the campus from each other, one switch is in the room of the router. Each switch has 1 of the Access points on them.
What I am trying to do is setup the switches to take SSiD 1(Vlan1) to have access for the entire network and have SSiD 2(Vlan2) just hit the router for internet.
I have all static IP's setup on the SSiD 1(Vlan1) connections, and I want to have a DCHP server for the SSid 2(Vlan2).I setup in the Cisco Network Assistant, for the 3550's to have VLAN 1 be port 48 and VLan 2 be port 47 going to the router.
What is currently happening is that if I connect to the SSiD1(Vlan1) I can access all of the switches and the router no problem. When I connect to SSiD2(Vlan2) I cannot connect to anything, ping or otherwise. I figure it might be something in the Access Point but at this point I am hitting my head on a wall trying to figure out what is going on.
i have a dlink-615 router and im wondering if i can configure it the best way possible to work best with wireless devices, like my laptop.there are 4computers running on my network and i want to get the best result possibly for my connection.can i change settings in the routers configuration page so 1 computer can have 90% of the signal or bandwidth of the connection.i want to decrease the other 3family members connectivity to my router, like limit their use of the network or signal/speed/bandwidth strength?
i have internet connection which is connect using dynamic ip address but if i add ip address in Local Area Connection i get two networks, one is internet dynamic ip & other one is ip which i setup in Local area connection. so if i select LAN network for lan clients i can access lan. but now i have DLINK DIR 615 router so what should be my settings?
We are trying to replace the CSS between our firewall and DMZ with a BigIP. Among it's other functions, it will act as the router between the firewall and the DMZ. To make this work, I need to assign vlan tags values for the vlans I create on the BigIP box and these must match the tags on the cisco switches (3550's) How do I find this information on the switch?
I am having trouble after creating a management vlan (99) on a 3550 switch.I have configured the vlan (99) and given it an IP (192.168.1.100) and a default gateway (my router address - 192.168.1.99).I can ping to the switch from a PC and vice versa. The management VLAN IP is fine but now I cannot ping to the router from either the PC or the switch.It seems that just by adding VLAN 99 with it's own IP address has now prevented pings from the switch/ PC to the router ?Due to the fact that I have created a new switch management VLAN with an IP, does this mean I have set up the router as a 'router on a stick' scenario ? [code]
I am attempting to create a mass upgrade server for some of our more standardized equipment since our vender cannot upgrade them pre-shipping for us, we've got to do them on our own. This means using a terribly organized wizard written in what appears to be Java...
I have an aversion to Windows and felt that I could accomplish the same thing using expect scripts and a Gentoo Linux server; now all I need is to set my Cisco 3550 (c3550-ipservicesk9-mz.122-44.SE6.bin) to have each port on it's own VLAN, except for fa0/1 which will be a trunk port to communicate with all ports as well as the server.
I was given a task of creating a vlan and isolating one pc to access an internal website (192.168.90.15) on a specific port (port 8080)The pc is connected in the following manner:
PC--> HP Switch --> Cisco Small Business SG200 switch --> 3550 Catalyst 1, 3550 Catalyst 2 and 3550 Catalyst 3.
I have created a vlan 110 on the Main 3550 Catalyst switch and successfully added the pc to that vlan.However, that PC must be able to access the internet and an internal website on port 8080.I have placed an access-list on the main 3550 catalyst switch which is connected to our router as below:
Client ip address: 192.168.100.2 VLAN 110: 192.168.100.3
access-list 110 permit tcp host 192.168.100.2 host 192.168.90.15 eq 8080access-list 110 permit icmp host 192.168.100.2 anyaccess-list 110 deny ip 192.168.100.0 0.0.0.255 ? I was unable to access the webserver even after many attempts.
I'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
I have enabled ip routing But I dont have a default route, this is becase we don't have a router on the network.
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655 Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50 10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50 10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
I have set up 2 DHCP pools and 2 VLANs (1 *the native* for data / 1 VLAN for voice). When I use the command "switchport voice vlan 20" the port disapear from the show vlan brief list. When I use the "switchport access vlan 20" it shows up in the show vlan brief in the correct VLAN and gives the phone an IP. I assume that using the access instead of the voice is wrong and the phones would not configure correctly. But when I use the access the phone goes to the next step and tells me the TFTP files are not found. Why does the port disapear from the VLAN list?
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20. At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
I'm wanting to setup a Virtual Office scenario. Everything is working fine except for 802.1x...I can get the 881 to authenticate things connected to it, but I don't have the options of guest-vlan or auth-fail vlan.Idea is if the users takes the router home and someone, either accidentally or on pupose, connects an unauthorized Laptop, they stay off the Corp network but can get to the internet still.I found this link on Cisco's site: [URL]That link shows them configuring a guest vlan right on the fa0-3 ports of an 881W. I dont have that option on mine. I can only configure 802.1x on the vlan interface. I have 802.1x working, for things that connect to vlan1, but I would like to have a "fallback" setup.
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
I am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
I've been given the task to clean-up our network config, and have walked into a disaster zone.We have a 4510R on site with everyone using the default VLAN, VLAN 1.I have created 4 new VLANS, VLAN100, VLAN150, VLAN200, VLAN250 I have assigned interface addresses to each VLAN and configured Inter VLAN routing.I can route to and from each new vlan with no problem, i.e VLAN250>VLAN100 VlAN100>VLAN200 etc but I can't route to VLAN 1(Default VLAN) from any of them, I can ping the interface on VLAN 1 from any VLAN , but any hosts are unreachable. On the flip side , from VLAN 1 I can route to all of the VLANS.
I have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
Where would I find instrutions on how to import CA certified identity SSL wildcard certficate ( like *.company.net - ) in ASA?,The CSR for the wildcard certificate was not generated out of the ASA unit.
I have a Catalyst 3550 switch and 2610XM router connected with an ethernet cable. Currently I cannot get the port on the switch to open (lights are dark.) I run 'no shut' on the port (#13) but nothing happens. If I unplug the cable to the cisco router and plug in a Netgear router (that leads to the internet) into the same port, the port flickers amber for a while, then flickers green from then on.) I switched the cables, both work fine when connected between the switch and the Netgear router.
This was working at one point a couple of days ago. I had the Netgear router plugged into another port on the switch and could ping from the cisco router through the switch to the Netgear router. I thought I had figured things out, but a reboot disavailed me of that notion. (I know, I guess I didn't save my configuration, but I obviously still need to understand more, so its better that I didn't.) (I guess.)
When the problem is occuring, the below is what I am seeing on the two devices.
ROUTER status ==================================== FastEthernet0/0 is up, line protocol is up Hardware is AmdFE, address is 0017.9583.b740 (bia 0017.9583.b740) Internet address is 192.168.1.90/24(code)
