Cisco Application :: How To Enable Snmp On Css 11501
Feb 13, 2012i need to enable snmp on Cisco CSS 11501.
View 1 Replies
ADVERTISEMENT
Cisco Application :: Clear Stickies On CSS 11501 By VIP?
Jan 30, 2012it's possible to clear stickies per VIP? The firmware is 08.20
View 2 Replies View RelatedCisco Application :: Slow Download Via SSL In CSS 11501
Nov 27, 2011I have 2 CSS 11501 providing load-balancing rules and SSL termination. When CSS is used for downloading through the rules of SSL, the rates I get are quite lower than those obtained when the download is done either directly on the machine or by using the rules of HTTP. Is it normal? Is there anything that canspeed up this process?
View 2 Replies View RelatedCisco Application :: SSO (Single Sign-on) Through CSS 11501?
Nov 22, 2011I am load balancing Terminal Server Windows 2008 sessions with an CSS 11501. The code version is sg0750004 (07.50.0.04). I am trying to establish a Terminal Server session with Single Sign-On (SSO), but without success. Normal login with Username and Password on the TS are functionning, but never SSO session. The environment is: 10 Windows 2008 Terminal Servers (NTS1, NTS2,NTS3...). In DNS I have a host A named TS with IP for balanced CSS. The problem I see is that the client PC opens a TS session to "TS". then dont work SSO, but if client PC open a TS session to NTS1, NTS2...is working fine the SSO I am not sur if we can do something on the CSS.
View 3 Replies View RelatedCisco Application :: How To Test CSS 11501 Failover
Aug 7, 2012I have 2 CSS, 1 as primary and 2nd as standby. I configured the standby CSS as my old standby CSS box and now wanted to test the faliover. I am not aware of how to test it in. ny how i have cr for that.
View 1 Replies View RelatedCisco Application :: CSS 11501 Not Dropping Flows If Service Is Down
Oct 14, 2012some misconfiguration (?) may be the reason for an undesired behaviour we are experiencing with our Cisco CSS 11501s. Balancing mechanisms work fine, however if a service transitions to the "down" state, the corresponding flows remain "alive" leading to a temporary outage of our service. Subsequent client requests are still being sent to the "down" frontend which is unresponsive.
View 4 Replies View RelatedCisco Application :: CSS 11501 Load Balancing With X-forwarded For Address
Sep 15, 2011We have a pair of CSS 11501,Currently it is using source ip for load balancing and 5 servers as backend , however we have users loggin in using http and based on its source IP (ISP PROXY) , it is forwarded to SERVER A.However, we have a SSL page and when the client switches over to SSL , it is forwarded to SERVER B/C/D/E based on its source IP ( REAL CLIENT IP) .This will cause the user to be terminated as the 5 servers are independent and not running in a cluster.
Is there any way that we can use the X-Forwarded-For address to load balance so that when users loging , they are sent to SERVER A (Based on X-Forwarded-For Header IP which translate to REAL CLIENT IP).This way we are able to also send it back to the same server when it uses SSL.I believe that we should be able to load balance using X-Forwarded-For IP or to rewrite the X-Forwarded-For IP into client source IP.
Cisco Application :: Active CSS 11501 Telnet And Console Not Working?
Mar 31, 2013implementation of the cisco CSS 11501 boxes available as spare on our site into production for an application evry thing worked as expected. i was able to telnet the active/master box and was able to console both master and backup box from the console port.however a week post the activity im faced with this weird problem where im not able to take console or the telnet access of my primary/active box.The boxes are working in BOX-to-BOX redundancy and now im not able to telnet or console my active/master box. The telnet and console window prompts me for username and password and after entering the credentials nothing happens. no prompt or no error message is displayed.
The telnet primary authentication is via tacacs and secondary is via local. however for console im not using any method for primay authentication and local for secondary authentication. however i can successfully console my backup box. below are my obsrvations 1. the left and right status LED on the active CSS box is OFF.- it means my CSS 11501 failed and has no power. 2. upon firing the rcmd command with show line command on backup box i see that the telnet sessions and console session is established with the master box3. the redundancy state of the active box says it is master and has not changed state since my last activity, no application issue reported, all the services are active on the active box and also i can ping the active box ip address from my backup box over which box to box redundancy is established. This confirms the active box is functioning well 4. i initially thought the telnet sessions are not getting cleared, however the show line cmd with the rcmd cmd on the backup box confirms this is not happening. now im stuck as the active box cannot be accessed at all via console or telnet. i was thinking of below steps to be carried out.1. to failover the boxes and make the backup as master2. then try to take the faulty box off the network and troubleshoot (are there any other commands that i should use to troubleshoot)3. if nothing works try rebooting the box and check
NOTE: the software running is version 7.20.30.3 with standard feature set. we are not using cvdm or the CSS GUI. we could access the css initially on CSS gui and that is also not working now.
Cisco Application :: 11501 Ftp Server Setup Using Non-standard Port?
Dec 13, 2011we would like to setup FTP server over CSS where our member sever use non-std-port to open both control/data channel (i.e. 6370 as ctrl and 6369 as data this case.) but seems we only get Passive mode FTP mode work only but not for Active mode FTP case for data channel establishement for server back to client..
# sh ver
Version: sg0820501 (08.20.5.01)
Flash (Locked): 08.10.1.06
Flash (Operational): 08.20.5.01
Type: PRIMARY
Licensed Cmd Set(s): Standard Feature Set
[code]....
Cisco Application :: CSS 11501 - Wildcard Certificate With Subject Alternative Names
Sep 6, 2012I generated a wildcard certificate for my company type *. [URL] in a CSS 11501. For the site [URL] worked fine, for the site [URL] didn't worked. I read on the web that should generate a wildcard certificate with subject alternative names. Is it possible in CSS? how can I do it?
View 5 Replies View RelatedCisco Application Networking :: CSS 11501 Reboots When Making Change To Global Keepalive?
May 17, 2010I've got an issue with a CSS 11501 where, if *any* change is made to a global keepalive (active), the device reboots. The code is 08.10.2.05. I'm unable to search the TAC archive or I would've gone there first.
View 2 Replies View RelatedCisco Application :: Content Switch 11501 / 11503 Abnormal Interface Link Down?
Mar 27, 2013I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies View RelatedCisco Application :: Sample Command Output Of Show Chassis Inventory For CSS 11501 / 11503 / 11506?
Oct 30, 2011I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
Cisco :: 871 - How To Use Telnet To Enable SNMP In Router
Apr 6, 2012Is it possible to enable the snmp in a router via telnet with the wan address(I have the routers' passwords) ? If yes, how
Router 1 : Cisco 871 w
Router 2 : Sagem – F@st 3304 v2
How To Enable Snmp On SVI Interface On Cisco ME-3600X-24FS-M
Sep 14, 2011how to enable snmp on SVI interface on cisco ME-3600X-24FS-M?I can't see traffic on SVI via snmp.
View 13 Replies View RelatedCisco :: Enable SNMP Traps On Nexus 1000V?
Dec 18, 2011I want to configure snmp-traps regarding stpx (root-inconsistency, loop-inconsistency) on a Cisco Nexus 1000V. The command "show snmp traps" lists stpx as a trap that could be configured and which is not at the moment.
MKBE1NX1# sh snmp trap
--------------------------------------------------------------------------------
Trap type Enabled
--------------------------------------------------------------------------------
entity : entity_mib_change Yes
entity : entity_module_status_change Yes
entity : entity_power_status_change Yes
[code].....
Nothing about stpx... Is there some other way to configure more traps?
Cisco :: 2800 Enable SNMP Discovery Through External Interface
May 28, 2012I'm trying to add some 2800 series routers to our monitoring environment, but I can't get them discovered.
On the Mgmt Server I need to go through a "discovery" process to add the 2800 to the system. For this I target the internal interface ( i) but the discovery fails. I'm assuming the packets are getting dropped on the outside interface (e). I know SNMP is set up correctly and works as I had PRTG installed on a local box (p) for testing purposes.
The intention is to do the data gathering via a proxy agent (p), so enableing SNMP on the outside interface is not going to do me any good.What do I need to do to let those discovery packets pass through? At least temporarily?
Cisco Switching/Routing :: 3750 - Enable SNMP On Switches?
Dec 26, 2011I want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
Cisco Firewall :: ASA 5510 - Enable SNMP For Bandwidth Monitoring Using PRTG?
May 1, 2012I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies View RelatedCisco Switching/Routing :: 2960 - Enable Snmp For Switch Port
Dec 18, 2011i want use CACTI for monitor my bandwidth so i have a question how can i enable snmp for a switch port ? or i shoudl just enable snmp from configuratiopn terminal and then in CACTI i will choose which port will be monitor? can i do something that CACTI connect to my switch with a encryption key ? i have cisco 2960 48 port switch
View 2 Replies View RelatedCisco Application :: SNMP Setup On GSS-4492-k9?
May 22, 2012configured my GSS to setup traps to snmp server ,but the snmp server is not receiving any traps from GSS
snmp-server enable
snmp-server community-string public ro
snmp-server host 10.19.41.11 public traps version 2 udp-port 162
[Code]......
Cisco Application :: How SNMP EngineID Derived On ACE30
Nov 9, 2011We currently have 6 admin context and they are all utilizing the same snmp engineid (Local SNMP engineID: 800000090441646D696E) which is causing issues as far as our monitoring/performance platform CA eHealth. Isn't the engineID, by default, the first interface on the device?
Doesn't seem to be the case on an ACE30.How is the SNMP engineID derived on the ACE30?
Cisco Application :: SNMP Server Not Receiving Traps From ACE 4710
May 24, 2012Had setup my ACE ,to send traps to SNMP server .but dont see any logs on the SNMP server from ACE.
SNMP configuration on ACE
logging enable
logging buffered 6
logging host 10.12.40.12 udp/514
[code].....
Cisco Application :: ACE 4710 Switchover SNMP Trap Notification?
Jun 20, 2012I am in the process of testing VA5(1.2) version of ACE on ACE4710 appliance.I did redundnacy configuration and it is working fine.I have done the snmp configuration and SNMP trap receiver is able to recieve traps like link up/down, so it proves that SNMP configuration is working fine, but i am not able to generate the SNMP trap notification for "clrRedundancyStateChange".I tried two things:
1) Via CLI, ran the command "ft switchover all" and i could see redundancy state changes.
2) Powered down Active 4710 appliance and standby ACE 4710 appliance taking over as Active.
However, none of the above could generate the trap clrRedundancyStateChange. how this trap can be generated? In snmp-server enable traps commands doesn't have any option for enabling FT related traps.
Cisco Application :: How To Monitor Status Of Vips On 11503 Through SNMP
Sep 26, 2011what is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 2950 - Release For Snmp-server Enable Traps Errdisable Command?
May 16, 2013We have a catalyst 2950 switch running:
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
This release doesnt have the snmp-server enable traps errdisable command.
Where to look on the cisco site for the next available release for me that would have this command in place?
Cisco Application :: Possible To Modify Configure With Snmp On Ace Module Like Others 6500 Catalyst
Apr 12, 2012Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View RelatedCisco Application Networking :: ACE 4710 SNMP False Linkup / Down Trap Notification?
Feb 6, 2013We have two ACE4710 in a failover configuration with Software version A4(2.0). SNMP is setup and the receiver is able to receive SNMP traps.The issue is we are receiving a linkDown trap notification at least once every other day, followed shortly by a linkUp notification a minute later. We have checked all layer 2 devices connected to the ACE and cannot see any evidence that any link actually disconnected. We experienced no traffic lost, but this could be because a couple of the ACE links are bundled. The trap notification does not actually indicate which interface changed status. All links are Gigabits, and there are no packet drops either on the ACE or the layer 2 switch.
View 3 Replies View RelatedCisco Application :: To Enable SSL3 On Content Switch
May 23, 2011I had meeting with security auditor for a customer, he told me that i need to enable SSL3 on content switch as his scanning found that all network is working on SSL2.I could not understand his view and then when i found the content switch documentation, it is mentioned that SSL3 is default enable on content switch."By default, the SSL version is SSL version 3 and TLS version 1. The SSL module sends a ClientHello that has an SSL version 3 header with the ClientHello message set to TLS version 1." Do i have to do some kind of configuration to enable SSL3 or its enable by default ?
View 3 Replies View RelatedCisco Application :: 3500 - Enable XML-HTTPS Protocol In ACE
Mar 9, 2011I'm configuring ACE to enable the XML-HTTPS interface so I can import it into ANM, when I try to do a "match protocol xml-https any", I get a invalid command detected. When I tab at the match protocol command, I don't see xml-https listed (http, https, icmp, etc. is listed).
View 2 Replies View RelatedCisco WAN :: Upgrading CSS 11501 Firmware
Jun 12, 2012We are about to upgrade Cisco Load Balancer CSS 11501 firmware from current ver, 8.10.4.01 to 8.10.6.02,this is a production line device (a running 24x7 network), upgrading will create unpredictable results even worst the network will go down.
View 1 Replies View RelatedCisco WAN :: 11501 CSS Load / Advance Balancing
Mar 1, 2011We have Cisco CSS 11501 and connected in One-Arm way.Currently there are 4 source sending traffic and 3 server to receive the request. We are using Advance-balancing with Source IP. So the ratio become 2:1:1 or 1:2:1 or 1:1:2.But our target is to do the load balancing in equal ratio.
View 1 Replies View RelatedCisco Switching / Routing :: CSS 11501 - Contact Content VIP On Same Subnet
Feb 5, 2013I have an issue with the device in subject. I need that some server, listed as service on CSS, can contact a content VIP on the same subnet. To allow that traffic I configured grouping on CSS (group 1) with vip address and an ACL that allow traffic from subnet 10.1.1.0/24 toward same subnet 10.1.1.0/24 and I have bound this ACL with sourcegroup 1. The nat and portmap works but never at first attempt, instead since second attempts it works. Seem like a CSS require to much time to create nat entry.
View 4 Replies View Related