We are about to upgrade Cisco Load Balancer CSS 11501 firmware from current ver, 8.10.4.01 to 8.10.6.02,this is a production line device (a running 24x7 network), upgrading will create unpredictable results even worst the network will go down.
View 1 RepliesI'm about to upgrade my asa to version 8 from 7. I see a lot of instructions on using tftp to accomplish this. I also see in the GUI where i can upload the image files for version 8. is there any disadvantage from using the GUI instead of a tftp server?
View 1 Replies View RelatedI have just received a Cisco SF 200E-24P switch and need to upgrade the firmware. The current version is 1.0.0.12 an need to load the latest (or at least 1.1) to get CDP etc. However when I use the upgrade option in the switch I get an error of.Firmware Image download through HTTP failed. Wrong File Type.I have tried 3 different versions of the firmware and get the same error message each time.
View 4 Replies View RelatedI've got a used WS-SVC-FWM-1-K9 on the way and I'd like to standardize it to the Firewall Module Software Version 4.0. I'm not positive if the current software on it is newer or older than Version 4.0. Is this possible to perform or is the Software as is on these modules?
View 2 Replies View RelatedI had a strange problem here after upgrading Cisco 3750X.The upgrading was going smoothly, I copied a newer IOS to the flash from another Cisco 3750X through TFTP, changed the boot image.It took a while do to the microcode upgrading, finally, it started to boot up. But when it completes the boot up, I can't see the normal login prompt, but only some strange codes. From what I can see, it seems some decoding problem, as if I plug or unplug a cable from the switch, the strange code pops up again, like in normal situation, the console tells you that the interface is going up and down.
The original image of the switch: c3750e-universalk9-mz.122-53.SE2.bin
Upgrade to image: c3750e-universalk9-mz.122-55.SE3.bin
However, I don't have any problem to telnet to this switch, as it has correct IP address and login configured before the upgrading. I have reboot the switch for couple of times, reconnect to the serial port still doesn't show me anything.I am wonering has any one has met this situation before? detailed message shown after the boot up. cisco WS-C3750X-48 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1449Z04L
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
52 Gigabit Ethernet interfaces
[Code] .....
I've just attempted to uprade the firmware on my WAG325N from 1.0.6 to 1.0.12 the latest, over wireless. It will not work with Ethernet. It started to upgrade and failed with a garbled screen in my browser. No message to reset. Tried a complete reset several times. Pressing reset, power off for 30 secs. When I attempt to connect wirelessly with browser, just get a garbled screen, with no menus.
View 1 Replies View RelatedI'm trying to upgrade the firmware on my BEFSR81 v3 cable router (firmware version 2.45.xxx) on a Mac. I accessed the interface via Safari browser, followed the instructions, got a message saying not to interrupt the process, but it never completed. So I tried it again (downloaded another copy of the firmware update), and same thing. No choice but to interrupt it. My internet connection seems to be working fine, but now I can't access the router via the browser. I don't think the firmware actually updated.
Should I power down the router and then reset it?
I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies View RelatedWe have a centralized Cisco 5508 WLC with 84 APs(1142N) in branches (slow WAN links), Current WLC IOS version is 7.0.220.0.Recently we bought new Aps Air CAP36021-N. These APs are not compatible with existing WLC IOS. If I upgrade WLC, then can I stop propagating newer firmware for old Aps? Because it kills all WAN.
View 9 Replies View RelatedI'm attempting to upgrade to firmware 5.00.38 for my WRT54G-TM router, but it keeps telling me "upgrade failed" after like 3-4 seconds of trying. It says I currently have firmware: DD-WRT v24-sp2 (06/13/09) mega - build 12288. I've tried restetting to factory defaults before upgrading, but doesn't work.
View 1 Replies View RelatedCannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios. They connect ok using Belkin and Linksys routers.
View 4 Replies View RelatedI have a little problem with my new E1200. Before the E1200 I had a WRT160N that was bricked to death by a power surge due upgrading the firmware. Till that moment the WRT160N met al the required specs as told in the description..I have from my ISP a 40Mbit cable line and was always downloading at those speeds wired aswell as wireless...
Now with the E1200 I get the 40Mbit only wired... wireless it only allows it up to max. 20Mbit.I figured that I didn't do anything different than the Linksys I had before..I'm working with a MacBook from late 2007 running OSX Lion 10.7.2, Built-in AirPort Extreme card (802.11a/b/g/n)My wireless setting with a WP2 Personal Security Mode
Region : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1.URL
I've got a mixed stack as follows:
Switch 1 - 3750X-24P
Switch 2 - 3750G-24TS
Switch 3 - 3750G-24T
Running 12.2(53)SE2, IP base. Now I tried upgrading the firmware on the entire stack to 12.2(55)SE4 and ran into this error:(Command: archive download-sw /imageonly /overwrite /allow-feature-upgrade tftp://10.20.20.13/c3750e-universalk9-tar.122-55.SE4.tar)
Error: The image in the archive which would to used to upgade system number 2 does not support that system type.I haven't as yet removed the "3750G-24TS" switch from the stack and re-tried as yet, however, is the expectation that without the 24TS, the upgrade should work?
After unsuccess firmware upgrade, my router is leds always light.How I can recover it?
View 3 Replies View RelatedI was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies View RelatedVideo streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?
View 3 Replies View RelatedI just upgraded to a E3000 from a WRT54G and I am having some issues with network speed.I have no special settings and have even tried restoring factory defaults and upgrading to the latest firmware to no avail.The time I notice the biggest hit is when transferring files locally on the network (WiFi and LAN).Let me note that I do know the difference between MB/s & Mb/s and the like.I have Comcast 20Mb/s Down, 1.5Mb/s Up (just a FYI, the main issue is local transfers)
With default settings my Laptop (ASUS N82JQ, Atheros AR9285 Wireless Network Adapter), connects to the router at only 65Mb/s (with full signal).Upload seems to be more decent ~600KB/s (Transferring files from wireless n laptop to the gigabit desktop).Download seems to be limited to ~150KB/s (Copying files from the wired gigabit desktop to the wireless n laptop).These speeds are horrible! ~5hrs to transfer 3GB of data!
One of my laptops had a card that was capable of both 2.4 & 5Ghz and I was previously getting ~2000-5000KB/s (2-5MB/s) transfers with this router (But I had to do a system restore on it and reset the router). My ASUS laptop seems to only work with 2.4Ghz though. If I change the 2.4Gh Wireless settings on the router to "Auto(20MHz or 40MHz)" the laptop will connect at 150Mb/s, but the speeds are the same slow speeds as above.
We have Cisco CSS 11501 and connected in One-Arm way.Currently there are 4 source sending traffic and 3 server to receive the request. We are using Advance-balancing with Source IP. So the ratio become 2:1:1 or 1:2:1 or 1:1:2.But our target is to do the load balancing in equal ratio.
View 1 Replies View Relatedit's possible to clear stickies per VIP? The firmware is 08.20
View 2 Replies View RelatedI have 2 CSS 11501 providing load-balancing rules and SSL termination. When CSS is used for downloading through the rules of SSL, the rates I get are quite lower than those obtained when the download is done either directly on the machine or by using the rules of HTTP. Is it normal? Is there anything that canspeed up this process?
View 2 Replies View Relatedi need to enable snmp on Cisco CSS 11501.
View 1 Replies View RelatedI am load balancing Terminal Server Windows 2008 sessions with an CSS 11501. The code version is sg0750004 (07.50.0.04). I am trying to establish a Terminal Server session with Single Sign-On (SSO), but without success. Normal login with Username and Password on the TS are functionning, but never SSO session. The environment is: 10 Windows 2008 Terminal Servers (NTS1, NTS2,NTS3...). In DNS I have a host A named TS with IP for balanced CSS. The problem I see is that the client PC opens a TS session to "TS". then dont work SSO, but if client PC open a TS session to NTS1, NTS2...is working fine the SSO I am not sur if we can do something on the CSS.
View 3 Replies View RelatedI have 2 CSS, 1 as primary and 2nd as standby. I configured the standby CSS as my old standby CSS box and now wanted to test the faliover. I am not aware of how to test it in. ny how i have cr for that.
View 1 Replies View Relatedsome misconfiguration (?) may be the reason for an undesired behaviour we are experiencing with our Cisco CSS 11501s. Balancing mechanisms work fine, however if a service transitions to the "down" state, the corresponding flows remain "alive" leading to a temporary outage of our service. Subsequent client requests are still being sent to the "down" frontend which is unresponsive.
View 4 Replies View RelatedWe have a pair of CSS 11501,Currently it is using source ip for load balancing and 5 servers as backend , however we have users loggin in using http and based on its source IP (ISP PROXY) , it is forwarded to SERVER A.However, we have a SSL page and when the client switches over to SSL , it is forwarded to SERVER B/C/D/E based on its source IP ( REAL CLIENT IP) .This will cause the user to be terminated as the 5 servers are independent and not running in a cluster.
Is there any way that we can use the X-Forwarded-For address to load balance so that when users loging , they are sent to SERVER A (Based on X-Forwarded-For Header IP which translate to REAL CLIENT IP).This way we are able to also send it back to the same server when it uses SSL.I believe that we should be able to load balance using X-Forwarded-For IP or to rewrite the X-Forwarded-For IP into client source IP.
implementation of the cisco CSS 11501 boxes available as spare on our site into production for an application evry thing worked as expected. i was able to telnet the active/master box and was able to console both master and backup box from the console port.however a week post the activity im faced with this weird problem where im not able to take console or the telnet access of my primary/active box.The boxes are working in BOX-to-BOX redundancy and now im not able to telnet or console my active/master box. The telnet and console window prompts me for username and password and after entering the credentials nothing happens. no prompt or no error message is displayed.
The telnet primary authentication is via tacacs and secondary is via local. however for console im not using any method for primay authentication and local for secondary authentication. however i can successfully console my backup box. below are my obsrvations 1. the left and right status LED on the active CSS box is OFF.- it means my CSS 11501 failed and has no power. 2. upon firing the rcmd command with show line command on backup box i see that the telnet sessions and console session is established with the master box3. the redundancy state of the active box says it is master and has not changed state since my last activity, no application issue reported, all the services are active on the active box and also i can ping the active box ip address from my backup box over which box to box redundancy is established. This confirms the active box is functioning well 4. i initially thought the telnet sessions are not getting cleared, however the show line cmd with the rcmd cmd on the backup box confirms this is not happening. now im stuck as the active box cannot be accessed at all via console or telnet. i was thinking of below steps to be carried out.1. to failover the boxes and make the backup as master2. then try to take the faulty box off the network and troubleshoot (are there any other commands that i should use to troubleshoot)3. if nothing works try rebooting the box and check
NOTE: the software running is version 7.20.30.3 with standard feature set. we are not using cvdm or the CSS GUI. we could access the css initially on CSS gui and that is also not working now.
I have an issue with the device in subject. I need that some server, listed as service on CSS, can contact a content VIP on the same subnet. To allow that traffic I configured grouping on CSS (group 1) with vip address and an ACL that allow traffic from subnet 10.1.1.0/24 toward same subnet 10.1.1.0/24 and I have bound this ACL with sourcegroup 1. The nat and portmap works but never at first attempt, instead since second attempts it works. Seem like a CSS require to much time to create nat entry.
View 4 Replies View Relatedwe would like to setup FTP server over CSS where our member sever use non-std-port to open both control/data channel (i.e. 6370 as ctrl and 6369 as data this case.) but seems we only get Passive mode FTP mode work only but not for Active mode FTP case for data channel establishement for server back to client..
# sh ver
Version: sg0820501 (08.20.5.01)
Flash (Locked): 08.10.1.06
Flash (Operational): 08.20.5.01
Type: PRIMARY
Licensed Cmd Set(s): Standard Feature Set
[code]....
My environment have two device ,a cisco css11501 and a cisco 2960 ,when I reboot CSS11501 then 2960 shutdown fa0/41
I command "sh logging | in 0/41" just up down two time,not five times in 10 seconds
.May 17 11:13:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to down
.May 17 11:13:19: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to down
.May 17 11:14:53: %PM-4-ERR_DISABLE: link-flap error detected on Fa0/41, putting Fa0/41 in err-disable state
.May 17 13:44:35: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to up
.May 17 13:44:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to up
I would like configure a CSS content, that uses the sorry service principal in an advanced way.
I am familiar with the primary Sorry Server command and see that the CSS would send all connections to the named service that is configured as the primary Sorry Server.
What I would like to do is to configure the CSS, so that once it’s decided it’s in a “sorry” state (all the services that are configured with “add service” are down) that it load balances to a different set of services.
To explain what I’ve been trying to do in the form of configuration on the CSS, I’ve pasted some pretend config below.
Connections come into IP address 1.1.1.1, which normally get load balanced between 9.1.1.1, 9.1.1.2 and 9.1.1.3.
If 9.1.1.1, 9.1.1.2 and 9.1.1.3 are all down, the sorry service is used and the CSS starts passing traffic to 1.1.2.1, which I want it to load balance between 9.1.2.1, 9.1.2.2 and 9.1.2.3.
The order that I have applied the config, is different to the below, as I set out to configure in this order: secondary services, secondary content, sorry service, primary services, primary content.
The order of the config below is different, because I wanted it in the order that the traffic flows and the CSS won’t take the config in that order!
The wall I have ran into, is that when I try to create the service I have named “Sorry Service”, I get the following error:
%% Service IP Address conflicts with a local I/F, VIP, mg mt route.
[Code] .....
I generated a wildcard certificate for my company type *. [URL] in a CSS 11501. For the site [URL] worked fine, for the site [URL] didn't worked. I read on the web that should generate a wildcard certificate with subject alternative names. Is it possible in CSS? how can I do it?
View 5 Replies View RelatedI've got an issue with a CSS 11501 where, if *any* change is made to a global keepalive (active), the device reboots. The code is 08.10.2.05. I'm unable to search the TAC archive or I would've gone there first.
View 2 Replies View Related