Cisco Application :: SSO (Single Sign-on) Through CSS 11501?
Nov 22, 2011
I am load balancing Terminal Server Windows 2008 sessions with an CSS 11501. The code version is sg0750004 (07.50.0.04). I am trying to establish a Terminal Server session with Single Sign-On (SSO), but without success. Normal login with Username and Password on the TS are functionning, but never SSO session. The environment is: 10 Windows 2008 Terminal Servers (NTS1, NTS2,NTS3...). In DNS I have a host A named TS with IP for balanced CSS. The problem I see is that the client PC opens a TS session to "TS". then dont work SSO, but if client PC open a TS session to NTS1, NTS2...is working fine the SSO I am not sur if we can do something on the CSS.
View 3 Replies
ADVERTISEMENT
Oct 15, 2012
I haven't run into this before and I can't find anything in the documentation regarding it. (Our 2 4710 were setup prior in a routed configuration although I personally see no reason for it.) Regardless, we have 2 servers that host 4 websites on them. We built everything on the ACE with a new VIP and matching the http header. If we use firefox/chrome, it load balances properly and we are prompted for credentials as those browsers don't support single sign on. We enter our credentials and are able to get to the appropriate website on the server. When we use IE, it fails to open the page. A sniffer capture shows an authentication failure packet and a reset and that's it. We built the ACE both as sticky and non-sticky but neither worked properly with IE.
Is there something else in the ACE we need to configure to get SSO to work?
**NEW CONFIGURATION**
probe icmp PING
description ICMP echo request probe
[Code].....
View 10 Replies
View Related
Jan 30, 2012
it's possible to clear stickies per VIP? The firmware is 08.20
View 2 Replies
View Related
Nov 27, 2011
I have 2 CSS 11501 providing load-balancing rules and SSL termination. When CSS is used for downloading through the rules of SSL, the rates I get are quite lower than those obtained when the download is done either directly on the machine or by using the rules of HTTP. Is it normal? Is there anything that canspeed up this process?
View 2 Replies
View Related
Feb 13, 2012
i need to enable snmp on Cisco CSS 11501.
View 1 Replies
View Related
Aug 7, 2012
I have 2 CSS, 1 as primary and 2nd as standby. I configured the standby CSS as my old standby CSS box and now wanted to test the faliover. I am not aware of how to test it in. ny how i have cr for that.
View 1 Replies
View Related
Oct 14, 2012
some misconfiguration (?) may be the reason for an undesired behaviour we are experiencing with our Cisco CSS 11501s. Balancing mechanisms work fine, however if a service transitions to the "down" state, the corresponding flows remain "alive" leading to a temporary outage of our service. Subsequent client requests are still being sent to the "down" frontend which is unresponsive.
View 4 Replies
View Related
Sep 15, 2011
We have a pair of CSS 11501,Currently it is using source ip for load balancing and 5 servers as backend , however we have users loggin in using http and based on its source IP (ISP PROXY) , it is forwarded to SERVER A.However, we have a SSL page and when the client switches over to SSL , it is forwarded to SERVER B/C/D/E based on its source IP ( REAL CLIENT IP) .This will cause the user to be terminated as the 5 servers are independent and not running in a cluster.
Is there any way that we can use the X-Forwarded-For address to load balance so that when users loging , they are sent to SERVER A (Based on X-Forwarded-For Header IP which translate to REAL CLIENT IP).This way we are able to also send it back to the same server when it uses SSL.I believe that we should be able to load balance using X-Forwarded-For IP or to rewrite the X-Forwarded-For IP into client source IP.
View 3 Replies
View Related
Mar 31, 2013
implementation of the cisco CSS 11501 boxes available as spare on our site into production for an application evry thing worked as expected. i was able to telnet the active/master box and was able to console both master and backup box from the console port.however a week post the activity im faced with this weird problem where im not able to take console or the telnet access of my primary/active box.The boxes are working in BOX-to-BOX redundancy and now im not able to telnet or console my active/master box. The telnet and console window prompts me for username and password and after entering the credentials nothing happens. no prompt or no error message is displayed.
The telnet primary authentication is via tacacs and secondary is via local. however for console im not using any method for primay authentication and local for secondary authentication. however i can successfully console my backup box. below are my obsrvations 1. the left and right status LED on the active CSS box is OFF.- it means my CSS 11501 failed and has no power. 2. upon firing the rcmd command with show line command on backup box i see that the telnet sessions and console session is established with the master box3. the redundancy state of the active box says it is master and has not changed state since my last activity, no application issue reported, all the services are active on the active box and also i can ping the active box ip address from my backup box over which box to box redundancy is established. This confirms the active box is functioning well 4. i initially thought the telnet sessions are not getting cleared, however the show line cmd with the rcmd cmd on the backup box confirms this is not happening. now im stuck as the active box cannot be accessed at all via console or telnet. i was thinking of below steps to be carried out.1. to failover the boxes and make the backup as master2. then try to take the faulty box off the network and troubleshoot (are there any other commands that i should use to troubleshoot)3. if nothing works try rebooting the box and check
NOTE: the software running is version 7.20.30.3 with standard feature set. we are not using cvdm or the CSS GUI. we could access the css initially on CSS gui and that is also not working now.
View 1 Replies
View Related
Dec 13, 2011
we would like to setup FTP server over CSS where our member sever use non-std-port to open both control/data channel (i.e. 6370 as ctrl and 6369 as data this case.) but seems we only get Passive mode FTP mode work only but not for Active mode FTP case for data channel establishement for server back to client..
# sh ver
Version: sg0820501 (08.20.5.01)
Flash (Locked): 08.10.1.06
Flash (Operational): 08.20.5.01
Type: PRIMARY
Licensed Cmd Set(s): Standard Feature Set
[code]....
View 3 Replies
View Related
Sep 6, 2012
I generated a wildcard certificate for my company type *. [URL] in a CSS 11501. For the site [URL] worked fine, for the site [URL] didn't worked. I read on the web that should generate a wildcard certificate with subject alternative names. Is it possible in CSS? how can I do it?
View 5 Replies
View Related
May 17, 2010
I've got an issue with a CSS 11501 where, if *any* change is made to a global keepalive (active), the device reboots. The code is 08.10.2.05. I'm unable to search the TAC archive or I would've gone there first.
View 2 Replies
View Related
Mar 27, 2013
I have 2 pair of 11501 switches and 1 pair of 11503 switches on 3 sites(LA, China, Taiwan).Each site has a pair of 1105x switch running as redundancy between them and is a standalone which will not interact with others.Recently a series of interfaces(ports) down happened to every active 1150x switches without any reason and log.Especially today, it happened to active switches at 5:39 AM meanwhile on 3 sites.
View 3 Replies
View Related
Oct 30, 2011
I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
View 1 Replies
View Related
Jun 12, 2012
We are about to upgrade Cisco Load Balancer CSS 11501 firmware from current ver, 8.10.4.01 to 8.10.6.02,this is a production line device (a running 24x7 network), upgrading will create unpredictable results even worst the network will go down.
View 1 Replies
View Related
Mar 1, 2011
We have Cisco CSS 11501 and connected in One-Arm way.Currently there are 4 source sending traffic and 3 server to receive the request. We are using Advance-balancing with Source IP. So the ratio become 2:1:1 or 1:2:1 or 1:1:2.But our target is to do the load balancing in equal ratio.
View 1 Replies
View Related
Feb 5, 2013
I have an issue with the device in subject. I need that some server, listed as service on CSS, can contact a content VIP on the same subnet. To allow that traffic I configured grouping on CSS (group 1) with vip address and an ACL that allow traffic from subnet 10.1.1.0/24 toward same subnet 10.1.1.0/24 and I have bound this ACL with sourcegroup 1. The nat and portmap works but never at first attempt, instead since second attempts it works. Seem like a CSS require to much time to create nat entry.
View 4 Replies
View Related
Jul 18, 2011
cant sign on to my Hotmail
View 1 Replies
View Related
Jun 22, 2011
I've got my ASA 5505 set up right now so that my IPSec clients have to connect using their token as well as username and password. I would like to disable the secondary username and password. Does anyone know if it is possible to have a token only log on?
View 2 Replies
View Related
May 18, 2012
My environment have two device ,a cisco css11501 and a cisco 2960 ,when I reboot CSS11501 then 2960 shutdown fa0/41
I command "sh logging | in 0/41" just up down two time,not five times in 10 seconds
.May 17 11:13:18: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to down
.May 17 11:13:19: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to down
.May 17 11:14:53: %PM-4-ERR_DISABLE: link-flap error detected on Fa0/41, putting Fa0/41 in err-disable state
.May 17 13:44:35: %LINK-3-UPDOWN: Interface FastEthernet0/41, changed state to up
.May 17 13:44:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/41, changed state to up
View 4 Replies
View Related
Feb 3, 2012
I would like configure a CSS content, that uses the sorry service principal in an advanced way.
I am familiar with the primary Sorry Server command and see that the CSS would send all connections to the named service that is configured as the primary Sorry Server.
What I would like to do is to configure the CSS, so that once it’s decided it’s in a “sorry” state (all the services that are configured with “add service” are down) that it load balances to a different set of services.
To explain what I’ve been trying to do in the form of configuration on the CSS, I’ve pasted some pretend config below.
Connections come into IP address 1.1.1.1, which normally get load balanced between 9.1.1.1, 9.1.1.2 and 9.1.1.3.
If 9.1.1.1, 9.1.1.2 and 9.1.1.3 are all down, the sorry service is used and the CSS starts passing traffic to 1.1.2.1, which I want it to load balance between 9.1.2.1, 9.1.2.2 and 9.1.2.3.
The order that I have applied the config, is different to the below, as I set out to configure in this order: secondary services, secondary content, sorry service, primary services, primary content.
The order of the config below is different, because I wanted it in the order that the traffic flows and the CSS won’t take the config in that order!
The wall I have ran into, is that when I try to create the service I have named “Sorry Service”, I get the following error:
%% Service IP Address conflicts with a local I/F, VIP, mg mt route.
[Code] .....
View 0 Replies
View Related
Jun 23, 2011
password problem no online soulution
View 1 Replies
View Related
Jul 9, 2011
I use the right password but nothing works. I can't change it because I can't get any information.
View 1 Replies
View Related
Jan 27, 2013
for two days it will not let me sign into my hotmail account...also two days ago got popup for adobe X?? it would not go away, so I accidently said yes, when it wanted to load onto my computer, I did get it off my computer, but, it keeps popping up and now I cannot get into my personal hotmail account.
View 1 Replies
View Related
Mar 4, 2012
I cant sign in to playstation network and when i try i get the message, error code 80710d36.
View 1 Replies
View Related
May 19, 2011
cant'sign in to yahoo
View 1 Replies
View Related
Jan 24, 2011
sm bus controller has come up with an exclamation point how do i fix this
View 1 Replies
View Related
Jan 30, 2013
We are using some desktops as static ip wired and laptops using automaic ip wireless, issue is that in wireless sinal shows yellow marks on laptops no internet but actually getting internet.
View 1 Replies
View Related
Feb 15, 2011
just today my macbook won't sign onto the internet wirelessly even though there are two other computers in this house that can...
View 1 Replies
View Related
May 3, 2011
I've had a DIR-615 rev b for a while and have had it set up with PPPoE sign on. The DSL modem I am using is a Motorola 2210 setup in bridge mode. All was working well. I recently switched over to dry loop AT&T dsl from AT&T dsl over a voice line.After the switch, I am unable to sign on via PPPoE using the dir-615. If I bypass the router, I am able to gain internet access via modem PPPoE sign on. I've also switched modems (Actiontec DT701D) with the same results. What has changed that would prevent the router from PPPoE sign on? I've verified that all settings on the router were the same before and after the dry loop change (including password).
View 11 Replies
View Related
May 24, 2013
Following a new HDD & install of the OS my Dell 1525 is not showing wifi or bluetooth and is not letting me connect via wireless. I have tried installing drivers but nothing. I can only connect via ethernet. I also tried removing the card and replacing it to ensure it was in correctly but still nothing. The set up menu on boot shows wireless card present and all enabled to factory defaults.
View 6 Replies
View Related
Dec 10, 2012
Cisco E1000 router.connecting directly to the router, internet works. When connecting wirelessly, it works for about 2 minutes, then I get no connection and a yellow ! in the connection setting icon. No wireless internet will work until I power down and restart the router. Then the same problem continues.Today when trying it, it won't even connect for a few minutes. It shows as "connected" on my laptop but it has the yellow ! and will not access the internet. So I am no longer ever able to connect wirelessly. I've done a hard reset already.
View 15 Replies
View Related
Dec 18, 2011
I just purchased the AP1141N and I have created a logon account to access the device via URL which works fine but after 10 minutes it logs me out and requires that I log back on. Unfortunately it won't allow me to log back on unless I reset the device then I have another 10 minutes before it asks me to login again but then it won't accept my logon again without a reset.
I can logon with my account via the console logon but I don't know how to configure the access point via command line so I use the web interface. I have disabled the timing for security but didn't work.
View 2 Replies
View Related
