We are using some desktops as static ip wired and laptops using automaic ip wireless, issue is that in wireless sinal shows yellow marks on laptops no internet but actually getting internet.
View 1 RepliesI am using the cisco linksys E1200 WiFi router. when ever I connect my laptop to WiFi, its show Limited connectivity/Yellow Caution sign when connected.
I try to reconfigre it & also in factory default mode it show same.
network adapter error code 10 in device manager saying the device can not start. window xp/asus mainboard M3A78-CM/AMD Athlon E5200 CPU.Uninstall and reinstall new drivers does not solve the problem.
View 1 Replies View RelatedCisco E1000 router.connecting directly to the router, internet works. When connecting wirelessly, it works for about 2 minutes, then I get no connection and a yellow ! in the connection setting icon. No wireless internet will work until I power down and restart the router. Then the same problem continues.Today when trying it, it won't even connect for a few minutes. It shows as "connected" on my laptop but it has the yellow ! and will not access the internet. So I am no longer ever able to connect wirelessly. I've done a hard reset already.
View 15 Replies View RelatedIt has been 4 months my Router " Wag 120n ". The Router Gives Me A yellow Sign on the network Icon Sying " No network Access " and the wireless Led is blinking with 1 sec interval So
- I cant open Router's Home Page
- there is No ping to 192.168.1.1 " General Failure or Host unreachable " response
- The Only way to get connected again is to replug the router from electricity , it works normally for 5 min and the Yellow Sign shows up again
the Solutions I Tried to fix that up :-
1) Hard reset the 30/30/15 reset
2) Firmware re-flashing
3) Trying an old firmware 1.0.0.12 instead of 1.0.0.16
but nothing of those worked the Only thing that worked for like 20 min the firmware upgrade but after that the problem came up again the problem happens to all Computers on the network wired or on wireless happens on all kind of operations systems win7, xp, vista, (Android for mobiles).
I have the M2N32-SLI Deluxe/Wireless Edition motherboard with onboard wireless. I built this computer myself. I did a fresh install of Windows 7. I installed the wireless drivers from the asus website by putting them onto a flash drive from my laptop and installing them on my desktop.On my wireless signal, I get the yellow triangle with a ! in the middle. Nothing else has been installed. I am at a loss of what to do to get rid of this and just get my wireless to work. We have 3 other laptops and one other desktop that work fine with no issues, but this one desktop seems to have problems.
View 10 Replies View Relatedin some laptops wireless signal showing yellow mark no internet, but we are getting internet
View 1 Replies View RelatedI have several E4200 routers deployed in our library district. In one branch, we have been having sporadic problems with computers not being able to maintain a connection. Typically the computer will connect and then the connection will drop and Windows will display the yellow error triangle on the wifi signal strength display.I have swapped the router with another brand new E4200 with the latest firmware but am still having this problem.
View 6 Replies View RelatedMy internet at completely random of times drops and can take anywhere from 2 minutes to reconnect or 20. This may happen once a day, this may happen 10+ times a day. Totally different all the time. Basically what happens is it I get the yellow triangle on my taskbar where the connection should be saying limited connectivity, sometimes I get a complete red X going through it saying there is no connection. It always reconnects at some point though.
View 6 Replies View RelatedWhat a yellow star on top of my wifi signal bars mean. It says i have excellent signal but when i put security key in to connect it tells me it cant. My other pcs connect and run with no problems.
View 2 Replies View Relatedjust today my macbook won't sign onto the internet wirelessly even though there are two other computers in this house that can...
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR841N
Hardware Version : V7
Firmware Version :
ISP : Virgin Media
The sun sign on the modem has been flashing for a couple of days but I am still getting the internet. Is there anyway I can find out why its doing this? I have tried rebooting but still starts to flash.
I just purchased the AP1141N and I have created a logon account to access the device via URL which works fine but after 10 minutes it logs me out and requires that I log back on. Unfortunately it won't allow me to log back on unless I reset the device then I have another 10 minutes before it asks me to login again but then it won't accept my logon again without a reset.
I can logon with my account via the console logon but I don't know how to configure the access point via command line so I use the web interface. I have disabled the timing for security but didn't work.
we plan to implement the SMB Pro AP541 for a guest access solution.is there a lobby ambassador like on the big wireless lan controller?is it possible to sign a guest a time frame - e.g. guest user has only 60 min access to the internetis it possible to enter a lifetime for the guest user - e.g. guest user can only login until 10.10.2010
View 2 Replies View RelatedI bought an EA3500 because I found that I did not need the more expensivbe router. The problem that I have now is when I sign in to Cisco Connect Cloud both the old and the new router show up. I would like to remove the old router from the list. The old router shows as:CiscoA3518 [offline]
View 6 Replies View RelatedI'm suffering from an annoying problem with my E4200 router. I have a DSL connection. I have my DSL modem in bridge mode and I have my router set up to sign into my ISP's PPPoE to avoid double-routing. This set up worked marvelously with my previous WRT54G and WRT610N routers.Now the E4200 signs me out of PPPoE every ten minutes or so. I have the connection setting on "Keep Alive" but it seems to be dropping the connection regularly. I took the router back and was given a replacement. The new router is doing the same exact thing and now I am beyond the 30 day return limit so I'm stuck with the E4200. I'm running the latest firmware 1.0.03
I reinstalled the WRT610N and the connection is steady but the WRT610N has its own problems (devices connected via wireless cannot see wired devices and vice-versa). I'd like my new router to actually work properly. I've ruled out errors on my end and given that two brand new units of the E4200 generated the same problem I tend to believe it is a design error.
My internet just keeps dropping every 15 minutes or so. I never really have a problem, but for the past week or so I have been having this issue.I don't think it is just wireless though, because my xbox live connection keeps dropping too and that is wired into my router.
If I right click on my connection and click "Status", this is what I get.
IPv4 Connectivity: Internet
IPv6 Connectivity: No network access
I have unplugged my router and modem at least 10 times. I don't know what else to do.
I am getting a small yellow icon in my wireless settings that suggests that there is no internet connectivity even when I do have the internet. It comes when i disable and enable the wireless adapter or when its left idle. My ipconfig and DNS settings are fine.
[code]....
My Desktop (Win 7) and laptop (Acer Aspire 4830T) were talking both ways (after I fixed a Teredo Tunnel problem!) but have now degraded to the point where I cannot setup a Homegroup.The main issue is that although my wireless internet works when I am home (D-Link DIR-615 router), as soon as I leave, I get the dreaded Yellow exclamation on both Virgin Trains and my client's Unsecured wifi (with password protection). These did use to work in July. Can't detect an event when started to go wrong, though could blame Windows Update! Did try System Restore but these keep failing. Using Kaspersky.
[code]....
Ok BEFSR81 (192.168.1.1) is connected to the Modem. I have a cable from one of the BEFSR81's LAN ports going to WRT54G (192.168.2.1) WAN port. My computer is connected to the BEFSR81. I can not access the setup page (http;//192.168.2.1) from my computer, maybe I am not suppossed to be able to do that. The Laptop sees a Linksys wireless connection, but there is a yellow exclamation point over it.
View 7 Replies View RelatedI have a Compaq Presario V3016US Notebook PC. It has Windows XP Home Edition.So onto the problem. If I plug in the Ethernet cord, or try to connect to the Internet wireless,nothing gets picked up.I went into device manager, as I have seen many of you asking whether there is any "Yellow Exclamation" marks, and I found three under the Network Adapters.
View 14 Replies View Relatedcant sign on to my Hotmail
View 1 Replies View RelatedI can't connect to the internet using our wireless router. The signal is excellent but there's a yellow triangle with an exclamation point. It says that there is limited access. I tried resetting the router, checked all the plugs, restarted my laptop., all to no avail. I tried connecting using my phone, and I can go online so the problem lies with my laptop.
I checked my device manager and under Networks, the 6TO4 adapters has a yellow triangle with exclamation point. With a code 10 error. I tried to run 'check for solutions" but I can't connect to the internet. Using my phone, I saw websites dealing with the same problem. I uninstalled all the 6TO4 adapters along with the isatap adapter because it also has the same problem except that it's reporting error 31. Then I restarted my laptop.I can connect to the internet but only through LAN. I still can't connect through my wifi. I tried to reinstall the 6TO4 and isatap but it still shows the same message.
I'm having problem with the router WRT54G2, My laptop - winodws 7- connetcs to the wireless.Then it asks me if I wanna configure the router I saw yes, I give a name to the wireless connection and a password, everything works and come to the end, after that I connect to my wireless connection and a little yellow triangle appears -down right on the signal bar. I resetted the router already and update the firmware.Still won't work. I thought maybe I need to put a static IP but I won't find the DSN Code.
View 1 Replies View RelatedI have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies View Relatedpassword problem no online soulution
View 1 Replies View RelatedI use the right password but nothing works. I can't change it because I can't get any information.
View 1 Replies View Relatedfor two days it will not let me sign into my hotmail account...also two days ago got popup for adobe X?? it would not go away, so I accidently said yes, when it wanted to load onto my computer, I did get it off my computer, but, it keeps popping up and now I cannot get into my personal hotmail account.
View 1 Replies View RelatedI cant sign in to playstation network and when i try i get the message, error code 80710d36.
View 1 Replies View Relatedcant'sign in to yahoo
View 1 Replies View RelatedMy EA4500 is not working. The power indicator light is on but the green and yellow lights on the Internet port are not flashing and the modem the EA4500 is connected to show no activity on that port. Also, the EA4500 is not broadcasting so I can't even connect to it to use Cisco Connect to troubleshoot. I tried resetting it but it did nothing. This has happened before but is usally fixed with a reset.
View 8 Replies View Relatedsm bus controller has come up with an exclamation point how do i fix this
View 1 Replies View RelatedI've got my ASA 5505 set up right now so that my IPSec clients have to connect using their token as well as username and password. I would like to disable the secondary username and password. Does anyone know if it is possible to have a token only log on?
View 2 Replies View Related