I have just received a Cisco SF 200E-24P switch and need to upgrade the firmware. The current version is 1.0.0.12 an need to load the latest (or at least 1.1) to get CDP etc. However when I use the upgrade option in the switch I get an error of.Firmware Image download through HTTP failed. Wrong File Type.I have tried 3 different versions of the firmware and get the same error message each time.
View 4 RepliesWe are about to upgrade Cisco Load Balancer CSS 11501 firmware from current ver, 8.10.4.01 to 8.10.6.02,this is a production line device (a running 24x7 network), upgrading will create unpredictable results even worst the network will go down.
View 1 Replies View RelatedI'm about to upgrade my asa to version 8 from 7. I see a lot of instructions on using tftp to accomplish this. I also see in the GUI where i can upload the image files for version 8. is there any disadvantage from using the GUI instead of a tftp server?
View 1 Replies View RelatedI've got a used WS-SVC-FWM-1-K9 on the way and I'd like to standardize it to the Firewall Module Software Version 4.0. I'm not positive if the current software on it is newer or older than Version 4.0. Is this possible to perform or is the Software as is on these modules?
View 2 Replies View RelatedI can't do hardware reset in wap 200e I try as the manual said but nothing When i connected with lan said there is no lan in my pc in order to access the ip.
View 11 Replies View RelatedI had a strange problem here after upgrading Cisco 3750X.The upgrading was going smoothly, I copied a newer IOS to the flash from another Cisco 3750X through TFTP, changed the boot image.It took a while do to the microcode upgrading, finally, it started to boot up. But when it completes the boot up, I can't see the normal login prompt, but only some strange codes. From what I can see, it seems some decoding problem, as if I plug or unplug a cable from the switch, the strange code pops up again, like in normal situation, the console tells you that the interface is going up and down.
The original image of the switch: c3750e-universalk9-mz.122-53.SE2.bin
Upgrade to image: c3750e-universalk9-mz.122-55.SE3.bin
However, I don't have any problem to telnet to this switch, as it has correct IP address and login configured before the upgrading. I have reboot the switch for couple of times, reconnect to the serial port still doesn't show me anything.I am wonering has any one has met this situation before? detailed message shown after the boot up. cisco WS-C3750X-48 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1449Z04L
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
52 Gigabit Ethernet interfaces
[Code] .....
I've just attempted to uprade the firmware on my WAG325N from 1.0.6 to 1.0.12 the latest, over wireless. It will not work with Ethernet. It started to upgrade and failed with a garbled screen in my browser. No message to reset. Tried a complete reset several times. Pressing reset, power off for 30 secs. When I attempt to connect wirelessly with browser, just get a garbled screen, with no menus.
View 1 Replies View RelatedI'm trying to upgrade the firmware on my BEFSR81 v3 cable router (firmware version 2.45.xxx) on a Mac. I accessed the interface via Safari browser, followed the instructions, got a message saying not to interrupt the process, but it never completed. So I tried it again (downloaded another copy of the firmware update), and same thing. No choice but to interrupt it. My internet connection seems to be working fine, but now I can't access the router via the browser. I don't think the firmware actually updated.
Should I power down the router and then reset it?
I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies View RelatedWe have a centralized Cisco 5508 WLC with 84 APs(1142N) in branches (slow WAN links), Current WLC IOS version is 7.0.220.0.Recently we bought new Aps Air CAP36021-N. These APs are not compatible with existing WLC IOS. If I upgrade WLC, then can I stop propagating newer firmware for old Aps? Because it kills all WAN.
View 9 Replies View RelatedI'm attempting to upgrade to firmware 5.00.38 for my WRT54G-TM router, but it keeps telling me "upgrade failed" after like 3-4 seconds of trying. It says I currently have firmware: DD-WRT v24-sp2 (06/13/09) mega - build 12288. I've tried restetting to factory defaults before upgrading, but doesn't work.
View 1 Replies View RelatedCannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios. They connect ok using Belkin and Linksys routers.
View 4 Replies View RelatedI have a little problem with my new E1200. Before the E1200 I had a WRT160N that was bricked to death by a power surge due upgrading the firmware. Till that moment the WRT160N met al the required specs as told in the description..I have from my ISP a 40Mbit cable line and was always downloading at those speeds wired aswell as wireless...
Now with the E1200 I get the 40Mbit only wired... wireless it only allows it up to max. 20Mbit.I figured that I didn't do anything different than the Linksys I had before..I'm working with a MacBook from late 2007 running OSX Lion 10.7.2, Built-in AirPort Extreme card (802.11a/b/g/n)My wireless setting with a WP2 Personal Security Mode
Region : Bulgaria
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP :
Region : Others
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel.53137n
ISP :
I bought the TL-R2543ND. The hardware version is V1.2. I want to ask, is there firmware upgrading for this version . Here I see only version V1.URL
I've got a mixed stack as follows:
Switch 1 - 3750X-24P
Switch 2 - 3750G-24TS
Switch 3 - 3750G-24T
Running 12.2(53)SE2, IP base. Now I tried upgrading the firmware on the entire stack to 12.2(55)SE4 and ran into this error:(Command: archive download-sw /imageonly /overwrite /allow-feature-upgrade tftp://10.20.20.13/c3750e-universalk9-tar.122-55.SE4.tar)
Error: The image in the archive which would to used to upgade system number 2 does not support that system type.I haven't as yet removed the "3750G-24TS" switch from the stack and re-tried as yet, however, is the expectation that without the 24TS, the upgrade should work?
After unsuccess firmware upgrade, my router is leds always light.How I can recover it?
View 3 Replies View RelatedI was using Remote Desktop between two home computers hard wired through the router and a switch. Now after upgrading to firmware 1.35 I can't get remote desktop to connect. I get an error that I may not have permission, etc. I have the DIR 655 ver A and am running Windows 7 professional on both computers.
View 5 Replies View RelatedVideo streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?
View 3 Replies View RelatedI just upgraded to a E3000 from a WRT54G and I am having some issues with network speed.I have no special settings and have even tried restoring factory defaults and upgrading to the latest firmware to no avail.The time I notice the biggest hit is when transferring files locally on the network (WiFi and LAN).Let me note that I do know the difference between MB/s & Mb/s and the like.I have Comcast 20Mb/s Down, 1.5Mb/s Up (just a FYI, the main issue is local transfers)
With default settings my Laptop (ASUS N82JQ, Atheros AR9285 Wireless Network Adapter), connects to the router at only 65Mb/s (with full signal).Upload seems to be more decent ~600KB/s (Transferring files from wireless n laptop to the gigabit desktop).Download seems to be limited to ~150KB/s (Copying files from the wired gigabit desktop to the wireless n laptop).These speeds are horrible! ~5hrs to transfer 3GB of data!
One of my laptops had a card that was capable of both 2.4 & 5Ghz and I was previously getting ~2000-5000KB/s (2-5MB/s) transfers with this router (But I had to do a system restore on it and reset the router). My ASUS laptop seems to only work with 2.4Ghz though. If I change the 2.4Gh Wireless settings on the router to "Auto(20MHz or 40MHz)" the laptop will connect at 150Mb/s, but the speeds are the same slow speeds as above.
I have 4506e core switch to which 10 other 2960 switches are connected.I want to upgrade thier IOS. how can upgrade it, can I upgrade it one by one or all at a time?
Is there any tool to perform this task?
The company I work have finally decided to enter the 21st century and invest in a new telephone system (Interactive Intelligence) to replace the legacy system which has served us well for the past 10 years. The project has only just started and involves upgrading sections of CAT3 cabling to CAT6, replacing Cisco 3550 switches in one area of the building with Cisco 4507 switches and upgrading our Core switches with Cisco Nexus 7010's. The area that concerns me most is enabling the network for qos as I have very little experience with it. At the moment Im trying to read as much documentation as I can on QOS to bring myself up to speed.
The access layer switches will consist of a mixture of Cisco 3750 & 4507 switches connected to Cisco Nexus 7010 switches which will form a collapsed aggregation & core layer.
Basically, how I should approach this daunting task of making sure the network will support VOIP.
With the new firmware (1.1.2.0) released for SG200 switches, is there CLI now?
View 4 Replies View RelatedRecently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedI have tried to update the firmware of my srw2016 but after this update my switch wouldn't start again.
It shows this message in my console:
Exit from boot menu. Continue with flow.
Preparing to decompress...
Image in address: 0x0 - Check Sum error!
Please download a new image.
Downloading code using XMODEM.
I did not know to update the boot software of my SRW2024 first, then update to 1.2.2b.I need to go back to the 1.0.0.86 firmware.
Is it downloadable and will it work (ie work backwards and then do it properly)? I know how to use hyperterminal and the xmodem protocol if need be.
I have downloaded the new firmware for the SG500. I see there are two files included in the download, a boot file (rfb) and regular firmware image (ros). I have looked and haven't seen anything about the rfb files. I know it is a boot file, but do not know if I should update the boot file first and then the firmware image or vice versa. Also, in my update screen on the SG500, the boot file option is greyed out.
View 1 Replies View RelatedWe have Sg-300-28 serious switches(SRW-2024 k9-EU) and i want to upgrade switch with latest firmware, any info for latest firmware is used for the same ?
View 6 Replies View RelatedI'm trying to upgrade a switch SRW224G4 but without success. Model Name SRW224G4 Hardware Version 00.03.00Boot Version 1.0.0.06
I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
We just purchased this device and was curious if the firmware 3.0.2.0 or 3.0.1.0 has the CLI functionality like the Sx300 models with 1.1.2.0. I find it easier to configure via CLI then the WebUI.
View 3 Replies View RelatedHow do I get the actual firmware for SUBJ? On Cisco site only. 1.0.2 . However, As far as I know It have a 1.0.6 with lot of bug fixes.
View 1 Replies View RelatedI have just attempted to load the latest firmware on an SLM2008, everything appeared to work as expected BUT, the switch is no longer pingable on its static IP doesn't appear to have attempted get an address via DHCP. I have attempted power cycling the switch but it has made no difference. The switch is still switching but I have no management any more. What to do next ?
View 1 Replies View RelatedI want to remove the DD-WRT firmware from my router.It is a TP-LINK TL-WR740N V2.1 router.I want to set it back to its original firmware.
View 1 Replies View RelatedI have a SF300-24P switch running version 1.1.2.0 firmware. I want to get to the latest release (1.2.9.44) - can I upgrade directly to the latest code or do I need to step through all the versions in between?
View 1 Replies View Related