Cisco :: LMS 3.2 Won't Detect Switch 29xx
Dec 7, 2011my LMS 3.2 won't detect my new Switchs 29xx , router 39XX and my 7200 router .
View 5 Repliesmy LMS 3.2 won't detect my new Switchs 29xx , router 39XX and my 7200 router .
View 5 RepliesUsing 'debug ip packet acl# det on a 2911. On an older Cisco router you could set up an ACL
access-list 150 permit tcp any any eq 1023 and then run debug ip packet 151 det and this would give a good debug output for any traffic matching a TCP port of 1023.Now when I try this on a 29xx ( Version 15.1(4)M3 ) I get the screen filling with a lot of multicats HSRP communications.
I have tried rewriting the acl to have other deny statements after the permit to limit the source or destination hosts and/or the ports but the HSRP data is still there.
like this
access-list 150 permit tcp any any eq 1023
access-list 150 deny udp any any eq 1985(code)
We have VPN IPSec tunnels on cisco routers between Remote/Central sites. I'd like to replace the old 2811 by 29xx on the remote sites.So I did export/import RSA key for the certificate as follows:On 2811,But the IPSec tunnel didn't go up, it stayed in MM mode giving "Bad certificate" message in the log.I ckecked and compared the RSA key and certificate between these routers; they are the same in characters.
View 1 Replies View Relatedas my Netgear FVX538v2 router recently died I would like to replace this router by an enhanceable Cisco product. I'm thinking of a Cisco 2901 model that will be connected to the cable modem of my ISP and has to support PPPoE over the WAN port. The Cisco router should provide the following physical interfaces:
+ 2 WAN ports (10/100/1000 Mbps, RJ-45)
+ 8 LAN ports (10/100/1000 Mbps, RJ-45)
+ Serial Port for terminal program access
+ other options the FVX538v2 does provide
Will a Cisco Router 2901 be sufficient to replace a Netgear FVX538v2 device? What modules do I have to purchase?What additional licenses (data, UC, Sec?) do I have to pay for?
I have asked this question in server fault but not getting good answer.Can Cisco switch detect mac address if driver is not installed?
View 7 Replies View Relatedi just bought a new desktop and my problem is as stated in the title. I cant detect my own modem but i can detect others.
View 1 Replies View Relatedwe are trying to integrate ACE 4710 {Cisco ACE 4710 version A3(2.0) } installed on 4506-E with LMS 3.2. LMS is able to detect the 4506-E But LMS is unable to detect the ACE 4710. Tried to find the cisco document for supported devices in 3.2 it shows ACE 4710 is supported in DFM 3.1.1
[url]...
Also need to open tac for the same. but dont have details of LMS. How to open a SR with cisco (what details are required and how to find those details in LMS)
Is there an easy way to detect NAT devices - specifically home wireless routers like those from NetGear or D-Link or Linksys - on my network? I've shut down the ones that are easy to find by looking at the hostnames on the DHCP server, walking around with my phone and capturing the MAC address of the AP then finding a matching MAC address one number higher or lower. But there are still more out there evading me and I need to shut them down.I've read about a method using SFlow/Netflow, but my old Cisco 3750 and 2950 switches don't support that. I've read about a plugin for a Linux based firewall, but I use a Cisco ASA.
View 10 Replies View Relateddetect botnet acitivity from network point of view.
View 15 Replies View RelatedI have a 6506 with SUP1 MSFC2, running IOS. [code] However, its not able to detect the switch module. [code]
View 6 Replies View RelatedWe setup some new CAPWAP AP 3602E in the network and configure the DHCP server option 43 , but the WLCs still cannot detect the APs , Do you know if there any new way to troubleshooting?
WLC: 5508 version: 7.2.103.0
SW:3750E
AP: AIR-CAP3602E-C-K9
I have WLC 2540 and AP 1142..i have configure them both and got connected(WLC can detect the AP) yesterday then i turn off them both and now when i powered up , the WLC cant detect the AP but AP and WLC can still ping each other they communicated at layer 2, both WLC and AP in one IP segment.
here some debug from AP
*Jun 21 13:49:47.784: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.3.2
*Jun 21 13:50:05.913: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Jun 21 13:50:05.913: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jun 21 13:50:05.913: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10. 0.3.2:5246
*Jun 21 13:50:05.954: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jun 21 13:50:06.042: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[code]....
windows xp cannot detect modem
View 1 Replies View RelatedI'm currently using wifi on my desktop but I usually disconnect and use cable. But just recently I do not know when, I can't detect any internet even the cable is attached to the pc
[code]...
Yesterday i used it to play online-game and it's still work properly. But today My friend's laptop suddenly can't detect any wireless network. Wireless light signal is still on. I'm really stupid at technology device like this so, i don't know what to do. Laptop is Levono ideaPad U460 OS win7
View 1 Replies View RelatedI gave this old router (DGL-4300) to someone far away and couldn�t get it work over the phone.Normally, I would just connect it to my cable modem and it detects all the WAN IP�s (IP Address, Subnet Mask, Default Gateway, Primary DNS Server, Secondary DNS Server).However, she lives in a building and her internet comes from the wall where she attaches her Macbook to it via Ethernet. When she connects the router to the wall, the WAN IP�s remain at 0.0.0.0.
View 7 Replies View RelatedMy ipod and my brothers ipod both detect and connect to our wireless network. Our PC connects to the network through a wired connection and is having no problems. I got a new laptop, have Windows 7 professional installed, and my computer will not detect any networks. I even tried unplugging the cable from the back of my PC and plugging it into my laptop, and it still does not detect a connection[CODE]
View 4 Replies View Relatedi have purchased a pendo buddy box and have everything plugged in, but my pc wont detect it?
View 5 Replies View RelatedWhy my router TL-MR3420 can't detect my smart bro (Stick)
View 1 Replies View RelatedJust the other day, I had to restore my laptop to it's factory conditions. Ever since then I have not been able to connect to the router, before I restored my laptop though I was already having trouble with my Internet connections. I have tried troubleshooting but it cannot detect anything wrong with anything. I know it's not the router since I am still able to connect to it via other devices. I restarted the router just in case but that has done nothing.
View 12 Replies View RelatedSo I just finished building my new PC. Installed windows 7. Plugged in wireless network adapter in USB port. It detects it and I'm able to connect to the internet. I download chrome and install it.
I restart the computer. And now it shows I have no network adapters and I can't find it in device manager. Plugged it in again in, used different ports.. to no avail. I plugged the network adapter into another PC and it works.
what linksys router can detect new external IP?
View 1 Replies View Relatedwhen we hooked our computers into our lan swich, which is a 3com dual speed switch 8, all of our machines reported that there was local or no conectivity.according to ipconfig, we all had addresses of 169.254.xxx.xxx, so we manually set the ip addresses, and still nothing.finally, we reset the router, and still nothing?!
View 1 Replies View RelatedI just a bought a new Lenovo Ideacentre K330, and it will not detect any wireless networks. All of my other computers can detect and use the network, but the new computer will not. It's running Windows 7, and as far as I have found, there is no Wireless switch on the actual tower.
View 3 Replies View Relatedi use n5010 dell laptop wifi dw wlan 1501 minicard driver is installed but it cannot detect wifi at the place i live..here the wifi routers are cisco.
View 11 Replies View RelatedI bought a new xps 8300 everthing was running fine last night and this morning my wifi wont connect,there are no errors in device manager and all drivers are up to date.
View 1 Replies View RelatedI am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
How do I fix my network so that my Windows 7 and XP computers automatically detect each other on the network. Right now, they cannot browse each other by computer name, instead I have to type their IP addresses (for example: \192.168.2.5) in the windows explorer address bar, and then I can browse to their shared folders. And under "Network" (in Windows Explorer) each computer only displays itself, and not the other (unless I have already typed in the other's IP address, in which case it displays the other computer as the IP address).
View 3 Replies View RelatedI recently installed Linux Mint 10 (Julia). Having found the network options, it seems unable to find my BTHomeHub2, although Windows 7 finds it perfectly well with 5 bars.Interestingly, the network icon in Linux only shows VPN connections and Wired connections, no wireless section. My computer is a Medion Akoya E4120 D with a Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Network Adapter. The wireless adapter is inside the PC, attached to an internal USB port I'm guessing.So all in all, how do I get my wireless internet to work with Linux Mint 10?
View 1 Replies View RelatedWhen reinstalling windows corp. edition, windows installs, but the cable modem is not detected, and won't connect to internet.
View 3 Replies View RelatedIve just installed Windows 7 on my PC and created a homegroup with the wizard but my laptop isnt detecting the homegroup so i cant "join" it.
My pc is wired to the router and my laptop is wireless.
My HP laptop's wireless does not detect my home wireless network.The wireless is on, there is internet connectivity and other devices at my house detect the network but not my laptop. i hve already spent so much of time in finding out the problem.The driver for the wireless is installed and updated.The service is running. Checked the Wireless Zero Configuration.
View 9 Replies View RelatedMy Compaq laptop (Vista) was working just fine last night, connected to my home wireless network all right and all. Today morning my laptop couldn't detect my home wireless network at all, but it could still detect a bunch of other networks from the neighbours. My iPhone can detect my network with no problems, my desktop computer is wired up to the router, works fine too. It's a D-Link DIR-655. This has happened before but usually gets solved when I reboot (switching off and on) my router. I've tried that, tried restarting my computer too, no use. Haven't tried anything beyond that because I'm an idiot with computers.
View 1 Replies View Related