migrating from LMS 3.0.1 to 4.0.1 it was relatively simple but we had a simple configuration which does'nt run on our new Ciscoworks version:
1) Routers sends SYSLOGS to Ciscoworks server.
2) Our ..CSCOpxlogsyslog.log file updates correctly and saves syslog data coming from various devices.
3) The same automated action we had on LMS 3.0.1 (it was a trivial ALL FACILITIES *-*-*-*-* send email to) does not work on LMS 4.0.1
Have a setup for Cisco LMS3.2.1 which is a recent upgrade, also RME 4.3.2 and CM 5.2.2. Is it possible for the DFM to generate alerts such as email notification to user defined group (subnet grouped). These alerts should be critical in in nature.
View 1 Replies View Relatedwe operate a number of 2106 WLC's some of which are in training centres, we have been requested by one customer that the SSID used for the users in the training rooms is only enabled between the hours of 9am - 6pm Monday to Friday.
As such im trying to find an automated method of disabling said WLAN automatically outside of these hours including weekends.
Im aware that the commands:
config wlan disable "WLAN ID"
config wlan enable "WLAN ID"
Can be used to perform the required function but getting them to trigger at the appropriate time is proving more of a challenge.
I am currently stuck to setup an automated configuration backup for ACE Blades. I found a script to backup the ACE from the Cisco ANM box but unfortunately I am not very familiar with Linux. (script) in place, to "pull" the ACE config from a Microsoft system ?
System State:
ACE IOS A2.(1).5
we want to have full wireless coverage in a big warehouse (120mx90m) and 15 meter Height that will be having big racks (14 meters height) and 2 meter between the racks and the rack itself is 1.5 meter (2 rack back to back), now we will be having scanners and we need to make sure the wireless is covering everywhere.Where is the best place to put the AP, Ceiling? How Many APs per row ? each row will be around 60 meters length.
Is AP 1252 a good choice? The scanners are a/b/g.What i'm thinking of is to put 1 AP per row mounted on the ceiling and antennas facing down because it is hard to mount the APs between the rack because of the automated racking system.
I have a question about NAT behavior on FWSM 4.0. The problem is email server (Company A) cannot connect to email gateway (Company B) on the outside network and it randomly happen. I got this error from server guy "Detail: xlate has blocked the connection between A’s mail gateway and B’s mail gateway". It work fine again after clear xlate on firewall. [code]
1. How FWSM create xlate table like that? I mean it look like NAT0 for 158.137.21.26 but it doesn't has any nat rule for 158.137.21.26 on firewall.
2. What does it mean "connections 24" at the first of line? In the normal time, I only see the connections is 0 like the second line of xlate
3. After clear xlate global 158.137.21.26, the first line of xlate table is gone then email server can connect each other. Does is a bug on FWSM? or This is a normal NAT behavior of FWSM.
I used ASDM to upgrade a 5505 tonight and now I get the error message attached. How/where do I find out which versions are compatible?
View 2 Replies View RelatedI deleted an incoming email titled troy from my email inbox by mistake I need to recover this email as it came from my son in bali [URL] edited by moderator: Deleted Email address to prevent Spam
View 1 Replies View RelatedI have Cisco Catalyst 6500 with IOS Version 12.2(17r)SX5I need real-time monitornig of failed interface, to shut it administratively down and after 5 minutes "no shutdown" it.I think is good idea to use Cisco EEM for this task.My algorithm is below:
1. EEM script is looking for event about failed interface.
2. EEM script is shutting interface down.
3. EEM script is waiting 5 minutes.
4. EEM script is enabling interface.
I know how to configure EEM for steps 1, 2 and 4, but step 3 I do not.
my Cisco anyconnect VPN clients are able to access all of my internal networks accept to another site which has a IPSEC VPN site-to-site. The Cisco ASA forwards the packets destined to this remote site to a Cisco router which NATS the source addresses (pool 10.17.252.0/24) to a 192.168.46.0 range. The remote network is 155.x.x.x which I have included in my internal subnets object-group and added a route on the ASA to route it inside.
I have configured NAT so that it does not NAT anything from the anyconnect client range to the internal subnets. I am using version 8.3(2) and the NAT rule is:
nat (outside,inside) source static SSLPOOL SSLPOOL destination static INSIDE_NETS INSIDE_NETS
I can still not connect to the remote side via the VPN; when I run this throught packet-tracer, I get a failure on phase 6:
Type: WEBVPN-SVC
Subtype: in
Result: DROP
Result:Drop reason: (acl-drop) Flow is denied by configured rule
I cant seem to work out what it is that is blocking it. The NAT rule above is rule 1 in case some other NAT rule is causing the issue..
I was wondering if there is a workaround to have a mac access-list bond to a port security violation action our need is the following: we have a range of 10 mac addresses that can use any port on the 3750, we only want to allow those ones yet we also need to tak action if a denied mac appears on any port of the switch.the only work around I found is to basically go into a port-rage mode and list all the allowed mac addresses under all the ports of the switch. I would also add to that a port violation action. did not test it but should work. problem is, it would be a huge config.I did read that we can create a mac access list and then bind that mac to physical ports wich will actually simplify our solution yet I did not find a way to bind the mac list with a port violation action.
View 1 Replies View RelatedIf we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action? For example maybe email an admin, or send an SNMP trap? Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?
View 2 Replies View RelatedI have two questions about ZBF on ASR1000 with Firewall and Flexible Packet Inspection license:
1 is IPv6 supported?
2 can I use police action in an inspect rule? I want to limit some protocols to low bandwidth. There is no police command in ZBF policy map.
We have a Cisco 2911 router. We installed a EHWIC-4ESG module and configured the router based on configuration below.
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M1.bin"
Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.
7 Gigabit Ethernet interfaces
1 terminal line(code)
Cisco 4500-X do not support egress queing on VLAN interfaces (SVI) which means cannot do a traffic-shapping, is there a work around via policing? I can police the traffic and then on the trunk interfaces do "per-port-per-VLAN" QoS but again only the policing not shapping so I was wondering what is the effect of "exceed-action transmit" command
policy-map SHAPE
class class-default
shape-average 8000000
Versus...
policy-map POLICE
class class-default
police 8000000 4000 conform-action transmit exceed-action transmit
I have RV042 V01 and V03 and RV082 V03.I'm wondering if there's a difference between the default actions taken by the "Logs" interfaces?
In the case of the V01 systems, it appears that I get a Security Notification every hour.In the case of the V03 system, it appears that I rarely get a Security Notification.
while ago, I got a virus that tried to mimic windows activity center. Since then, I have use malwarebytes anti malware, ccleaner and microsoft security essentials to scan and remove the virus.Usually what happens is that I will be using firefox, and all of a sudden most of my programs would exit, and one of those fake virus scanners come up (Microsoft security essentials also turns off if that is important). I open the task manager, and identify the program. I open explorer (as i can't open mbam, or mse) and delete the file. While it is in the recycle bin, I can open mbam (for some reason, it asks what program to open mbam with, I just pick mbam from the list) and I scan, and remove the threats. Then I empty the recycle bin, and use ccleaner to fix the registries. Lastly, I use mse to scan the computer.Everything works for a while until it comes back again....and again....and again. I've tried the same steps in safe mode and again in regular mode. It's still happening.
View 9 Replies View RelatedMy company has an 881-w ISR that provides wireless and wired network functions for our small office (about 20 users). I was attempting to create a new V LAN (another story), and was able to create the V LAN (4) and assign it a new IP. However, when i came in today, and when i attempted to connect to the ISR, the serial console started spewing this over and over:
*Feb 8 13:31:32.479: %SYS-2-MALLOCFAIL: Memory allocation of 8 bytes failed from 0x81528DF0, alignment 0
Pool: Processor Free: 131305952 Cause: Interrupt level allocation
Alternate Pool: I/O Free: 17850656 Invalid memory action (malloc) at interrupt level -Traceback= 0x820168A0z 0x82E4
-Process= "<interrupt level>", ipl= 4 -Traceback= 0x81FF6FC8z 0x820168D0z 0x82E49944z 0x81528DF4z 0x800C3AF8z 0x800C4760z 0x810A1208z 0x810A6F8Cz 0x810BA9E0z 0x810BACBCz 0x80241A24z 0x8025ADE8z 0x8025E2F8z 0x8030ACD4z 0x804E1518z 0x80310368z
[code]....
Now, I did leave the console session up overnight, as that's the only thing that I can think of. As expected, our service contract had expired. I did reboot the ISR, and I am looking to see if this can be fixed, or symptomatic of a larger issue, and time to replace? At this point i can't even get it to stop, and thus cannot log in.
when the supplicant is missing vlan500 is open for port and everything is ok, but when supplicant has wrong configuration something happend and port is always authenticating(every 30s, vlan500 is not assign to this port with bad configuration supplicant) and logs show something like that
Jul 10 10:20:12.362: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A3545161E4 Jul 10 10:20:44.365: %AUTHMGR-5-START: Starting 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %MAB-5-FAIL: Authentication failed for client (001e.3718.7297) on Interface Ga0/1AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-7-FAILOVER: Failing over from 'mab' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11 Jul 10 10:20:44.399: %AUTHMGR-5-START: Starting 'dot1x' for client (001e.3718.7297) on Interface Ga0/1 AuditSessionID 0A0EFF5B000004A45451DF11
version - Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.0(1)SE2
port config:
interface GigabitEthernet0/1
switchport access vlan 104
switchport mode access
switchport voice vlan 200
authentication event fail action authorize vlan 500
[code]....
i put in my email n my password that i only use n its not going through
View 1 Replies View RelatedIm using WCS v7.0, I want wcs to send me an email when an AP goes down. Is it possible to do it on wcs? If so, how?
View 1 Replies View RelatedWe're running LMS 3.2 with DFM 3.2, and at some point within the last month, email notifications from DFM have stopped flowing. DFM is trapping events as they occur and these are viewable through the portal, but notifications that should be going out as email and SMS messages have stopped.
[code]...
Backups going back beyond when this is believed to have stopped working are available if something needs to be restored. If that's the direction I need to go, how do I restore just the DFM portion of the database? If backup restore is not the way to proceed, what other advice can be provided.
I have an issue with my lms 4.2 installation.I have created a fault notication group which sends me an email when an alert is active on a device.Some of the devices are deleted from the inventory, but when I restart my deamon manager. I receive alerts for all the devices I have deleted in the past.I get this email in my inbox.When I check "Monitor - SNMP traps - fault notification group" I can't see any of the devices for which I receive the email alert?
EVENT ID = 00024PS
TIME = Fri 01-Feb-2013 11:03:59 CET
STATUS = Active
SEVERITY = Critical
MANAGED OBJECT = switch
MANAGED OBJECT TYPE = Switches and Hubs
[code]....
I have installed cisco lms4.1, seems to berest all working fine. But am not finding a option to enable email seetings options to send reports. I have already set smtp servers, through whihc threshold alerts are trigering, but am unavle get best practice reports. as per document, email setting option is available under Reports>reports settings. But I cant see email setting option under report setting, only 'set report path' is available.
View 1 Replies View RelatedWant to transfer email and email folders to a disk. I have Windows Vista on my computer and I use Comcast for an internet server.
View 2 Replies View Relatedi keep getting the message install email client how do i do it
View 1 Replies View Relatedi cant send an email from my yahoo email.
View 1 Replies View Relatedneed log-on address for e-mail
View 2 Replies View RelatedI think I've done a wrong move and cancel my company e-mail address.I'm not familiar with this , but is it pssible to restore.??..and if so be as clear as possible for each step to do cause I'm not a computer wiz in that stuff.
View 1 Replies View RelatedI am having almost an Identical issue. It seems that I can do anything I want on the internet, but the second I open hotmail all the problems start. Issues occur on both FF and IE. As with you I am able to continue to get some information on sites that are currently open (for example I will get incoming IMs, although I cannot send replys, and my stream on facebook continues to update). Once this happens I cannot open any new webpage or use the wireless on ANY other device in my house (iphones and printer); wired devices seem to have no issues. I have done everything as far as resetting, updating firmware etc to my router with no luck. I have a netgear dual band router, computers with Windows 7 64bit. It seems that accessing Hotmail on the iphones does not trigger the same issue...
View 4 Replies View RelatedSomeone tricked me by sending false email and gained control of my email address. I tried to log on and change my password but I cannot. How can I regain control. I am not experienced with computers. I would also like to learn more about computer basics to start.
View 2 Replies View Relatedcant access my hotmail
View 1 Replies View RelatedI had the email host setup a test account for me to use. I have tried logging in to the email account on four different networks. On three of the four networks, I can successfully log in to webmail. On the fourth network, I cannot. Why would one network block access to this certain pop host? I am running an Apple Airport Extreme router, and I have not set it to close any ports--at least not knowingly . Need getting pop mail to work on a network?
View 2 Replies View Related