Windows Action Center Malware Keeps Coming Back?
Dec 25, 2011
while ago, I got a virus that tried to mimic windows activity center. Since then, I have use malwarebytes anti malware, ccleaner and microsoft security essentials to scan and remove the virus.Usually what happens is that I will be using firefox, and all of a sudden most of my programs would exit, and one of those fake virus scanners come up (Microsoft security essentials also turns off if that is important). I open the task manager, and identify the program. I open explorer (as i can't open mbam, or mse) and delete the file. While it is in the recycle bin, I can open mbam (for some reason, it asks what program to open mbam with, I just pick mbam from the list) and I scan, and remove the threats. Then I empty the recycle bin, and use ccleaner to fix the registries. Lastly, I use mse to scan the computer.Everything works for a while until it comes back again....and again....and again. I've tried the same steps in safe mode and again in regular mode. It's still happening.
View 9 Replies
ADVERTISEMENT
Nov 21, 2012
For some reason when I'm watching a HD video or I'm downloading a file, on my HP laptop my wifi decides to stop,disconnect and then start up again This never occurs on my iPhone iPad Xbox or any other laptops in the house.
View 1 Replies
View Related
Apr 15, 2013
Cisco 2800, 12.4(23b) router has two VPN tunnels to other Cisco devices.
Authentication uses certificates from a PKI CA server. Under normal circumstances all works fine, both crypto sessions up.
After a power cycle (having first saved configs) however, the crypto sessions are stuck in DOWN-NEGOTIATING.
The certificate on the router still looks valid.
The only way to get the sessions back up is to renew the certificate, which seems strange as the existing one appeared to be still valid.
View 5 Replies
View Related
Jun 13, 2011
I can't remember the last time I connected to the Windows media center on my Xbox 360 but I know recently I have tried to run a game server on the PC that the media center runs on. I was trying to do this by setting up a static IP. Here is the thread I posted to ask questions about it. I also used Hamachi to do the same thing. It basicly creates another netowork for you to connect to other people on, I guess. When I started using it another network appeared in my network and sharing center.I have tried reseting my modem and router. I've checked my network settings on my PC and my Xbox 360 and they both look like they use to look before I tried to use my PC as a server.
View 13 Replies
View Related
Sep 18, 2011
I don't have a DVD drive in my Windows Media Center PC that's connected to my TV. I was wondering if there's a way I can insert the disc into a networked PC that has a DVD drive and watch the movie on my Media Center PC.
View 1 Replies
View Related
May 3, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I've just set up my new WDR4300. I have a media center PC that is able to access the router and a media center extender that is also able to access the router as well without issue. However, the media center pc cannot see the extender. I found this post which describes a similar issue and talks about another tp-link router that "Blocks SSDP Search or Notify packets, so the PC can never find the Extender during setup."I believe this may be the issue but am unsure where to start looking or how to correct it. I have enabled UPnP on the router and am still having no success. I believe it has to be something with the router since everything works correctly if I hook my old router back up.
View 1 Replies
View Related
Apr 29, 2012
Successfully setup X Box connected via DPC3925 WIFI router to to Win 7 Media Center? I am sure I had uPNP enabled and I tried turning off Firewall for home network but no luck!
Adding the extender from Media Center always claims it can't find the X Box (Yes, I did enter the 8 digit key exactly as displayed on TV).
View 1 Replies
View Related
Aug 4, 2011
I recently replaced my Linksys WRV54G with a Linksys e2000 where I stream H.264 vido in 480p from one computer connected over gigabit to my Media Center running on Windows 7 64 bit connected at 10/100.
Before the router change, I was able to playback video over the network with no problems. If I connect the Linksys WRV54G again, the issue goes away. The Linksys WRV54G does not have gigabit and I have read related issues of video stuttering over gigabit.
View 4 Replies
View Related
Oct 7, 2012
My wireless key is turned on, and I know it has nothing to do with my router at my apartment because my friend's wireless connection works fine. I know it has something to do with my own computer because I am in college and I cannot connect wirelessly off-campus at my apartment or on-campus using my school's wireless network connection.
View 14 Replies
View Related
Mar 24, 2012
Running Windows 7 Home Premium, Dell OEM install.The symptoms are:No wifi connection, adapter does not show in dev manager. It is just missing, scan for new hardware doesn't find it.Will not connect via ethernet...no internet access.It will not renew or release its IP address, says there is no device in permissible state for this operation.The computer had obvious malware, there were a bunch of sketchy items in the startup. I ran several malware tools, they found and removed hundreds of items. The computer had an expired installation of Trend Micro, I removed that and used the removal tool from Trend to be sure it was gone. I do not know if it has had other security software installed in the past, I ran Norton and McAfee removal tools since those come on most PCs.
I have tried resetting winsock and TCP/IP, to no avail.I know I need to probably reinstall wifi drivers to get the card back, but that's next after I solve the overall connectivity issues. If this were my PC I would have just Re-OSed by now, and I may just suggest that to him.
View 3 Replies
View Related
Dec 19, 2011
My computer was recently infected with the XP Antivirus 2012 rogue virus. I believe that it has been removed from my computer, but I am unable to connect to the internet. I am unable to obtain an IP address. The IP address is 00000 and the Submask is 0000. My operating system is Windows XP and I am using a High speed cable connection
View 5 Replies
View Related
Mar 13, 2011
I have an older (but still good) computer...it's gotten to the point of being somewhat less than functional due to remnants of old programs and viruses and such scattered thoughout it. After a few weeks of fighting it to get it to run properly I think at this point my best option is to reformat the hard drive and re-install the original OS from CD. I've already backed up all my important files to CD and DVD, pretty much ready to pull the trigger here.... Concerned about getting back online! I have cable internet (Bresnan)...I want to make sure I have the proper drivers and any applicable software to get back online, I know people have had problems with this after reformatting....The computer is a dell dimension 8400, I'll be returning it to a windows XP home edt. with sp2 from the OS CD, (circa 2004ish). I plan on putting a comodo firewall installation on a CD as well, so I have a functional firewall in place (instead of the crappy norton one that will get re-installed) when I go to get the sp2 updates and the sp3 and updates and not just end up re-infected again...
View 3 Replies
View Related
Sep 1, 2012
I switched to Intel(R) PRO/Wireless 2200 BG by mistake and now I can't get connected through my wireless! I did not mean to do this, but I have not been able to switch back to Windows to control my wireless.
View 3 Replies
View Related
Nov 25, 2012
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
View 4 Replies
View Related
Dec 4, 2011
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies
View Related
Apr 11, 2013
I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies
View Related
Nov 25, 2011
I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
View 5 Replies
View Related
Oct 19, 2012
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies
View Related
Jan 8, 2013
I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?
View 7 Replies
View Related
Apr 14, 2013
I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?
View 2 Replies
View Related
Feb 29, 2012
Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.
View 1 Replies
View Related
Jan 7, 2013
I'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 7 Replies
View Related
Aug 28, 2012
securing a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).
View 11 Replies
View Related
Apr 7, 2013
I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
Which RJ11 pairs will be connected each other [code]
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.
View 2 Replies
View Related
Dec 15, 2011
I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.
View 3 Replies
View Related
Jul 2, 2012
I have Cisco Catalyst 6500 with IOS Version 12.2(17r)SX5I need real-time monitornig of failed interface, to shut it administratively down and after 5 minutes "no shutdown" it.I think is good idea to use Cisco EEM for this task.My algorithm is below:
1. EEM script is looking for event about failed interface.
2. EEM script is shutting interface down.
3. EEM script is waiting 5 minutes.
4. EEM script is enabling interface.
I know how to configure EEM for steps 1, 2 and 4, but step 3 I do not.
View 2 Replies
View Related
Jul 4, 2011
migrating from LMS 3.0.1 to 4.0.1 it was relatively simple but we had a simple configuration which does'nt run on our new Ciscoworks version:
1) Routers sends SYSLOGS to Ciscoworks server.
2) Our ..CSCOpxlogsyslog.log file updates correctly and saves syslog data coming from various devices.
3) The same automated action we had on LMS 3.0.1 (it was a trivial ALL FACILITIES *-*-*-*-* send email to) does not work on LMS 4.0.1
View 1 Replies
View Related
Jul 18, 2011
my Cisco anyconnect VPN clients are able to access all of my internal networks accept to another site which has a IPSEC VPN site-to-site. The Cisco ASA forwards the packets destined to this remote site to a Cisco router which NATS the source addresses (pool 10.17.252.0/24) to a 192.168.46.0 range. The remote network is 155.x.x.x which I have included in my internal subnets object-group and added a route on the ASA to route it inside.
I have configured NAT so that it does not NAT anything from the anyconnect client range to the internal subnets. I am using version 8.3(2) and the NAT rule is:
nat (outside,inside) source static SSLPOOL SSLPOOL destination static INSIDE_NETS INSIDE_NETS
I can still not connect to the remote side via the VPN; when I run this throught packet-tracer, I get a failure on phase 6:
Type: WEBVPN-SVC
Subtype: in
Result: DROP
Result:Drop reason: (acl-drop) Flow is denied by configured rule
I cant seem to work out what it is that is blocking it. The NAT rule above is rule 1 in case some other NAT rule is causing the issue..
View 1 Replies
View Related
May 22, 2012
I was wondering if there is a workaround to have a mac access-list bond to a port security violation action our need is the following: we have a range of 10 mac addresses that can use any port on the 3750, we only want to allow those ones yet we also need to tak action if a denied mac appears on any port of the switch.the only work around I found is to basically go into a port-rage mode and list all the allowed mac addresses under all the ports of the switch. I would also add to that a port violation action. did not test it but should work. problem is, it would be a huge config.I did read that we can create a mac access list and then bind that mac to physical ports wich will actually simplify our solution yet I did not find a way to bind the mac list with a port violation action.
View 1 Replies
View Related
Jun 2, 2011
If we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action? For example maybe email an admin, or send an SNMP trap? Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?
View 2 Replies
View Related
May 26, 2013
I am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?
View 6 Replies
View Related
Mar 23, 2011
I have two questions about ZBF on ASR1000 with Firewall and Flexible Packet Inspection license:
1 is IPv6 supported?
2 can I use police action in an inspect rule? I want to limit some protocols to low bandwidth. There is no police command in ZBF policy map.
View 7 Replies
View Related
May 1, 2012
We have a Cisco 2911 router. We installed a EHWIC-4ESG module and configured the router based on configuration below.
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M1.bin"
Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.
7 Gigabit Ethernet interfaces
1 terminal line(code)
View 3 Replies
View Related