Cisco Routers :: RV042 Hangs Three Or Four Time In Single Day
Apr 18, 2012
We are using router RV042 since last three it's working fine with single broadband connection but when we are using as a load balance it will hanged three or four time in a single day. I have updated firmware also but still my problem is not resolved
Below is my router detail.
CPU: Intel IXP425-266
Firmware version : 1.3.12.19-tm (Feb 13 2009 13:03:21)
DRAM : 32M
Flash : 8M
Latest firmware is v4.1.1.01-sp.bin but it will required v3 hardware, I don't know how to check hardware version.
View 1 Replies
ADVERTISEMENT
Sep 15, 2011
I was hoping that the latest firmware would fix my (2) 'bugs', but it did not. We are using the RV042s at our remote medical clinics as an end-point VPN router to our Nortel 1700 VPN router, replacing our old Nortel Contivity 100s.When I try and do a reset when connected remotely via the WAN interface, the RV042 hangs and will only reset by re-powering.
View 1 Replies
View Related
Nov 2, 2011
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies
View Related
Jan 1, 2013
I have 2 RV042 routers with identical firmware (1.3.13.02-tm) and settings. One router is a backup that sits in a box, but both experience this problem. The WAN port gives very poor performance most of the time. Download speeds range from normal, 25mb, to less than .5mb. Pings from my command prompt or the routers "Diagnostic" page, even to the cable modem, are almost always above 500ms. However, pings to internal resources are fast, usually under 5ms. If I connect my laptop directly to the cable modem I have no speed issues. The problem occurs whether I use WAN1 or WAN2.
If I restart the router, speeds are fine for a few seconds and then it begins to slow down like someone is turning down a dial. We also regularly experience a complete internet disconnect quite often, and when it happens, the ping results are the same when it comes back up, almost like the router is restarting itself. [code]
View 1 Replies
View Related
Mar 14, 2012
I have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running Win XP PRo SP3.
View 1 Replies
View Related
Mar 15, 2012
I have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running WinXPPRo SP3.
View 4 Replies
View Related
Aug 24, 2011
I just got a new RV042. V3 Hw.For setup and testing before putting it in action, I've attached the WAN1 side to my internal network.But it fails to get an IP address, and the log shows: "Infinite lease time, exiting".My current router on the LAN is giving out DHCP addresses with 3 hour lease time, and I've checked with the PC's on the LAN that this is correct.The routers DHCP status shows that the lease time for the RV042 is 3 hours ahead.So why does the RV042 complain about long lease time ?Is there a way to avoid this error from occurring?
I have tried to change from 'Gateway' to 'Router', but this does not change anything.Also tried a factory reset, with no luck.Fw is upgraded to the latest 4.0.4.02
View 2 Replies
View Related
Mar 6, 2013
The website [URL] started giving me this error : The server at forums.d2jsp.org is taking too long to respond. I am directly connected to my service provider's box (The brand is "Arris"). The issue seems to have started as soon as I uninstalled google chrome (reinstalling doesn't fix it). My last resort with reinstalling windows 7 64bit.
My service provider is Videotron (Quebec, Canada) I can see the front page directly from their IP adress: [URL] but as soon as I hit any link it goes back to the connection time out error.
The tracing route is :
1 7 ms 6 ms 5 ms 10.189.16.1
2 15ms 15ms 15ms 216.113.124.17
3 31ms 31ms 32ms 216113123.174
4 * * * Request timed out.
View 2 Replies
View Related
Apr 1, 2012
I'm new to an ASA 5510 running 8.4(3) and am trying to figure out something regarding time ranges in ASDM. I simply want to allow a single port during business hours only (I'm not concerned about open sessions needing to be closed). So as an example I add a rule something like:
(RULE1 on the internal interface) SRC=INTERNAL DEST=ANY SERVICE=RDP ACTION=PERMIT with a time range set for weekdays 8:00-16:59. I did a test after 5pm on a weekday and was still allowed to do RDP to a server (from INTERNAL), and after using the packet trace tool saw it was still passing through due to a rule a couple lines down (rule 4) that allowed a port range that happened to include port 3389. So my question is if I specify an "allowed" time range and someone attempts access outside that time range, why doesn't it drop it right there? I guess I'm assuming that anything outside the "allowed" time range would be dropped but that doesn't seem to be the case. I'm also assuming the rule base is processed top to bottom.
View 2 Replies
View Related
May 1, 2013
Few months back I had purchased this Router. But I did not use it till last week. Since the time I have installed it, it does freeze often (between 5 to 30 hours).
I can connect to devices within the subnet, but not elswhere. I have to remove the power and plug it back for it to respond. I have updated the firmware to the latest one that was on the Cisco site.
View 2 Replies
View Related
Jan 2, 2012
Using RV042 router,have an office with 4 computers XP PRO SP3 and only 2 need to use the VPN connection.problem is each one will connect just fine BUT when one is connected the other will not connect untill the other is disconnected.have another office with very similar setup (same quickvpn client) (same router)and i have 2 computers connecting at same time just fine.have checked all i can think of.
View 2 Replies
View Related
Jan 31, 2011
I'm trying to figure out what's wrong in a LAN having 70 computers.There are three routers in the same subnet with three switches (kinda crappy). DHCPs are off.The problem is that randomly the routers are losing their configurations or the network hangs a lot. There is no problem in the routers (tested many times).The thing is that when i start packet sniffing over the network using wireshark there's a big flood (over 10.000 packets in a sec) coming in a internal ip inside the network ex. 192.168.1.60.Next thing is that when one of the routers shuts down manually, the other one is losing it's config. Today, when i went to check 192.168.1.60 i saw the power plug was not connected, when i re-plugged it the flood was gone. (the computer was turned off).I enabled SPIs / firewalls in all of the three routers and there is no problem yet.
View 5 Replies
View Related
Dec 1, 2012
This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
View 1 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Sep 16, 2012
Just purchased an RV220W for a customer to replace a WRVS4400N that had no support for One-to-One NAT and have found the One-to-one NAT for this router is only marginally better.
I have three WAN addresses and three devices to map them to. With the RV0xx I've used the following configuration over a dozen times.
WAN Address 1 - the router's public address Port forward HTTP, HTTPS, and SMTP to Windows Small Business Server 2011 Email and Remote Web Access are accessible at remote.company.com
WAN Address 2 One-to-one NAT to private IP address of Ubuntu Server Add the following access rules: Deny allAllow HTTP from any to private IP address of serverAllow SSH from my company's static IP to private IPAllow FTP from my company's static IP to private IPCompanies website is accessible at company.com and I can update the website with SSH and FTP
WAN Address 3 One-to-one NAT to private IP address of the Hyper-V server's Intel RMM module (Lights out remote management) Add the following access rules: Deny allAllow HTTP, HTTPS, and all RMM ports from my company's static to the RMM modules private IPI can access server at rmm.company.com from my companies network connection
My problems are as follows:
The One-to-one NAT option now requires you to specify the service you'd like to forward (Note: service, not services)If you select the Any service which is the only way I can see to have more than one service, there is no way to add any specific Allow or Deny rules because the Destination box is grayed out on the access rules page.This results in my Ubuntu server only having HTTP forwarded to it and my RMM module having all ports opened up to any IP address. There must be some way around this! I don't understand why the Destination IP option is greyed out for all Inbound access rules. I have been using this same configuration with the Cisco RV0xx, many Sonicwall firewalls, as well as several Cisco ASAs. Obviously this is not an ASA but this implementation of One-to-one NAT is useless!
View 5 Replies
View Related
May 11, 2013
I'm trying to set up a single web server in a DMZ using the RV042G and the docs seem woefully inadequate to explain how this is accomplished.
I've attach a picture of my setup..
I'm assigned a single Public IP.. in the example I've used 172.16.5.22 and so I've set the WAN interface for static IP.
The DMZ port is not obvious how to set up.. So I've chosen to define a private subnet and throw the web server in there. As I activate the DMZ, I specify a "subnet" and its address as 10.10.10.1, which I'm assuming goes to the DMZ/WAN port. I assign my webserver the address 10.10.10.3.
I leave the Access rules in their default condition.
I am a little unsure as to how to setup the static IP info for the web server.
Gateway: 10.10.10.1 ?
DNS: 10.10.10.1? or 172.16.5.1?
Problem #1
=========
My first problem is that the webserver cannot access the Internet. I get a timeout when I open the browser. I've tried every address there as the gateway and DNS..
Problem #2
========
If a person on the WAN side is attempting to connect to 172.16.5.22:80, how does the RV042G know to send it to the 10.10.10.3 device? It doesn't know what address the webserver is assigned; I just gave it a 10.10.10.1 address as the subnet address.
I think I'm missing something, conceptually here.
Can, in fact, you use the RV042G in this fashion with only a single public IP address? There is almost no information on how the router actually routes traffic when you choose either 'subnet' or 'range' (where the DMZ is in the same subnet as the WAN)
View 6 Replies
View Related
Nov 5, 2012
Can I connect two routers on a single internet modem. I need a router that is isolated from a public wi-fi connection. The routers need to operate independently.
View 2 Replies
View Related
Feb 19, 2013
I have a phone line and am using a adsl 2+ router for my pc. Now I wish to install a new Tp-link adsl 2+ wireless router for my lap which is used upstairs. and I wish to connect this wireless router to the same phone line with another splitter.
View 1 Replies
View Related
Mar 21, 2012
I've got two houses about 5 miles apart anyway the phone co let me have an off premesis extention at no extra charge two phones that use the same number in the two locations they said i can use my dsl at the other location but i would have to use the same modem/router at both locations iam pretty sure i cant use the dsl at both locations at once but is there a way i can set up two routers on the same phone line where i dont have to carry modem/router back and forth.
View 1 Replies
View Related
Feb 28, 2011
We are in the process of installing time clocks at some of our sites around the USA. Our security department has asked that the time clocks be completely isolated from the rest of the network. The time clocks will be administered by ADP via a centralized firewall utilizing NAT. We have multiple subnets available at each site. Let me give an example to calrify what I would like to do. Example: Site A has 10.168.19.0 /24 user subnet and is configured for VLAN1 using 10.168.19.1 on the router as the default gateway. I would like to use subnet 10.168.20.0 /24 for the time clocks, configure it for VLAN2 and use 10.168.20.1 as the router gateway address for VLAN2. This should allow me to NAT one of our additional public IP addresses to the 10.168.20.1 gateway address thus completely isolating the time clocks from the remainder of the network. Problem is I have not done this before so I'm a little confused about how to configure it in the Cisco 3750 switches.
View 6 Replies
View Related
Jan 28, 2011
This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies
View Related
Apr 7, 2012
I am trying to create a VPN between an SRP547W and a Cisco IOS router, in this case a UC540.I am running firmware 1.2.4 (003) Jan 11 2012. Now I can do this with an SRP527W and many other routers successfully. Including other IOS routers 1801, 1941 etc.
The issue I have is on the SRP547W I cannot create more than one IPSec Policy through a single IKE policy. I require this to route multiple v lans to our remote site. When I try to add an additional IPSec Policy I am give the error "IKE policy has been used by other IPSec policy"
This is possible to do on the SRP527W with latest firmware. I have tried rolling back to earlier firmware but instead I am given an error about overlap. Latest release note for this firmware suggest this issue was already resolved.
View 7 Replies
View Related
Feb 27, 2012
I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
View 5 Replies
View Related
Mar 6, 2012
We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
View 1 Replies
View Related
May 20, 2012
i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies
View Related
Sep 23, 2011
Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
View 0 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Sep 27, 2012
Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
View 2 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Jan 14, 2013
I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
View 2 Replies
View Related
Apr 19, 2012
I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies
View Related
Feb 6, 2012
Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies
View Related
