Few months back I had purchased this Router. But I did not use it till last week. Since the time I have installed it, it does freeze often (between 5 to 30 hours).
I can connect to devices within the subnet, but not elswhere. I have to remove the power and plug it back for it to respond. I have updated the firmware to the latest one that was on the Cisco site.
Region : India
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : BSNL
I Bought this w8968 a month back.. It was working alright till a few days back. When i connect and start browsing or downloading, it goes OK.. but after a few hours(sometimes 2, sometimes 1), It stops responding and I couldn`t ping 192.168.1.1 either through WiFi/Ethernet. Status indicators for DSL/WIFI/Internet/LAN all glowing as though nothing wrong with them..? The router is not that much hot when this happens.. When i switch off the router and then on, The Prob gets solved only to reappear again in 1/2/3 hrs..
we're facing a weird issue lately with a Cisco 2821.An interface stops responding after a few hours.The only way to bring it 'up' again is:
Hardcode: duplex or speed
or
shutdown -> no shutdown
there are no errors in the "sho interface" and no errors or entries in the log.
FastEthernet0/0/0 is up, line protocol is up
Hardware is Fast Ethernet, -
Description: Infopoint
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
We are using router RV042 since last three it's working fine with single broadband connection but when we are using as a load balance it will hanged three or four time in a single day. I have updated firmware also but still my problem is not resolved
Below is my router detail.
CPU: Intel IXP425-266
Firmware version : 1.3.12.19-tm (Feb 13 2009 13:03:21)
DRAM : 32M
Flash : 8M
Latest firmware is v4.1.1.01-sp.bin but it will required v3 hardware, I don't know how to check hardware version.
I'm trying to figure out what's wrong in a LAN having 70 computers.There are three routers in the same subnet with three switches (kinda crappy). DHCPs are off.The problem is that randomly the routers are losing their configurations or the network hangs a lot. There is no problem in the routers (tested many times).The thing is that when i start packet sniffing over the network using wireshark there's a big flood (over 10.000 packets in a sec) coming in a internal ip inside the network ex. 192.168.1.60.Next thing is that when one of the routers shuts down manually, the other one is losing it's config. Today, when i went to check 192.168.1.60 i saw the power plug was not connected, when i re-plugged it the flood was gone. (the computer was turned off).I enabled SPIs / firewalls in all of the three routers and there is no problem yet.
View 5 Replies View RelatedI was hoping that the latest firmware would fix my (2) 'bugs', but it did not. We are using the RV042s at our remote medical clinics as an end-point VPN router to our Nortel 1700 VPN router, replacing our old Nortel Contivity 100s.When I try and do a reset when connected remotely via the WAN interface, the RV042 hangs and will only reset by re-powering.
View 1 Replies View RelatedI have a problem with the RV042G V01 router manufactured 12/2012.
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies View RelatedI have a RV082 that has an issue keeping an IPSEC Gateway to Gateway VPN running from itself to our ASA 5510. At 8 hours of connectivity (I can almost set a clock to it) the Tunnel will say it is connected on the RV082 but on the ASA 5510 the tunnel is not up.
If I click on disconnect on the RV082 under the VPN Summary page things will come back up. from the ASA 5510 side there is nothing I can do to get things back (ping inside "vpn network" or even trying to make a connection to a networked VPN machine).
To make things more complicated I have another VPN on the RV082 to a PIX 506e that works with no issues. I also have another RV082 at another location with the same settings that keeps its tunnel with the ASA 5510 with out any issue. Some things I have tried to try and fix the issue are:
I upgrade the firmware on the Rv082 V3 from 4.0.0.7-tm (what it was shipped with) to 4.1.1.01-sp) - This seemed to have no effect.
on the RV082 I have changed the MTU from automatic to 1428 and 1452 - all this does is make the connection to the PIX 506e unstable like it is for the ASA 5510 I have changed this back to automatic.
since the time of stability seems to be 8 hours I have changed the "Phase 1 SA life time" and "Phase 2 SA life time" to 28800 both at the same time and individually - This seemed to have no effect.
The current configuration on the RV082 are:
Local security gateway type: IP Only
IP address: (local ISP provided static IP address)
[Code]......
i have an ipsec tunnel between two rv082 routers. (1 v3 Hardware and the other with v2). On both devices are the latest firmware installed.
Everything working fine, the routers establish an ipsec connection but after about two hours, the router with hw version 3 freezes.... nor the wan neither der lan interface is pingable. I can only pull out the power cord. Below attached are the ipsec settings. It´s a Gateway to Gateway connection
This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
I have an N750 DB router and it has been rebooting every few hours for no reason. This has just started happening about 4 days ago. I don't know why but when I check the system logs its filled with the following. [code]
View 2 Replies View RelatedIve set up a rvs4000 with two vlans, one as a bussiness network and the other as a guest network. Everything works fine and the networks can not see each other. I would like to add wifi and I would like to do so with keeping both networks separate. I have a used 1130AG access point and was wondering if I could use this single AP for both networks. If so, how would I go about doing so? Is there a better suited AP for my needs?
View 4 Replies View RelatedI have an RVS4000 running V2.0.2.7 firmware that gives me an "Invalid Character(s) Found" error message when I try to edit an existing ACL.
I'm trying to deploy 57 of these routers and would like to be able to use a pre-built config dropped onto each router.
I initially planned on editing the exported config with a find&replace for my local LAN addresses. Since that didn't work the next reasonable solution would be to edit the ACL list (much more tedious, but still better than hand-entering every ACL on all 57 devices).
when this bug will be addressed? Alternatively, if there is an offline configuration editing tool I would be one happy camper to have it!
I have an RVS4000, not installed. How can I tell from the unit or the packaging that it is a v1 or a v2, without installing and switching it on (which I don't want to do now) ? Are v1 branded Linsys and v2 Cisco ? Can you tell from the date on the package (mine says copyright 2011) ?
View 1 Replies View RelatedI don't know if my vendor mislead me, but I need to do this: There is a public subnet in my office, not a 192.168.x.x, but a real Public IP.The reason is that we do VOIP and those are only servers. I installed a RVS 4000 in that location, and assigned a PUBLIC Ip to BOTH the WAN and LAN, since when I connect from outside, using either QickVPN or another identical router, I need to be assigned one of the PUBLIC Ip's on the remote LAN. That is the whole idea of the project, to locate servers remotely and make them use our set of PUBLIC IP's. Well, so far I cannot connect either with the Quick VPN client, or using the VPN Wizard. It goes and creates the tunnel, without error, but when I click test, it fails.
View 2 Replies View RelatedWe have backup and other traffic over our vpn which is affecting our ip phone service between two sites. Our consultant suggested implementing QOS over the VPN to give the phone traffic priority. Is this possible with the rvs4000. Is there any good source saying how to do it. Is the setup of the QOS on this router similar to another router where this has been discussed.
View 1 Replies View RelatedI have problem with bandwidth management on my RVS4000.
That is the way how i done it:
All traffic (TCP & UDP on all ports)
IP range 192.168.0.2 - 192.168.0.2 (My IP adress)
Guaranted download speed 1kbps
Maximum download speed 5000kbps
after saving setting and rebooting router I have maximum download speed on my PC 12000kbps, Why QOS doesnt work ?
I am getting ready to setup an RVS4000 so we can use the VPN functionality of it, but I am not quite sure of the correct way to integrate it into our network though. I do not need site to site, just the client portion of it for a few salesmen/off site people to use. I have never used or setup a VPN before, so I'm learning everything as I go along.
We are in the middle of switching our ISP and I am waiting to set this up until the new service is live so I can test it prior to moving the rest of the company to the new ISP.
We are switching to Comcast, and will have 5 static IP's available to use. Currently, the firewall does all our NAT and is the forward facing device on our network. I would like to leave the firewall in place (although I am setting up a new firewall for the new internet connection) and have th RVS 4000 sit behind it and receive VPN traffic from a WAN to LAN rule We currently have a 192.168.100.0/24 network.
Do I need to setup another /24 network for the VPN to function behind (and still have access to the 100.X network), or is there a way to allow everyone who connects to receive a 100.X ip address from our DHCP server. I'm not sure how to set everything up with the WAN/LAN connections on the RVS4000 to acheive this.
We are running a domain on a 2008R2 server. The clients will be using laptops that are already part of the domain, if that will make a difference.
I'm trying to setup a VPN tunnel between a Cisco RVS4000 on our side and a Cisco ASA5520, to connect a machine on our local network to a test server on the target side.
We have all the settings setup correctly and the tunnel is up and running, however, our local machine can't connect/ping to their server. I've tried a trace route both from the machine and from the RVS4000 itself, and they both get stuck after getting past 192.168.1.1. Is there any routing or NAT-ing that I need to do on our router? Or is there a problem somewhere else?
I'm having an issue with a Linksys RVS4000 which doesn't appear to be behaving as I think it should.I need to forward a port (Single Port Forwarding) through to an internal NAT host. However, I only want that host/port to be accessible from one host on the internet, for security reasons.
I have created the port forwarding entry and this works fine. I then created two rules in IP Based ACL - one to block all access to that port from the WAN interface and one to allow access from a single host.
However, it appears that when a port forwarding entry is added, it will completely bypass the ACL and allow all traffic for that port/host by default.Is this the correct behaviour?
Firmware version is v1.2.11
I'm currently dealing with a weird problem on a Cisco RVS4000. I'm trying to connect to a IPSEC VPN Gateway (NETASQ) located on the LAN side of the RVS4000. I'm using Green bow vpn client on the WAN side of the RVS4000. Basically I'm trying to get through the RVS.My VPN config is OK because i tested it on the LAN side of the RVS.
The RVS is configured like this: NO VPN configured.
Block WAN Request :OFF
FIREWALL,IPS,DDOS are OFF
NAT forwarding on for UDP 500 and 4500 directed from the wan to the ip of the VPN gateway. Seems right because iv managed to do this with other routers (different brands) on another site.I've wire sharked my vpn client and i keep getting ICMP destination unreachable (PORT UNREACHABLE) after my ISAKMP launching packet.Can the RVS nat these ports ?
I've been trying to disect this problem for a few months to no avail. The router allows me to connect to outside FTP only when IPS is enabled. The moment I disable the IPS functoin, the connection hangs and does not connect to a server. Reason I'd like to keep IPS disabled it is because it's eating up half of bandwith when enabled.RVS4000
View 2 Replies View RelatedI have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies View RelatedI have an RVS4000 with FTP download issues. I have the latest v1.3.3.5 software and the latest ISP (1.5). Regardless of any settings changes, my FTP downloads always timeout. I have tried a new basic router and had no issues, so it is not the PC, FTP software, or the ISP. I have even put my PC into the DMZ and still no resolution.
View 1 Replies View RelatedDoes the Cisco SB RVS4000 router support 802.1x authentication for the WAN port?
View 2 Replies View RelatedI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.
None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
I work for a company that recently upgraded to a Cisco RVS4000 router in place of a failing D-Link router. I configured the RVS4000 to utilize the same address space as the D-Link previously did (192.168.0.0 Network Address, 255.255.255.0 Subnet Mask, RVS4000 in Gateway Mode with IP Address 192.168.0.1, DHCP Scope from 192.168.0.101 - 200 managed by the RVS4000) before installing it on the network. I powered down the D-Link as well as the cable modem, then all of the workstations in the office. Then, I installed the RVS4000, powered up the cable modem, and once it was ready, powered on the RVS4000.
When devices connect, the RVS4000 is assigning them an IP address in the 192.168.1.0/24 subnet, instead of the 192.168.0.0/24 subnet. I have verified that the RVS4000's GUI is showing the correct settings, but connected devices are not picking up addresses from the correct address pool. In troubleshooting, I went to each workstation, released and renewed their IP addresses, and they picked up addresses in the correct subnet. I thought everything was solved, but the next day, the same problem resurfaced.
I left the DHCP lease time at the defaul value "0", which according to the unit's documentation should correspond to a 24-hour lease period. I suspect this is why I had to renew the clients' IP addresses the next day (today), but I still don't get why the RVS4000 wants to give out addresses in the 192.168.1.0/24 scope. Could this be a holdover from the factory settings?
Additional Information: I did not set up any VLANs on the network and the office only requires one subnet as there are not a lot of devices connected, nor do we need the traffic segragated. The VPN functions of the RVS4000 work fine. Using the QuickVPN utility, I can access the network and resources on the network remotely without issue.
I am having problems with the RVS4000 ver 1. I cannot download files from the web. Firmware is up to date. As an example, if I try to download from pdf995's site, I get a "page cannot be displayed error. If I try to download current files for my flight planning software (like charts, etc.), the download hangs and never completes. I have bypassed the RVS4000 and connected directly to the broadband router and there are no problems. We have a 15MB cable connection.Follow-up - It appears the issue is file size. At pdf995's site, downloading a 2.5MB file works, but the 9 MB file does not. The file sizes for the flight planning software are rather large - 100-200 MB, and they hang as well. Connecting directly to the cable router does not cause this problem. The RVS4000 is set for Gateway mode.
View 6 Replies View RelatedMy new RVS4000 (2.0.2.7) connects the WAN via PPoE with dynamic IP which is held at DynDNS and normally I see the RVS4000 via a router-to-router-VPN. That works fine so far, but every "some" days the router looses WAN connection (and with ist VPN). When this happens, last DynDNS-update is hours ago, so it didn`t reconnect. Looking on the routers site, the LAN is fully functional for clients that have got their DHCP-Information. New clients don`t get DHCP-Info (IP-address, DNS), both do not have internet access. The router`s WAN-summary shows, that it thinks to be "CONNECTED" but with empty WAN-IP and DNS entries. Klicking "DISCONNECT" and then "CONNECT" again solves the problem so far. The loss of connection is not the periodic break from the IPC, which is correctly identified and reconnected as configured. I wanted to trace the problem with the log, but there is also a bug. It stops logging at some time completely - neither email-log nor local log, so I never happend to be lucky to hit the point of loss of connection. Also the local log provides a first and next pages, but the next pages are always empty - not really useful.
View 3 Replies View RelatedThe local router is behind a fiber firewall/router; the rvs4000's ext ip is thus 192.168.1.2, not visible from the net. The firewall/router is a dyn ip, with a dyn dns name mapping to it. The remote (some NetGear thing) is also dyn dns, but it is not behind a firewall.
I want to cook a vpn from the local lan subnet to the remote lan subnet.
It worked fine when both ends were NetGear.
I think it would be ok if somehow I could thell the rvs4000 that the local Security Gateway Type be just FQDN; it can't be IP+FQDN because the remote end doesn't know anything about that kind of thing; it can do IP or FQDN or a couple other confusing things.
We are an A/V integrator and AMX shop and provide our clients with support through the use of VPN tunnels from our RV042 router to their mostly RVS4000 routers.Support is provided through access of remote site equipment using VNC, Telnet, FTP, etc. from multiple PC's at our main office.Netbios is not turned on, but the remote sites have the ability to access equipment on our local LAN should they know our private IP address range.Is there any way to limit the acces from the remote sites back to our LAN while maintaining our access to the equipment on their LAN?I know that one can limt the IP address range on on end of the VPN, but I would like to limit the ability of remote sites to gain "any" access to our LAN. If there's any way to just prevent all traffic from an IP address range on the remote site, that would also do.
View 1 Replies View Related
