I recently purchased a RV082 in hopes of increasing the thruput of my network with multiple users. I initally did have issues with the router locking up and stop functioning every so often, but it seems I have fixed that (so far as I can tell). The main problem I'm having now is the "Load-Balancing" functionality. Because of certain websites I would like to route all HTTP traffic through WAN 1. I've tried doing this by using (System Management > Bandwidth Management > Type: Priority) and making all HTTP traffic a high priority on WAN1 but HTTP traffic still goes even amongst both of them. I've even tried using the Firewall to block all HTTP traffic on WAN 2 and that failed be too. Even with my superior interface know-how, I'm getting no-where with this task.
Also, as less important ambition. I would like to separate a port forward on port 80 so that I may host two website via my two WANs. I've read somewhere that using the firewall instead of the Forwarding function would work, but I was unable to accomplish that task.
I have a RV082 connected to a Comcast business-class internet with 6 static IP's one-to-one routed to specific internal hosts. This configuration has been stable for several years.
A few days ago, the RV082 stopped routing most of the external static requests to their specific internal hosts. External machines only display the "Can't connect to the webpage" error. Rebooting the RV082 re-enabled correct operation for about 30 minutes, then it failed again.
I pulled out my backup RV082, flashed it with the current configuration, and swapped it in. It acted the same - external statics route correctly for about 30 minutes, then it just stops.
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
Have win7 system, cisco WIRED 1720 router, ~1.5mb frame relay via C&WPanama, nortons antivirus installed. IP config dump is at the bottom, but in this event, I don't think my problem is local.An important work-related chat quit working today, and I have narrowed down the issue to not being able to connect to the provider website from my current location. (I can connect via US proxy, but cannot run the java applet via the proxy, it seems it is still trying to go from here to there).
The site I am trying to reach is host7.parachat.com, IP 64.13.158.24
I can load this page (just a landing page comment) as well as their main pages via us proxy, but time out trying to load directly. Fiddler returns a 502 error, socket connection failed.
have tested on 3 machines (all on same router), then on a laptop which hadn't been booted or updated in over a year (also on same router). Trying to find a free wireless network to test with the laptop, but that hasn't been found yet.
I am trying to finish a project and i now have a very un-natural networking question, but i figure that this is the correct place to ask it.
Tools: Routing Device = Router. Test App = Creates and Sends Packets through my machine's NIC via NDIS Driver. WAN = Internet. VPN = Connected over WAN.
I am trying to route/forward/nat promiscuous packets "TO" the Internet to finish my project. The packets are not addressed to my routing device, but it must take them and forward them on to a VPN connected over the WAN. The packets are actually created by my NDIS test app. This means that the packets will be generated on my local LAN, but will not contain the MAC or IP of the routing device. So they will only enter my routing device while it is running in a promiscuous mode.. how would you try to route promiscuous packets out to the internet?
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0 mask: 255.255.255.0 gateway: 192.168.188.2 hop count: 1 interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup Local Security Gatewaytpe: IP Only Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
Experiencing a strange issue with v3 hardware. After a short period of time, I cannot log into the web administration - either locally through standard port or remote through non-standard port get login prompt, enter correct username & password, page refreshes with blank background and first page (status?) never shows.power cycling the router restores access to the web administration page, for an uncertain period of time before it barfs again.
I was running older firmware, updated to newest 4.2.1.02 (?) and same problem. Only thing that is better is the internet didn't completely lock up when I tried to access the administration page, like it did on the older firmware.
I have an RV082 for use in our office. I wanted to create a public acess point on a different subnet/vlan and so configured port 8 of the RV08 as VLAN2. When I plug a laptop into this port it immediataley gets an IP address from the DHCP server on VLAN1 and can communicate with the rest of the network.I thought the whole point of the VLAN option was that this shouldn't happen - what I've incorrectly configured?
I have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
I am setting up a SBS 2011 Essentials sever using a rv082 router. I have a decent understanding of how everything is suppose to work, but execution has been sloppy. My aim is to set up a central storage location, back up services, remote access and VPN. Yesterday I had set up dhcp and dns roles on the sever, configed port forwarding and firewall setting on the router, at that point I was just bouncing around everywhere trying to get stuff to work, clearly not the best way I know. Before I left I reinstalled sbs for a couple of reason, along with resetting the router to default.
I'm trying to setup a VPN between an RV042 V3 and an RV082 V2 router. They get connected but no traffic gets through the tunnel. I tried with and without firewall,DPD, Keepalive, forward secrecy but nothing worked. What should I do? I don't want to throw out the V2 routers. V3 to V3 connects fine.
I did install server system with mscs and Domain controller and Active directory.I want to connect this dc/ac server from other places such as korea / and japan.
I have a public IP But our country ISP Don't open 135/445 port for security. So I can't connect DC/AC server from other places.At this time i did read many article and find good way to handle it. Is it possible for other servers to connect DC/AC server by using the RV082 VPN service.
I've been having trouble with the internet connection speed on my Mac. I originally noticed the problem when my mail kept timing out whenever I sent an attachment, I went to different forums trying to find the solution but nothing really worked, so I found work arounds for the email and lived with it. Recently the company I work for moved offices and I was no longer behind the RV082 and my internet ran better dispite the slower connection. Once we finished moving, I needed to use the Dual Wan Load Balance feature of th RV082 so I set it up in the new office and my internet was slow again. Unfortunatly in the new office there are several more Macs than just mine so I really need to get it working. Currently we have 2 seperate networks for PC and Mac and I really need to get them on 1. Is there a setting I may have overlooked or is it not going to work with Mac.
