Cisco Routers :: Rv082 - Can't Check Enable Vpn Tunnel
Sep 8, 2011According to the manual rv082, if you wan to use vpn.. check the enable
But I can't check enable botton... it's disable So i can't check
ADVERTISEMENT
Cisco VPN :: V2 And V3 RV082 Routers - No Traffic Gets Through Tunnel
Feb 13, 2012I'm trying to setup a VPN between an RV042 V3 and an RV082 V2 router. They get connected but no traffic gets through the tunnel. I tried with and without firewall,DPD, Keepalive, forward secrecy but nothing worked. What should I do? I don't want to throw out the V2 routers. V3 to V3 connects fine.
View 1 Replies View RelatedCisco Routers :: RV082 Split Tunnel Not Working?
Aug 21, 2012I have a RV082 v2 with Firmware 2.0.2.01-tm with a Site-to-Site VPN to a Cisco ASA5510.
The PCs behind the RV082 can not see two webservers behind the ASA5510. Both servers have full DNS registration and are accessable from other sites with RV042 routers.
Cisco Routers :: RV082 V3 VPN Tunnel Backup Not Available On RV016
Jun 1, 2011VPN tunnel backup is not available on the RV016 firmware version 4.0.2.08 (it IS on the RV082. The data sheet and the manual for the RV016 is wrong. I have purchased several RV016 hardware V3 and several RV082 hardware V3. Both have the same current firmware version. We have noted that the RV016 does not have the VPN tunnel failover option found in the RV082. It also does not have split DNS (noted in the manual. A I would have thought that the firmware would provide equal options on the RV042, RV082, and RV016.
View 2 Replies View RelatedCisco Routers :: RV082 To ASA 5510 Tunnel Freezes After 8 Hours?
Apr 18, 2012I have a RV082 that has an issue keeping an IPSEC Gateway to Gateway VPN running from itself to our ASA 5510. At 8 hours of connectivity (I can almost set a clock to it) the Tunnel will say it is connected on the RV082 but on the ASA 5510 the tunnel is not up.
If I click on disconnect on the RV082 under the VPN Summary page things will come back up. from the ASA 5510 side there is nothing I can do to get things back (ping inside "vpn network" or even trying to make a connection to a networked VPN machine).
To make things more complicated I have another VPN on the RV082 to a PIX 506e that works with no issues. I also have another RV082 at another location with the same settings that keeps its tunnel with the ASA 5510 with out any issue. Some things I have tried to try and fix the issue are:
I upgrade the firmware on the Rv082 V3 from 4.0.0.7-tm (what it was shipped with) to 4.1.1.01-sp) - This seemed to have no effect.
on the RV082 I have changed the MTU from automatic to 1428 and 1452 - all this does is make the connection to the PIX 506e unstable like it is for the ASA 5510 I have changed this back to automatic.
since the time of stability seems to be 8 hours I have changed the "Phase 1 SA life time" and "Phase 2 SA life time" to 28800 both at the same time and individually - This seemed to have no effect.
The current configuration on the RV082 are:
Local security gateway type: IP Only
IP address: (local ISP provided static IP address)
[Code]......
Cisco Routers :: RV042 To RV082 Tunnel / NAT-T And Slow Performance?
Feb 18, 2013I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:
- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
How can I troubleshot this slow performance?
Cisco Routers :: RV082 Freezes Every 2 Hours When Using Ipsec Tunnel
Jul 5, 2011i have an ipsec tunnel between two rv082 routers. (1 v3 Hardware and the other with v2). On both devices are the latest firmware installed.
Everything working fine, the routers establish an ipsec connection but after about two hours, the router with hw version 3 freezes.... nor the wan neither der lan interface is pingable. I can only pull out the power cord. Below attached are the ipsec settings. It´s a Gateway to Gateway connection
Cisco Routers :: RV082 V4.0.4.02 - Tunnel To Main Office (IPCOP 1.4.21) Fails
Oct 27, 2011I'm using a RV082 with latest firmware v4.0.4.02tm in one of our branch offices. Sometimes the tunnel to the main office (IPCOP 1.4.21) fails.
Both sides display the status "tunnel connected" but IP traffic doesn't go through. If i try to ping the main office using the RV082 diagnostic feature, the RV082 seems to run into a loop...the window continues refreshing without any error message and i'm not able to cancel the test. If I restart the RV082 using the web interface, the "diagnose" and VPN problem still exists, even if the web interface told me that the device did a restart.
The only solution is to to a cold restart of the RV082. After that, the VPN tunnel works again....
This problem occurred 3 times in the last 3 weeks. I never hat this problem with previous firmware versions at this ot other sites.
Cisco Routers :: RV082 V3 Load Balancing (Protocol Binding) With IPsec Tunnel?
Mar 14, 2013We have tried a variety of options in an attempt to use Load Balancing (Protocol Binding) with an RV082 that has a site to site IPsec tunnel with another RV082. Both are v3.
Here is the issue. We have dual ISPs, one has great bandwidth, but we incur overages. The other has mediocre bandwidth, but has unlimited usage.
GROUP1 - We want most PCs to use the "unlimited" ISP for general surfing, email, etc. (Bound all ports for range of internal IPs to ANY dest to WAN1)
GROUP2 - We want to use the "faster" ISP for our VPN tunnel (mostly RDP and SIP traffic). (Bound all ports for range of internal IPs to ANY dest to WAN2)
So far everything works. The router will route traffic appropriately and GROUP 1 uses WAN1 and GROUP 2 uses WAN2.
Unfortunately, sometimes GROUP1 users need access to resources over the VPN (WAN2).
There is something not right with the routing. For example GROUP1 can ping and receive responses from devices on the other side of the tunnel, but GROUP1 can't access intranet sites on the other side of the tunnel. They also can't RDP to PCs on the other side of the tunnel.
Why does the router correctly route ICMP, but not RDP?
We've tried adding additional protocol binding rules for specific ports(80, 3389, etc) and ip ranges (both local and remote) to see if we could force GROUP1 traffic destined via VPN through WAN2, but it doesn't work.
Shouldn't VPN tunnels created and configured in the RVs not adhere to protocol binding? It just seems logical to me, but maybe I am missing something.
Cisco WAN :: 1941 Router - Enable IPSec Virtual Tunnel Interface With Tunnel Mode IPv4
Sep 23, 2012I'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies View RelatedCisco VPN :: ASA5540 Any Command To Check Tunnel Up-time
Mar 17, 2011I am using cisco ASA 5540, Is there any command to check the tunnel uptime?
View 2 Replies View RelatedCisco VPN :: ASA5500 / Command To Check Tunnel Up-time?
Jun 27, 2011I am using ASA5500 series box which has a site to site tunnel terminated on it.Is there any command by which we can check the up time of the tunnel.
ASA# sh isakmp sa
Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)Total IKE SA: 1
1 IKE Peer: x.x.x.x Type : L2L Role : responder Rekey : no State : MM_ACTIVE
Cisco Firewall :: Command To Check IPSEC Tunnel On ASA 5520?
Jan 7, 2013Need to check how many tunnels IPSEC are running over ASA 5520.Tried commands which we use on Routers no luck?
View 6 Replies View RelatedCisco VPN :: 3000 Network Address Is Allowed Down Tunnel / Check Phase 2 IPSEC Proposal
Nov 4, 2012I need to check and possibly change which Network address is allowed down a tunnel and check our Phase 2 IPSEC proposal. How would I do this on a VPN3000?
View 3 Replies View RelatedTP-Link ADSL2+ Wireless :: IPSec VPN Tunnel Between TD-W8950ND And RV082?
Dec 21, 2012Region : Others
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.3.1 build 120406 Rel.32903n
ISP : PTCL
I am trying to establish IPSec VPN Tunnel between Linsys RV082 and TP-Link TD-W8950ND but failed.
Linksys Wired Router :: VPN Tunnel Disconnect Between RV016 And RV082
Jun 2, 2011Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082. Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD) are checked.
Linksys Wired Router :: Setup VPN Tunnel Between RV082 And WRV200
Feb 23, 2011I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies View RelatedCisco VPN :: How To Enable Split Tunnel On PIX 501
Nov 17, 2012I have several PIX 501's and one of them is extremely slow accessing network resources and does not have Internet access. I would like to use split tunnel and have them access the Internet throught their DSL connection and any traffic for network resources sent over the VPN. How can I improve the speed and set up split tunnel via the command line? I dont have the PDM software so I guess I will need to do all the configuration via the command line. Below is the configuration:
PIX Version 6.3(1)interface ethernet0 autointerface ethernet1 100fullnameif ethernet0 outside security0nameif ethernet1 inside security100enable password k4HlcGX2lC1ypFOm encryptedpasswd y5Nu/Nt1/5dK8Iuf encryptedhostname
[Code].....
Cisco Routers :: Set A VPN IpSec Tunnel GW To GW Tunnel Between RV110W
Oct 17, 2012I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
Networking :: To Tunnel All Routers Traffic Through SSH Tunnel With WRT300n
Jul 24, 2012Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies View RelatedCisco :: Check Load Balancing On The Routers Using BGP?
Apr 8, 2011How is the best and easiest way to check kind of load balancing on the routers using BGP (Border Gateway Protocol)?
View 6 Replies View RelatedCisco Routers :: VPN Between Two RV082 Routers Not Working?
Aug 7, 2012We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
Cisco Routers :: How To Check The Website History In RV-120W
Sep 9, 2012How can i check the website history in router?I want to know the website which the user explored through the router.
View 1 Replies View RelatedBelkin Routers :: N150 - When Check MAC Address Filtering It Seems To Be Disabled
Dec 25, 2012I have a Belkin N150 wireless router. I have enabled MAC Address Filtering as an added level of security. However; whenever I access the router, and if I check that page; the check mark for the option to enable the filter is always blank.
I have checked the option, clicked Apply Changes, and logged out of the router. i went back in this morning, to check the security logs. (Looking like someone is trying to jump on my network) I didn't see anything there, but when I checked MAC Address Filtering; there was no check mark indicating that the filter was turned on.
Cisco Switching/Routing :: Command To Check Memory Slot In 3800 Routers?
Nov 13, 2011I remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies View RelatedCisco Routers :: LAN To LAN Routing RV082?
Jan 29, 2013We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
Cisco Routers :: Rv082 Configure One-to-one Nat
Nov 17, 2011isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
Cisco Routers :: RV082 VPN Passthrough
May 9, 2013I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
Cisco Routers :: RV082 / No Connection To ISP
Nov 12, 2012I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies View RelatedCisco Routers :: RV082 NAT To Other Subnets?
Jan 12, 2012Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies View RelatedCisco Routers :: VPN Fail With RV082
Jan 14, 2013I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
Cisco Routers :: VPN Not Working With RV082
Jan 24, 2012I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
Cisco Routers :: RV082 Restarts Itself
Jul 28, 2010we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.