in the QoS-section of the SRW2008P web-interface I can choose only between Disable and Basic, Advanced mode is greyed out.
I've created a new ACL but QoS Advanced mode isn't available.
What can I do to activate it?
Boot Version: 1.0.1
Software Version: 1.0.4
Hardware Version: 00.03.00
I am specking a SRW2008P-K9 switch for a customer. They are using MM 62.5 fiber. I need to know what Gig SFP will work for them. I am also quoting them a WS-C3750X-24P-S.
View 1 Replies View Related I try to connect Siemens SIP IP phone to switch LinksysSRW2008P with PoE for scheme:
main switch <-------> linksys <-------> phone
I can't have access to Linksys by local network or web interface, so I connect through COM port and reboot the device and restore all settings to defaults. There was another linksys switch with the same default IP in my network, so I've tried to change ip address for my Linksys device. After that I can ping switch IP without lost packages successfully and partly access to login page by web, but including Linksys to the local network causes decreasing all network working speed, so the web administrative form can not be loading at all. In both cases (default ip or another one) the set isn't working, so I can't have access to the phone by ping or web interface. The cable to main switch inserts to port 1 and green rectangle indicator is flashing rapidly. The cable to the phone inserts to port 2 and orange indicator is lighting, green indicator is flashing slowly. Interestingly, only one port has status UP (port 1), all another port has status DOWN. If I replace cables ports with each other, only the port where cable to main switch is inserted, will have status UP. The phone station is getting power from switch in both cases. I've tried to change Spd/Dpx ports' parameters, used DHCP for getting IP, but I've gotten no result. How can I solve the problem? Is Linksys switch worked or defective?
Is it possible to reset this switch oif yo uare unable to get into the console or web interfaces?
View 2 Replies View Relateddoes the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedWe have a project in which we are using 34 Cisco SG200-18's each with a MGBLX1 (LC Single Mode Fiber) SFP mini-GBIC.All the fiber's come back to one building where we must "bridge" all 34 fiber connections. What hardware should be used to accomplish this? A L2 switch? For example, a 12 port SFP Switch with Fiber SFP's accepting the first 12 fiber connections, then other switch with SFP for the next 12 and so on, until there is a overall capacity of 36 and having patch cables between the 3 switches?
what cisco or non cisco hardware would work with these SF200-18's to accomplish this?
my computer was on a lan but suddenly stopped to be part of it.The other coms can see him on the network but mine one cant see anybody.I ve tried everything is written on this site and everywhere on the net but the problem remains.The network id tab is still disabled.im running xp pro,no media center and my antivirus is kaspersky.
View 2 Replies View RelatedI was using my laptop using wireless last nite without any issues.Today i could not get the Internet and noticed under my wireless assistant it says wireless lan disabled ,it is grayed out so i cannot re-able it.Have tried rebooting ,switching router off etc without success.
Never had issues before the router is belkin N router and my os is vista.
I'm trying to secure my dir-615 and I can get in to the web site but the connection wizard is greyed out and the manual set-up is alos greyed out even though I can select manual set up?
View 2 Replies View RelatedI have a n Ipad 4 with bad Wifi when connecting through a DL835, Firmware Version: 1.02. Other devices are fine and apparently i should try disabling WMM. I can see WMM but it's grayed out and i cannot disable.
View 1 Replies View RelatedWhen I launch Monitoring & Report Viewer and select one of the report (TACACS authorization for example) I want to filter the search with Interactive Viewer, but I can't cause all options are grayed. I've heared that some flash is needed but I've got plugins installed and nothing changed.
Can I run in in demo version? cause I've read that there is an add-on license which "Add-on licenses are available to support deployments that are larger than 500 devices (AAA clients) and to support advanced monitoring, reporting and troubleshooting functionality"
The enable button is grayed out on my windows XP laptop so I need to know how to enable it.
View 2 Replies View RelatedI am using USB internet connection. I am trying to connect internet, it shows all the signal but connect button is grayed out.
View 1 Replies View RelatedI got a problem with my netgear WNDR3400V2.As u see in this picture the box allow guest to access my local network is greyed out.I made the router an access point and have no clue how to make it normal again.
View 2 Replies View RelatedMy Compaq Presario V3015's Internal Wireless Adapter has died so I recently bought an Linksys Expresscard WEC600N to replace it. After installing the software (The Linksys monitor) everything on the program is grayed out except for "exit" which closes the program. After looking at device manager, the adapter isn't even listed their. For some reason, even when just plugging the adapter in after an uninstallation of the software and a restart of the computer, the device never gets detected even when it is clearly on (two blue lights for Power and Link/act). I've tried switching to Windows Wireless Zero connection but under network adapters, it doesn't even show a wireless option, just an LAN one. I'm pretty sure its not so much a hardware issue as it is a software one. Everything works fine except for anything related to wireless capabilities on this laptop.
View 4 Replies View Relatedi've a problem with my SF300-24 routing. That's my network configuration:
Port 1 to 12 assigned to VLAN 10
Port 13 to 23 assigned to VLAN 20
Port 24 has an ip 10.17.7.254 to connect with my deafult route, beacuse I've also a Linksys RV042 router, connected in turn with my ISP router, having an ip 10.17.7.1.
On a SF300-08, how to work with CLI and not with the Console Menu Interface ?
View 4 Replies View Relatedhow to access the CLI mode in cisco sf 302-08p 8-port 10/100 Managed switch. I treid the every method they mentioned in the Admininstration guide.I am not able to enter the command debug-mode and comand menu after resetting the default password. After logging in, its directly guiding me to switch main menu.
View 3 Replies View RelatedWe have a problem with NLB on a SG500-28P which is a major issue for us.
I am investigating a problem together with Microsoft Support about a download/upload performance issue with a Microsoft Forefront TMG array which is connected to a single SG300-28P. Àpparently this issue exist on every NLB array we implement. I am now at the point we asume the SG500-28P does not handle NLB in unicast mode very well.
We have a network topology as shown below:Please note the actual public IP Addresses are hidden and the internal IP Addresses are diffrent, for security reasons.
Our SG500-28P is configure in L3 mode. It hosts three subnets you see above. The two TMG servers are configured with NLB (in unicast mode) on the Internal Network and External Network interface. It is connected to the internet and our internal network. These TMG Servers are in fact Edge Servers. Our other servers and client are in a different VLAN. The default gateway flows through this NLB Cluster [10.250.0.254].
Problem: When a client uses its default to connect to the internet the performance is very and very slow. With an internet connection of 10/10 we get 10/2. With an internet connection 100/100 we only get 7/1!.
Now we have tried everyting we can imagine. I can't write down all, because that would be a lot. One thing is worth notice; When we move the client to the same VLAN as the NLB Cluster and the client uses 10.250.0.1 as its default gateway, the problem still exists. But... when the client uses 10.250.0.254 as its default gateway the performance is outstanding 95/95! Apparently if traffic for the NLB Cluster is routed through the SG300-28P the performance drops like a rock.
I have never seen this before with SG300 series switches, although this environment is different. Normally I would configure NLB in multicast mode. But the switch does not allow to add static ARP entries for multicast MAC Addresses.I know NLB in unicast mode introduces switch flooding and such. But why does the SG500 not handle this right? Is there anything I can do about it?
The switch SG500X-48 has 4 SFP+ ( 10G ) ports - XG1, XG2, XG3/S1, XG4/S2 - and two configuration modes - standalone and "native stacking".
Can I use XG1 and XG2 SFP+ ports to connect servers when "Native stacking" mode is active ?
So it seems like the SG300 series (have here sg300-52) can be run as standalone unit and also in stacking mode. but i can not find any documentation or howto for this.
View 8 Replies View RelatedI'm setting up two vlans and I would like all of vlan 2 to only have access to the WAN router on vlan1 at 192.168.30.1.
VLAN1 192.168.30.x
VLAN2 192.168.31.x
I've setup the VLANS and static routes and I'm able to access the WAN router at 192.168.30.1 from the 192.168.31.x network and everything is fine.
I'm getting an error setting up the IPv4 based ACL that is designed to allow the 192.168.31.x network access to only the 192.168.30.1 WAN router.
The first rule I setup is to permit source 192.168.31.0 / 0.0.0.255 dest 192.168.30.0/0.0.0.255 to allow all traffic to from the 192.168.31. net to access the 192.168.30.x net. Then I was going to deny the dest of 192.168.30.1-255 but I'm not sure of the wildcard to use for that.
I'm not clear on the wildcards but I'm also getting the following error when I setup the first ACE rule:
"MIB Index is out of range.Index must be bigger then 0 and Existing ifindex.."
I suspect the error is related to how I'm using the wildcards?
My SF300-24 switch has been working 100% as a backup switch for a client of mine. At my clients premises it was running 3 Vlan's and doing inter VLAN routing. When my client received their original switch back, I obviously brought my SF300-24 back to the workshop, reset it back to Factory defaults and tried to do a fresh installation on it. I can not get it to change from Layer 2 to Layer 3! I installed the latest firmware but still no go.
Everything works a 100% via the console, but when I go to the System Mode menu and try and edit it, it justs sits at layer 2 and will not chage to layer 3!
Our customer use catalyst switch that spanning tree be PVST+ mode.I take SG300 connect with this catalyst switch.Does it support ?If it support,how to config on SG 300 ?
View 1 Replies View RelatedEvery "once in a while" (about a week with my network load), the SG300 crawls to an almost standstill of all IPv4 activity (haven't got IPv6 enabled here yet, so I can't comment wether this applies to IPv6 as well). It seems pure L2 transmissions is not affected, but L3 definitely is (down to 20mbit as opposed to the 600+ rate I usually get).
Soft-rebooting the switch (via the webgui) useful, and the intervals of the crashes seem related to total bytes transmitted, not time. I have jumbo frames enabled, and disabled flow control on on the switch and all hosts.
Firmware Version is 1.0.0.27, md5 1987292110f5657e74308dde30c03dc4 Boot Version is 1.0.0.4 md5 4c9a0b6a9f1346736646d08ab94ae2ac
How to set the management interface on a SG300 Switch in Layer 3 mode? I've some vlans configured on the switch with interfaces in each of them:
Vlan 100 (10.0.1.254 /24)
Vlan 200 (10.0.2.254 /24)
Vlan 300 (10.0.3.254 /24)
...
Vlan 900 (10.0.9.254 /24)
Now, the management interface is listening on all interfaces (IPs). But I would like to configure the switch to only listen on 10.0.9.254. What I need to configure or whether it is possible?
My ISP insists that in order for me to have a home network use their router/modem ("2-Wire") for internet access, I must make my own network router act as a bridge since their modem is acting as the router. I.e. she said put your router into bridge mode. I don't know how to do that and Linksys won't offer assistance.
View 6 Replies View RelatedI have a WAG54G2 working fine for more than 2 years now. It has the initial firmware version 1.00.10
Recently I mode it from my home to my store, where I have a already working CCTV setup. Initially the router did not work, but once the service provider removed the mac-id binding (with my previous ADSL2+ router) the WAG54G2 was connecting on DSL. However it never got a DNS value. Currently I am using it with a fixed DNS.
After a few days of working I noticed that my remote viewing for the CCTV was not working. On checking the router settings I saw that the router had defaulted to no settings at all. Changing it back to PPPoE did not work since the page would not render completely. Resetting to Factory settings also did not work. However simply switching off the router and restarting it worked. I let it go then. The same thing happened again within a day or two. Each time restarted the router seemed to solve the problem, however temporarily.
I have the SPI firewall enabled also I have application port forwarding set for HTML port 80 forwarding to say port 1234.
I'm working with a customer who has an SGE2000P and a Catalyst 2960 to setup and configure a single mode fiber link. The SGE2000P has an MFELX1 fiber GBIC and the 2960 has a GLC-LH-SMD GBIC. When I have the customer plug in his fiber, there is a power light that comes on on the MFELX1 GBIC. Neither GBICs/switches show that a link or activity is occurring, but the presence of that light makes me think that they are connecting somehow. Are these two switches/GBICs compatible?
View 1 Replies View RelatedI have a stack of 8 3750x switches connected via Stackwise. In addition, I have these switches configured as two Powerstacks. When I look at the Powerstacks, they are showing as being in power-sharing mode. When I look at the individual switches, they show as standalone. Right now, I have 1 switch in each powerstack that has two power supplies, and then the other three have a single power supply. Below is the output for "Show stack-power detail" as well as the Powerstack configurations.
Power Stack Stack Stack Total Rsvd Alloc Unused Num NumName Mode Topolgy Pwr(W) Pwr(W) Pwr(W) Pwr(W) SW PS-------------------- ------ ------- ------ ------ ------ ------ --- ---Powerstack_1 SP-PS Ring 2145 45 570 1530 3 3Powerstack_2 SP-PS Ring 2860 60 760 2040 4 4Powerstack_1-1 SP-PS Stndaln 1430 520 190 720 1 2
Power stack name: Powerstack_1 Stack mode: Power sharing Stack topology: Ring Switch 4: Power budget: 700 Power allocated: 190 Low port priority value: 20 High port
[code].....
I'm looking for switches that support single mode fiber connections and would like to know if "WS-C3750-FS-S Catalyst 3750 24 100BaseFX + 2 SFP" and "WS-C3750G-12S-S Catalyst 3750 12 SFP" can serve the purpose?
View 6 Replies View RelatedPrior we only had 62.5u multi mode.I've got 3750x switches and new SM SFP and yellow fiber patch cables. None of my links show connected. No lights and trunk port interfaces show down/down.
Is there a special command you have to do on a port when using SM fiber? Do you think I need cross over fibers?
Also, should I be able to see a laser signal light like MM or is SM a different frequency so it's not as visible as MM?
I faced with a strange behavior of ME3600.For testing purposes I linked Cat3550 and ME3600 switches via trunk mode. All interfaces are in Up state. But I couldn't ping SVI200 of Cat switch from ME3600 and vice versa. [cde]
This scheme perfectly works with another L3 swithes. For example Catalist3750. I know that ME doesn't support VTP, DTP and so on. Also, I've tried latest software.