Cisco Switches :: Virtual NIC On VOIP System And SG500X?

Aug 27, 2012

We have a VOIP system with 1 physical NIC attached to our SG500X. It has a virtual MAC address along with the physical MAC address. It has 2 IP addresses tied to it.
 
I can ping the physical IP address, but can only ping the virtual address from the same vlan as the virtual nic. However, if I clear the arp table, a few pings will go through until they all time out again. This is causing problems on my phone system, and I need to establish this communication. I have tried putting in static MAC and ARP entries, but that does not work.

View 23 Replies


ADVERTISEMENT

Cisco Switches :: Connecting SG500x-24 To MOE

Jan 2, 2013

Trying to connect SG500X-24 switches to a new installation of MOE (four sites)provided by Century Link.  I have tagged the uplink port with the MOE vlan, but traffic does not want to pass through.

View 1 Replies View Related

Cisco Switches :: Unable To Connect To SG500x

May 20, 2013

We have problems with MGBSX1 when connect to SG500X switches , need configuration adittional ?? or only plug and play ?

The SFP-10G-LRM= is compatible for connect between WS-C2960S-24TD-L with SG500X ?? 

View 1 Replies View Related

Cisco Switches :: SG500X-48-K9-G5 And SG200-18 Compatible SFP

Jun 24, 2012

I am interesting if GLC-SX-MM sfp modules are compatible with following switches: SG500X-48-K9-G5 and SG200-18.

View 7 Replies View Related

Cisco :: WS-C6509-E OID For Virtual Switching System

Nov 21, 2011

The OID I am using  for module index 6509-E family is not working on 6509 Virtual Switching System(VSS).I have used "1.3.6.1.4.1.9.5.1.3.1.1.1" for single6509- E configuration. How to know OID for module index on VSS environment.

View 5 Replies View Related

Cisco Switches :: How Many Queues Actually Supports Switch SG500X

Nov 11, 2012

I need to confirm how many queues actually supports the switch SG500X?. In SG500X_data_sheet.pdf document (pg. 8) say they have 4 hardware queues (8 future) !

View 2 Replies View Related

Cisco Switches :: SG500X-58 - Native Stacking Mode?

Mar 15, 2013

The switch SG500X-48 has 4 SFP+ ( 10G ) ports - XG1, XG2, XG3/S1, XG4/S2 - and two configuration modes - standalone and "native stacking".
 
Can I use XG1 and XG2 SFP+ ports to connect servers when "Native stacking" mode is active ?

View 1 Replies View Related

Cisco Switches :: SG500x How Many 10GE Ports Can Be Used For Uplink

Apr 25, 2013

i was checking the datasheet of 500X series and got confused regarding the 10GE uplinks. how many 10GE ports can be used for uplink and which transceiver should be used for 10GE copper uplink? for example, SG500x-24 switch has 24GE ports and 4x10GE uplinks. can i use the 4x10GE ports for uplinks or only 2 ports are for uplink and the rest for stacking?

View 6 Replies View Related

Cisco Switches :: SG500x Stack And Connect To A NAS Device At 10G

Oct 11, 2012

I purchased 2 SG500x switches that I will stack and connect to a NAS device at 10G. I need to purchase transceivers. The documentation has me confused. I just want to make sure that I can use SFP-10G-SR to stack and as the interface to the NAS. S1/S2 for stacking and XG1/XG2 to connect to the NAS all at 10G.                  

View 1 Replies View Related

Network Layout For IP Camera VoIP System?

Mar 31, 2011

Alright, first off a little background. Im recent IT graduate (last spring) but not yet working in the field in any official capacitance. Its been about a year and half since I had my last Cisco class. Right now Im in the beginning process to work with locally own retailer setup a network infrastructure for IP camera and in the future VoIP, about 45 50 total IP devices when the project is complete.Nothing has been purchased yet but I have some candidates and a network layout planned, thought this is the first time Ie setup network of this type in the real world.Right now I looking at Netgear and LG/Ericsson (previously SMC, Nortel) switchesHavent gotten to the router yet and VoIP will come later.For either brand there would be one 1000MB 24 port switch and three 100MB switches, all of them 24 port and all will have PoE on all ports.[CODE]

View 4 Replies View Related

Cisco Switches :: SG500X-48 Stack Link Down Warning Messages?

Jan 24, 2013

I just deployed two stacked SG500X switches.  I noticed these messages in the log (see below).  Despite these messages everything appears to be functioning.   
 
21474818342013-Jan-25 11:41:17Warning%Stack-W-LINK DOWN: link 0 on unit-2, aggregated (369)      
21474818352013-Jan-25 11:41:17Informational%Stack-I-LINK UP: link 0 on unit-2, aggregated (369) 
21474818362013-Jan-25 11:37:25Warning%STCK SYSL-W-UNITMSG: UNIT ID 2,Msg:%Stack-W-LINK DOWN: link 0 on unit-2, aggregated (1) 
21474818372013-Jan-25 11:37:25Warning%Stack-W-LINK DOWN: link 0 on unit-2
21474818382013-Jan-25 11:37:25Informational%Stack-I-LINK UP: link 0 on unit-2 
[Code]....

View 1 Replies View Related

Cisco Switches :: Does SG500X Support Redundant Power Supply

Jun 1, 2013

Does SG500X support the following
 
redundant Power Supply?PIM sparse mode (PIM-SM), PIM dense mode (PIM-DM), and PIM sparse-dense mode?Layer 4 prioritization: enables prioritization based on TCP/UDP port numbersUni-Directional Link Detection (UDLD) — monitors a link between two switches and blocks the ports on both ends of the link if the link goes down at any point between the two devices 

View 2 Replies View Related

Cisco Switches :: SG500X XG Ports Show Unknown Speed

Oct 30, 2012

We currently have the XG1 through XG4 ports on our SG500X switch setup in a LAG with the Cisco 10G-FiberOptics.  Everything is working fine,however in the web UI under Port Management->Port Settings the "Port Speed" is listed as Unknown.  All other ports report the speed correctly. We have 2 SG500X switches configured this way and both are reporting the same Uknown speed. 
 
Firmware Version (Active Image):  1.2.7.76  Firmware Version (Non-active):  1.2.0.97

View 1 Replies View Related

Cisco Switches :: 1G Fiber Module Part Code For SG500X

May 10, 2012

We Need SG500X Switch for its VRRP Features.  and also, We do have 1G Fiber on Network.  So, which fiber module can i choose for SG500X switch.
 
It do have 4x 10GE SFP+ Ports.
 
Can i choose MGBLX1  for SG500X for 1 gigabit fiber connectivity?

View 3 Replies View Related

Cisco Switches :: SG500X-24 Stacking - Keeping Connections Active

May 12, 2013

I am installing a network that has two SG500X-24 switches as core and several SG300-52 switches as access switches. I've seen in the SG500X-24 datasheet that there is a True Stacking feature. But in the data sheet there are not a lot of details about it. My doubt is the following. If I configure the two SG500X-24 switches as a single switch through stacking them, can I connect one SG300-52 switch to these two SG500X-24 switches through two cables (both configured as a LAG in the SG300-52 and in the SG500X-24 stack, one cable per SG500X-24), the  the first cable connected to the first SG500X-24 switch and the second cable connected to the second SG500X-24 switch and keep both connections active?

View 3 Replies View Related

Cisco Switches :: SG500X 10Gb Copper To Server Hardware

Feb 7, 2013

We have a site with a number of SG500X switches who are about to have a new server installed.
 
The server is a Dell ESXi host with a dual port 10Gb NIC supporting SFP+.
 
I know the primary purpose of the 10Gb ports on the SG500X is for stacking etc. but the switch does come with four 10Gb ports.
 
Why I wouldn't be able to utilize a 10Gb port as a copper connection to the 10Gb NIC on the server? Anyone out there with a SG500X connected directly to a server at 10Gb?

View 1 Replies View Related

Linksys Wired Router :: How To Set Up RVS4000 QOS Settings To Work With VOIP Phone System

Dec 15, 2011

How to set up RVS4000 QOS settings to work with a VOIP phone system?  I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection. 

View 1 Replies View Related

Cisco Switches :: SG500x Point To Point Connection Very Slow After 1.30.59 Update

May 1, 2013

I have a point to point 100mb line connecting SG500x switches at 2 locations, with these ports in a vlan together. I use layer 3 on the SG500x's to route between the two sites. I also have RIP protocol enabled to allow for automatic failover if the point to point fails (this works well).
 
I upgraded the ios to 1.30.59, and the connection now runs at a fraction of the speed. I have hard-coded the ports to run at 100mb full duplex, but I still only get around 12mb of throughput between the switches. I used to get about 90mb before. The provider also hard-coded the circuit to 100mb full duplex. The provider has checked the circuit remotely, and everything looks fine. I tested with a laptop at each side, and did get almost 70mb throughput. I would think this indicates some type of setting mismatch, but i cannot find anything.
 
I am using a backup vpn for now as some things look flaky as well (on vpn, I can use the web interface to access the SG500x on the opposite side, but on the point to point I cannot - I can ping the device though).
 
I have seen some references on here to shutting off STP on these 2 ports.

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst WS-C3750G-48TS-E - Virtual Switching System

Sep 10, 2012

I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?

View 3 Replies View Related

Cisco Switches :: SGE2000p QoS For VoIP?

Dec 27, 2012

I am trying to get QoS for my VoIP system setup on several SGE2000p switches and have got a question...How do I define the ACL for RTP? As far as I can tell it will not let me enter a UDP port range for the RTP traffic... And I cant imagine creating rules for each port would be very effective either. So, how can I define an ACL to cover the RTP traffic so I can classify it?

View 4 Replies View Related

Cisco Switches :: Implementing VoIP With SG300-28P

Oct 12, 2012

I want to implement VoIP on my client network, currently the data network is using SG300-28P small business switches for user access. According to my design the IP Phones (Cisco 9971 and 7942G IP Phones) are to connect to the small business access switches while the user PCs connects to the IP Phones.
 
My concern is I really don't understand how the small busness switches will advertise the voice VLAN to the IP Phones. I understand that the switches are suppouse to use LLDP/CDP for this but it seems the model I have can only do LLDP. The IP Phones and the PCs connected to them will be recieving IP addresses from an uplink L3 managed switch.
 
how LLDP works (particularly regarding this scenario)? Does it matter if the small business switch is in L2 or L3 mode for the VoIP implementation?

View 4 Replies View Related

Cisco Switches :: Sge2010p (v5) - How To Set QoS For VoIP Vlan

Jul 24, 2011

I have configured 2 Vlans on the network. 1 - native Untagged for data traffic and 100 Tagged for VoIP.I have 4 SGE2010p switches 2- of them in stack working in L3 mode and 2 connected to the stack via single ethernet links in L2 mode.I have IP phones with trunked ports -Vlan100 tagged and 1 untagged. I have set CoS 5 for Voice Vlan 100 on the phones and CoS 5 to queue 3 mapping (in basic mode) on all switches.But it seems to not work at all.Should I use Advanced QoS mode?Where Can I find some QoS configuration example for Voice Vlan on SGE2010p switches?

View 1 Replies View Related

Cisco Switches :: SGE2010P - VLan For VOIP?

Mar 11, 2012

I just purchased two Cisco switches (SGE2010P) for the new Mitel 5000 Phone System. The Mitel vendor programmed and setup the phone system for us, but they couldn’t figure out the VLAN setup on the my switch. So now I have everything on one network and I am stuck on my own to figure the VLAN on my own. So please, some step by step on the settings on the switches, the router and the server (DHCP).

Here is what I have now:
2 floors building with a Cisco SGE2010P switch for each floor.Sonicwall TZ 210 routerWindows 2008 R2 server for DHCPMitel 5000I have the switch on Layer 2 at this moment, but I can switch it to Layer 3 if that makes the process easier and less steps.My network as follows: Router: 192.168.123.254Windows Server: 192.168.123.9Switches: 192.168.123.5 and 192.168.123.6Mitel 5000 server: 192.168.123.7 (has to be changed)The PCs are connected to the phones.

View 5 Replies View Related

Cisco Switches :: Setting Up SLM248GT-NA Switch For VoIP?

Feb 12, 2013

We have a Cisco slm248gt-na smart switch in our office that I am trying to configure to support and optimize for VoIP. We have desktops hooked up off the phones in most cases. Are there any config guidelines to optimize the switch so it has proper QOS set and VoIP gets higher priority over data.

View 4 Replies View Related

Cisco Switches :: Configuring ESW-520-48P For VoIP / Ring Central

Apr 26, 2011

I am looking for a Best Practices or a few places to pay attention to in the Cisco ESW-520-48P switch I have. My VoIP solution is RingCentral, and while they are Cisco phones, I've been hestitant to setup VLANs etc. the way I am used to. Plus setting up Auto QoS seems different than what I am used to with a 3750 switch.
 
Right now I've left the Smartports Wizard alone, and none of the ports are configured. There are no VLANs or QoS on the LAN currently.
 
What I was running into were calls cutting out where one side wouldn't hear the other anymore, but the call would remain connected. However, this has happened in this small 15 person office, when there is only one employee here after hours, talking on the phone. There isn't any heavy network traffic, because I have network monitoring showing me low usage (no streaming music, videos, or anything else).
 
This switch has a Gb connection to a Linksys SR2024 (the server switch), which is also set at Factory Defaults. I mention that because I recently bypassed the ESW-520-48P, and plugged one phone into that switch and the RingCentral phone worked fine for outside calls.
 
Is there something besides QoS that I should look at in the ESW-520 switch that might be causing a checkpoint of some sort, or interrupting VoIP traffic that I need to configure or disable?
 
And are there any Best Practices or scenario guides for this switch? I found the Admin Guide, but it really just explains every option in the GUI for the switch. And it seems all of my CCNA training isn't working with going in and quickly troubleshooting this switch besides knowing that something in it could be hanging it up.

View 6 Replies View Related

Cisco Switches :: SF300 24p And VLan For VoIP Traffic?

Jan 2, 2012

I have a SF300 24 P and Iam trying to configure a voice vlan this is what I have done so far and it doesnt work.
 
1. create vlan 30 for voice traffic and enable it

2. Telephony OUI add my mac address for allworx phones

3. Port to VLAN add 30 has tagged, port to vlan 1 untagged

4. Vlan to port I try to add 30 and get this error (Port e15 is candidate in voice Vlan 30 and cant be configured as static member in the vlan.

5. Under Discovery LLDP, LLDP MED port  Setting Enable MED status, then all other options to yes
 
In my LLDP neighbor  information all my phones are there and says under port ID 0 ( my phones support LLDP and CDP)

View 1 Replies View Related

Cisco Switches :: ESW-520-24P - VoIP Packet Loss Every 35 Seconds

Apr 14, 2013

We have a customer running a Asterisk based Phone system, using Snom 320 phones and a ESW-520-24P as their switch.
 
Recently we have been confronted with an issue where every 35 seconds their is a very obvious drop of audio for both parties of a call.  We know it is not the phone system as we have run tests directly over the BT copper lines that have no drops what so ever.  Unfrotunately when we introduce the LAN in any way, we get the drops every 35 seconds.
 
We are running the whole solution on 1 vlan, yes I know probably better to use two, but the Cisco cannot automatically detect the Snom 320 phones to swap it to another VLAN, which complicates using a VLAN setup.
 
I really need to work out how to stop these packet drops, but I am new to the world of Cisco and dont really know where to look or what to try.

View 1 Replies View Related

Cisco Switches :: SG500 Possibility To Bind ACL To A Virtual Interface

Mar 24, 2013

I have a switch from SG 500 Series the works as Layer 3 Routing Switch with the Firmeware 1.2.7.76. I have create some diferent VLAN´s and have defined one ACL for each VLAN. Now i try to do a binding from the ACl to a VLAN but i have only the option to bind the ACL to a phys. Interface or  a LAG.is the a possibility to bind the ACL to a virtual interface like in other Cisco serieses and how it works ? the Backround is i have connectetd 2 Hyper-V Server where the Guests are in different VLAN´s and the server is connectetd with a 10Gb Trunk to the Switch now the switch routed the different VLAN´s and i must have some restrictions between the VLAN´s.

View 2 Replies View Related

Routers / Switches :: Manage Static IPS In VOIP Setup?

Jul 21, 2011

I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:

67.xx.xxx.153, through .158My subnetmask is set to:

255.255.255.248My Settings:

The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.

On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.

For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?

View 7 Replies View Related

Cisco Switches :: QoS Setup On SGE2010 To Support VoIP Trunks Between PBXs

Aug 28, 2012

how to configure QoS on my SGE2010 to support my Toshiba CIX PBX VoIP trunks.  The infrastructure is straight forward: PBX(1)<==>SGE2010(1)<==>SGE2010(2)<==>SGE2010(3)<==>PBX(2) where PBX(1) and PBX(2) are connected through three SGE2010's that are trunked via fiber between buildings.  I don't have VoIP handsets and the PBX's are on their own VLAN.  Everything else has been a breeze in these switches but I have no experience with QoS

View 6 Replies View Related

Routers / Switches :: Office VOIP With Multiple Private Networks?

Jan 23, 2011

I'm going to move offices into a shared situation with 3 companies. Each company will want its own private network so there's no snooping between companies. I am planning on using VOIP for the phone system (Nextiva cloud based). Is it possible to set up the system so that each company has access to the VOIP system but yet remains sequestered in the their own network for everything else. I was hoping to do this with one data port at each workstation using Cisco SPA-303 phones. The way I understand this, is that the phone plugs in to the data port and you daisy chain the workstation off from each phone. Is this possible to do this while having the system I described? Another wrinkle is that I'd also like all the networks to be access shared printers.

View 7 Replies View Related

Cisco Switches :: SG200-50 VLAN For VoIP Phones Connected To SRP541W Router

Apr 15, 2013

I am new to VLANs although I generally understand the concept.  I have a small office with 25 desktop/laptops and 15 VoIP phones connected with a SG200-50 switch and on Port 1 I have the Cisco SRP541W router for DHCP and Internet access.  My goal is simple: 1) Segregate the VoIP phones (voice) from the computers (data) and 2) Prioritize the VoIP phones traffic.
 
I believe this can be accomplished by setting up a second VLAN and maybe a third (if the default should not be used) and then identifying those ports as Voice VLAN ports.  I guess I just need to know how to flag each interface and each port so that they all can talk to the router on Port 1 yet the voice and data will be in different broadcast domains.  Also, do I need a management VLAN??
 
Is this setup correct? VLAN 1 - default (data) Port 1 (Trunk) (Tagged)Port 2 - 30 (Access) (Untagged)VLAN 2 - voice Port 1 (Trunk) (Tagged)Port 31 - 48 (Access) (Untagged) What should the interface settings be on each port (General, Access or Trunk)? What should the port VLAN membership be on each port (Tagged or Untagged)??

View 4 Replies View Related

Cisco Switches :: Sg200-08 No System Led?

Aug 30, 2011

I have a new sg200-08 smart swith. I cant git it to work (No link) on the NIC.
 
I have tested:
Different cables cat5-6
Different ports 1-8
4
different computers
 
When i power on the sitch the only led who lights up is port 1, no system led.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved