Cisco Switches :: Pinouts For Making Serial Cable To Connect From PC To Linksys SPS224G4?
Oct 16, 2011Pinouts for making a serial cable to connect from a pc to the LINKSYS SPS224G4 Switch?
View 1 Replies
ADVERTISEMENT
Cisco Switches :: Linksys SPS224G4 Throughput Causes Slowness
Dec 18, 2012during using switches Linksys sps224g4 faced with the following problem.
When the end user is connected in 100 Mbps port of the switch and rtt more than 10 ms to a remote server, the download speed from server in one stream does not exceed 2.5 MBWhen rtt less than 5 ms, the download speed in the one stream 11 MB.
When switching user from 100Mbps to 1Gbps port, download speed from remote server grows up to 11-14 MB.When we connect user to 100Mbps port of another manufacturer switch in one stream download speed reaches 10MB.
Tried to configure next parametrs:
1. Checked for firmware 1.0.2 and 1.0.6, the situation is identical.
2. Enable, disable negotiation on the client port.
3. Turn on / off qos.
4. Turn on / off flow-control.
5. Turn on / off jambo-frame (I do not know how it could have an influence, just in case).
6. During traffic analizing on the users port were found no differences between downloading from servers with rtt 5 and 35 ms.
Cisco Switches :: How To Enable LLDP In SPS224G4
Mar 8, 2010I am trying to enable LLDP in sps224g4 switch. console# sh verSW version 1.0.2 ( date 18-Nov-2008 time 12:38:16 )Boot version 1.0.2 ( date 13-Nov-2007 time 14:11:51 )HW version 00.03.00 While there is snmp lldp oids, and I can snmpwalk and snmpset them, no matter what I do switch neither send nor recieves LLDP TLVs, and all LLDP related fields for ports stays at 0 LLDP packets send/recieved or empty.
View 7 Replies View RelatedMaking Time Warner Cable To Use A Pre-existing Cable Line?
May 29, 2012Is it possible for Time Warner Cable to use a pre-existing cable line which is going into my cable box to hook up a modem so I can have Internet? I've got a modem in another room but I don't want a cable running down my hallway for 30 feet.
View 6 Replies View RelatedLinksys Wireless Router :: Serial Connector Adapter / Cable For WAN RJ-45 Port?
Aug 21, 2009On the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find?
View 9 Replies View RelatedCisco Switches :: Linksys SRW2016 Switch Serial Console Not Working
Jan 5, 2011I have had the switch for about 2 years and recently moved. The manual specifies:
38400 bps and 8-n-1 serial port settings using DB9F to DB9F cable.
I have done this and tried using multiple machines/ports/cables as well as several peices of software (minicom, PuTTy, hyperterminal) and none give me any output from the switch at all.
The trouble is that in its original config, it had 1 port locked into its own VLAN for management with port security and an obscure RFC1918 IP address which I cannot recall for the life of me.
At this point, I have no access to TCP/IP management so serial console is my last hope and is not working.
Cisco Switches :: What Kind Of Cable Is Required To Connect To Console On Linksys SRW2024
Apr 26, 2011What kind of cable is required to connect to the Console on a Linksys SRW2024 switch ? ( I've lost the original cable )I use the following settings: Speed 38400, 8 bits, no parity, no flow control and stop bits 1I have tried a serial cable, no go.I have tried a null modem cable with partial handshaking, no go.I have tried a null modem cable with full handshaking, no go.For the null modem cables, if I use it to connect between computers using hyperterminal it works very well. What I type on one computer appears on the other computer's screen.However, I can't get anything out of the switch. I've tried pressing Enter repeatedly, resetting the switch with the Console cable on, etc.
View 2 Replies View RelatedUSB To Serial Cable Recommendation?
Nov 23, 2011I think the crappy usb to serial cable from china broke because when i boot up my cisco router, after it decompose the IOS image and shows all the interface links, it won't do anything. I can't get to user exec mode.anyways, i think my usb to serial cable is faultily. I got one that is from ebay for like 2 bucks and i think it is the reason why i can't even connect to my router now
View 3 Replies View RelatedCisco Switches :: SG300-10P / Making Vlan For All Wireless Devices On Network?
Feb 18, 2012We connected 4 wireless access points (AP541N-E-K9) to an SG300-10P switch.We want to be sure that no wireless clients can alter settings to the network by connecting to any of the networking devices. We also want that no wireless devices (except a few) can connect to computers that are on the wired network. I'm new to configuring networking devices so how to set up the switch for this.We already added all the MAC-adresses of all the wireless devices (that are allowed to use the wireless network) to the access points.
View 3 Replies View RelatedCisco WAN :: 3560V2 Using Console Cable Attached To USB To Serial Adapter
May 9, 2012I am having issue consoling into Cisco 3560V2 using console cable attached to USB to serial adapter.using putty.when i try to login on the putty i only see black screen.
View 5 Replies View RelatedRouters / Switches :: Connect Through The Cable Tv Network?
Jan 22, 2011I am wondering what the cable wires or sockets on the back of this router are for? could it be you can connect through the cable tv network the sockets fit perfectly in the back of the router thats a strange coinsidence dont you think?
View 2 Replies View RelatedCisco WAN :: 3750 Layer3 Switches - Connect Them Via Stack Cable
Jul 11, 2012I have two 3750 layer3 switches and I need to connect them via stack cable.so if I connect them with the stack they will be act as an one switch, but for the configuration if I create a VLANs on the master switch (applied all the configuration on the master one) this configuration will be transfered to the slave one or I have to repeat the configuration that I did on the master.
View 5 Replies View RelatedUnable To Connect Two D-link 24 Port Switches Through Cat 6 Cable?
Aug 9, 2012I am trying to connect two D-link 24 port switches thru cat 6 cable, distance is less than 50 meters, but its not working but if i connecting it with a Laptop i am able to connect to the network. But if i connect the switch in between it fails i tried changing the switch and cable but no use anyone have a clue how it fails?
View 4 Replies View RelatedCisco Switches :: Lost Original Console Cable To Linksys SRW2048
Feb 24, 2013I have lost the original console cable to the Cisco Linksys SRW2048 and was wondering if I can use the Cisco console cable or can a regular serial cable with female ends will work?
View 2 Replies View RelatedLinksys Cable / DSL :: WAG54G2 Switches To Bridged Mode Every Few Hours?
Jun 28, 2012I have a WAG54G2 working fine for more than 2 years now. It has the initial firmware version 1.00.10
Recently I mode it from my home to my store, where I have a already working CCTV setup. Initially the router did not work, but once the service provider removed the mac-id binding (with my previous ADSL2+ router) the WAG54G2 was connecting on DSL. However it never got a DNS value. Currently I am using it with a fixed DNS.
After a few days of working I noticed that my remote viewing for the CCTV was not working. On checking the router settings I saw that the router had defaulted to no settings at all. Changing it back to PPPoE did not work since the page would not render completely. Resetting to Factory settings also did not work. However simply switching off the router and restarting it worked. I let it go then. The same thing happened again within a day or two. Each time restarted the router seemed to solve the problem, however temporarily.
I have the SPI firewall enabled also I have application port forwarding set for HTML port 80 forwarding to say port 1234.
Cabling / Cards :: Connect To Cisco Console With / Without PC Serial Port?
Jan 5, 2012I need to connect to the console port on a cisco firewall, an rj-45 connector. The cable is a rj-45 at one end and a serial on the other. My PC has no serial port and I am unable to use the provided cable to connect to the firewall appliance. Is there software that can allow serial over my PC's Ethernet? I really don't have time to order a serial card for my PC.
View 1 Replies View RelatedWindows 7 - Connect Virtual Machine To Host Via IEEE1394 / USB Or Serial Port
May 15, 2013I have a host machine (Laptop, Win 7 Home Premium x64) running Windows 7 Ultimate x64 on VMWare Workstation 9. I've got this system set up for UMDF driver development, because I need a target machine to debug drivers on. However, because I'm developing drivers for Win 7 (x86 and x64), I cannot connect to the virtual machine on via a simple network connection. Connection methods are outlined here.
I have tried a few different pieces of software (mostly Eltima software), and have Google'd every combination of phrases that I can think of. I can't find any information on this anywhere. I don't just need to share data between the machines, I need a more "physical" connection.
Does any know how to do this, or if there's another (preferably more simple) way of doing it?
Linksys Cable / DSL :: WAG320N Cannot Connect ISP
Mar 6, 2012How to configure settings for router E4200I live in Finland and bought new Cisco Linksys WAG320n router modem as I am experienced Cisco user. However after spending several hours and setups on the WAG320n router I cannot get it to connect on the ISP ADSL line.
RFC2684 Bridged
LLC/SNAP
g.dmt or ADSL2+
VPI 0
VCI 100
But once I setup these or acutally any other setting I cannot get the router to connect. With the right settings I can get the DSL PVC status up and connected but the ModemRouter cannot connect and retrieve IP-address from ISP.
Linksys Cable / DSL :: X2000 Will Not Connect To ATT?
Jan 31, 2013Trying to replace old modem with the X2000 but it will not connect to the internet, my provider is ATT DSL.
View 2 Replies View RelatedLinksys Cable / DSL :: Cannot Get X2000 To Connect To ISP
Oct 14, 2011I cannot get my X2000 to connect to my ISP in the UK. From what I've read elsewhere I'm not the only one but I need to determine whether this is a router support issue or ISP.
View 9 Replies View RelatedLinksys Wireless Router :: WRT54G - Not Connecting To Laptop While Making Network Secure Laptop
Sep 5, 2008I have a linksys system WRT54G at home. I had no problems with the Linksys router until about a month ago when I decided to make it a secure network. I run three computers of the wireless router (1 desktp and 2 laptops) Since making the wireless network secure I can not connect with my business laptop IBM Thinkpad X40, but thother e computers work just fine.
View 8 Replies View RelatedLinksys Cable / DSL :: Some Devices Can't Connect To X2000
May 25, 2012I have been setting up my new Cisco X2000 wireless router recently and I have it working fine for my desktop/laptops and even the PS3, however for some reason when you try to use the wireless on some of the other computers in my house it doesn't work unless you are using a wireless guest account.
View 2 Replies View RelatedLinksys Cable / DSL :: WAG160N Won't Connect To Internet
Mar 7, 2011WAG160N
S/N: SSH00H406302
MAC: 001D7EB42921
Manufactured 04/2008
I can no longer access the internet, and the internet has been difficult to bring up for one to two weeks.Internet light does not come on. Under Status tab, interface is down, tried refresh and connect but nothing.The IP address can be pinged, 4 packets sent and 4 packets received. Tried resetting defaults and refreshing but no success.Bought this router in September 2008 to replace WAG54G which was constantly turning on and off every few seconds.
Linksys Cable / DSL :: E1550 Cannot Connect Via Dsl Modem
Oct 2, 2011Have an existing befsr41 / westell b90-210015 connection that has been working for years... replaced the befsr41 with a e1550 and cannot connect to the internet. Tried to connect to the modem directly to see how to put into 'bridge mode' but cannot find the right ip address.
View 1 Replies View RelatedLinksys Cable / DSL :: X3000 Cannot Connect To ADSL
Dec 12, 2011I just bought a Linksys X3000 to work with my ADSL connection (provider is Singtel from Singapore). I managed to use Cisco connection application to logon and setup the router OK, yesterday. I even connected my PC to the router by LAN, and also a few devices wirelessly.At the end of the day, I switched off everything... but next morning, when I booted up the router, I found that all my devices cannot access internet. Upon checking the server (192.168.1.1), I found that it does not have a IP from Singtel, although on the router the internet symbol (globe sign) is lighted up.I rebooted the router twice, getting the same results (note: I waited for a long time each time, until the globe was lighted up).I disconnected the X3000, and reconnected my Netgear DGN2000. It worked (and retrieved an IP address from Singtel). I then disconnected the Netgear and reconnected X3000. To my surprise, this time X3000 got the IP address and then internet is working again.
View 9 Replies View RelatedLinksys Cable / DSL :: WAG200G Won't Connect To Internet?
Feb 21, 2011Tried connecting my laptop...internet doesnt work. Tried doing restarts and stuff nothing seems to work.
View 1 Replies View RelatedLinksys Cable / DSL :: VPN Failing To Connect With WAG54G2
May 28, 2012I need to use VPN from home to connect to my company. Company IT say that they can see my connection is successful but from home end it appears to fail (timeout). I'm using a CISCO WAG54G2 router. After attempting VPN access I have to re-boot router to establish broadband connection. I have checked Plusnet (ISP) firewall settings as okay (LOW). I have found two CISCO links which describe a similar(?) issue:
[URL]
I reviewed my router's Single Port Forwarding parameter settings in light of info in these links. I then added three new ones: VPN, VPN1, and VPN2 VPN; Internal Port:500; External Port 500; Protocol:UDP; IP:192.168.1.47; Enabled Yes VPN1; Internal Port:4500; External Port 4500; Protocol:UDP; IP:192.168.1.50; Enabled Yes VPN2; Internal Port:10000; External Port 10000; Protocol:UDP; IP:192.168.1.51; Enabled Yes
These changes have not worked but I not yet removed them. My company uses 'Delta VPN' product. No other changes to parameters have been made before or after.
Linksys Cable / DSL :: WAG160N - Cannot Connect To IP Address
Aug 10, 2012I have a WAG160N wireless router that I want to use to repeat a wireless signal that is delivered by our ISP who installed broadband in our cottage, not our house (long story, we live rurally, so I won’t get into it).
So I understand I can simply plug my Linksys to power and that will pick up the signal inside our house (which it does, and we get an excellent strength signal).I further understand that I have to configure the Linksys so it talks to the modem provided by the ISP and which is about 50 metres awayFrom the Cisco website and my own docs I know the first step is to search the IP address online [url].,..
Linksys Cable / DSL :: WAG320N - Ubuntu Can't Connect To NAS And Other LAN PCs
Apr 23, 2011I have 2 PCs, an Acer H340 and a network printer wired to the WAG320N; two other PCs are connected wireless. On every PC I have Windows 7 and Ubuntu (except the NAS with WHS).When I boot with Ubuntu on every PC, I can print, I can connect to intenet, open the Web interface of the WAG320N at 192.168.1.1 but I CAN'T see the NAS and the other PCs: this with the wired PCs and the WiFi connected ones. A Galaxy Tab can browse the NAS content and the Web.I didn't had this problem with the modem router I had from the ADSL supplier and the Huawei D100 I used before.On the network map of the Cisco Network Magic the Linux PCs are showed connected to the WAG320N with a dotted line, when the W7 ones are connected with a solid line.
View 3 Replies View RelatedLinksys Cable / DSL :: WAG120n Cannot Connect To Internet
Nov 29, 2012I recently got a Linksys WAG120n wireless modem but I have a problem with its Wireless.whenever I want to connect to the wireless of the modem I have to reboot the modem. or I cannot connect to it or if I connect I do not have internet access the cable LAN interface of the modem is working is working properly.I used Mixed (b/g/n) as network mode and wpa2/psk as authentication mode with using preshared key.and the channel is 11. no matter if I enable MAC filtering for wireless or not it is just the same.my laptop is a HP G42 with a Ralink 3090 wireless card and I have installed the latest manufacturer driver of the wireless Card.but it is not working .even sometimes laptop cannot find the linksys modem until I reboot the modem.as I have found there is no newer firmwire on cisco site for this modem to upgrade.
View 1 Replies View RelatedLinksys Cable / DSL :: WAG320N - Cannot Connect Via PPoE
Jan 31, 2011I have a WAG320N and cannot get it to connect via PPoE.
i have IP, DNS etc but i cannot input the info manually
Linksys Cable / DSL :: WAG200g Connect To Another Router?
Oct 18, 2011I want to connect my wag 200g to another router. My other router have ip address 192.168.2.1 and is connected to my isp and my wag 200g is 192.168.1.254. What i want is to connect my wag 200g to the other router and to share the internet connection. I want also the dhcp server on the wag 200g to assign ip address to the wireless users connected on the wag 200g with ip addresses to the network 192.168.1.0.
View 2 Replies View RelatedLinksys Cable / DSL :: How To Connect Fiber Box To X3000
Apr 2, 2013 I have X3000 home gateway and very happy with this device. Use it now as ADSL modem/wifi router. Everything works fine but there is something I do not understand about this device.It has 4 LAN ports and a Cable port. Suppose, I am upgraing from a copper service to fibre. Fibre providers comes and installs their fibre box which is kind of a "modem" for fibre technology. how do I connect fibre box to X3000? Do I use Cable port or a LAN port?
As far as I understand the 4 LAN ports work as switch ports (work at OSI level 2, provide access strictly within same subnet, all devices connected to these ports share the same default gateway), and Cable port gets a different IP address via DHCP or another protocol from the fibre box, or directly from ISP (if we have PPPoE or IPoE service as an example). And there would be no point in plugging WAN link into a LAN port as X3000 would not be able to communicate to the gateway on the other end of the cable.
