I am having one Cisco ME 3400G-12CS switch with 4 NNI port & 12 UNI port.I want to convert all UNI port to NNI to as meet my client requirements.which Metro IP Access Image IOS version is required to convert those UNI port to NNI.
View 1 Replieswhere is the following CAT to IOS configuration for 6500 page moved? I am unable to find this utility? url...
View 2 Replies View Relatedcorrelates the older IOS format naming compared with the newer? I have an older catalyst 3550 that might need an IOS upgrade due to us starting to implement dot1x. The reason that I say this is that some of the commands in the dot1x config guide, such as aaa accounting dot1x, are not valid on this platform. The current IOS is c3550-i5q3l2-mz.121-8.EA1c but the newer format is the ipbase, ipservices, etc. format. There is a newer ios but how do I convert from one to the other? I think I need to research the IOS to see if the new commands are there as well as I want to make sure there are no gotchas from a hardware standpoint if I upgrade.
Cisco Internetwork Operating System Software IOS (tm) C3550 Software (C3550-I5Q3L2-M), Version 12.1(8)EA1c, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Fri 15-Feb-02 10:50 by antoninoImage text-base: 0x00003000, data-base: 0x006675E0
ROM: Bootstrap program is C3550 boot loader
ACSTMElab-3550 uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c3550-i5q3l2-mz.121-8.EA1c/c3550-i5q3l2-mz.121-8.EA1c.bin"
cisco WS-C3550-24 (PowerPC) processor (revision C0) with 65526K/8192K bytes of memory.Processor board ID CHK0615V0BPLast reset from warm-resetBridging software.Running Layer2/3 Switching Image
[code]....
We will be converting two 6500s to VSS. Each chassis has a Sup2T module, fwsm, 6908-10G blade, wism1 blades and two or three 6748-SFP blades. I was wondering how long the conversion process takes? If I remember correctly at the 2012 networkers lab it took maybe 10 minutes while using Sup720s. The instructor mentioned that with Sup2Ts it would convert a lot faster.
View 3 Replies View RelatedI have seen links out there for a conversion tool to convert commands on a Catalyst type switch (6509) to newer IOS type switches(4500-e) switches but they all error out on me on a 404. Any link where I can get this conversion tool?
View 1 Replies View Relatedconnecting a Cisco 3945 Router to an Ethernet WAN Link. The service provider has provided a 100M Ethernet Single Mode Fiber handoff to the customer premises with SC Connector. The CPE configuration proposed for this setup is like this. [code]
Since the SFP has LC Connector, i suppose i need to have an SC-LC Cable for connecting the Ethernet link. Do i need anything else, apart from above?
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
I'm trying to enable port security on several 4507R's. When I try to configure a range of ports the switch will randomly put 1 or 2 in err-disable. It's different every time I apply the config to the same group of ports. However if I do them one at a time it seems to work. But I really don't want to configure 6 fully populated switches one port at a time. We also have a lot of 3750's and they gave me no problem using a port range. [code]
View 4 Replies View RelatedWe just installed a hosted VOIP system using Cisco 7900 series IP phones. We are having a strange issue with a few computers where they pull DHCP information from our VOIP provider's DHCP server on the Internet and not our LAN DHCP server.
The switchports areconfigured as: switchport mode access
My rationale behind this is that the phones would use CDP to get their VLAN info from the providers Cisco router and the PCs would just ride on the default VLAN. But this is not the case. Computers randomly keep getting DHCP info from the provider's router. Do I have to use voice vlan x and make the switchports trunks?
I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
I have a 3750g connected to a "core" switch stack of 7 other 3750g's via 2 GigE ports in a trunk. This is currently in a switchport mode access port- channel so only the default vlan data is sent over. Now we have a need due to physical location of these switches, to allow vlan20 (DMZ) from this 3750g to the switch stack. I will configure a few ports on the switch stack for vlan20 and they need to be able to talk to the stand alone 3750g.To do this I will change the port channel on both endpoints to
-switchport trunk ecapsulation dot1q
-switchport mode dynamic desirable
also making the appropriate change on the interfaces belonging to this trunk.My question is, now that its a trunk port that carries multiple VLANs, how much is the bandwidth reduced on that 2gbps link?I have a very active VLAN (10) on the stand alone switch, but on the core I'm not going to be assigning VLAN 10 to any ports. So does traffic from VLAN10 even come across the trunk (wasting bandwidth) if no ports on the core side are assigned to it? I really just need vlan 1 and 20 (for now).
is it possible to shutdown a specific port on my 3750x and monitor this port at the same time .for example , im dealing with a mac authenticated network using port security , i want to shut down all the ports that are not used at the moment , however , if some one gets connected to the one of the shutdown ports i want to know the mac address of the user or atleast to know that i have someone who is just plugged in to the one of the shutdowned ports .
View 4 Replies View RelatedI'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
I have Cisco 800 series (888w) with BRI-ISDN port. Is there any way to change the usage of ISDN port to normal RJ45 port?I want to use this SOHO router to sharing connection.
View 0 Replies View RelatedI was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View RelatedI am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
My company uses Cisco 891's in replacement of the 1811 where we would have DBU used via an external modem and a triggered time of 3 minutes after a primary connection failure was identified. In testing the 891 in a Layer 2 failure environment, it is within milliseconds that the v.92 port is engaging after the layer 2 failure. Has anyone been able to get it to attempt at a more than millisecond rate?
Redacted config from router:
ip sla 1
icmp-echo <%= probeIP1 %> source-interface GigabitEthernet0
[Code].....
I currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 10 Replies View RelatedWas wondering how to set port security on the 881. I have all the FE ports shutdown except one and want to limit that port to one specific MAC address.
View 7 Replies View RelatedI have my Cisco 881 router up and running, routing all traffic on my small network. I am wanting to utilize port forwarding to enable FTP (forward port 21). All docs I have found say you need to be running Configuration Professional (not Express) to do this.
View 1 Replies View RelatedI have connected a Cisco switch ( SG 200-08) to a HP switch, everything works fine when have the HP port as untagged, but I can't get out when I tag the HP port. Maybe this is a HP problem but we can tag other ports on it to other switches.
Is it some setting on the Cisco switch i need to do? I have put 7 ports as access and one as trunk.
I have an problem with my new Cisco 876 Router. I configured port forwarding to access internal network devices from the internet . This works good from external but with my old Fritz box I was able to connect to this internal devices from the same internal network with the dyndns address.
So here is a short review for this:
DYNDNS Address port tcp 80 - > 192.168.0.80 tcp port 80
from ex tern it works but with source address example 192.168.0.20 to destination DYNDNS address tcp 80 (maps to 192.168.0.80 tcp 80 ) it doesn't work. Is there any trick in the config of cisco to let this scenario work?
I need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedHave 2 N2K with dual-connections to both 2 N5K, will all 4-ports of N5K will be the same port-channel. N2K as well ?
View 1 Replies View RelatedI have a Cisco 881 router in my office and I would like to do port forward for port 5060, and 10000 - 20000 to my PABX(192.168.1.61). After I did some research from internet, understand that we need to NAT by using following command to do port forward for port 5060. ip nat inside source static udp 192.168.1.61 5060 XXX.XXX.XXX.XXX(WAN IP) 5060 extendable However, now I'm facing an issue to perform port forward for a huge range of ports like 10000 to 20000.
View 9 Replies View RelatedI want to SSH into a Cisco 1841 router and depending on the suffix added to the SSH (i.e ssh myrouter.myroute.com 2002), would like it to forward this request to a terminal server.Can this be done? If so, how does one accomplish this? I have done something similar with RDP but I was not sure about SSH.
View 3 Replies View RelatedI've 8 Static IP assigned me from my ISP.
x.y.w.56 (not usable)x.y.w.57x.y.w.58x.y.w.59x.y.w.60x.y.w.61x.y.w.62x.y.w.63 (no usable)Subnet 255.255.255.248
I've a 877 Router and I would to:NAT al LAN Client with x.y.w.57Configure some ports ( i.e. 80 and 443) to be forewarded from x.y.w.57 to one LAN Server ( i.e. 192.168.0.1)Configure some ports ( i.e. 443) to be forewarded from x.y.w.58 to another LAN Server ( i.e. 192.168.0.2)
I have nx2000 boxes connected to nx7000 fiber module. There is a intermittent error occuring on nx7000 fiber module.
7000 fiber module drops down and all NX2000 boxes lose connectivity. When 7000 fiber module comes up, some equipment, not all, can not be reached through console port via network. These equipment are datacenter air conditioner console port, storage controller console port (iscsi controller interfaces run fine). It seems that handshake between these equipments and NX2000 ports are not fine.
I have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
This port is connected to nexus 5 k.
How does the IP address is assigned on management port of WS4507 R, syntax.
View 2 Replies View RelatedI have a stack of 4 3750 Switches.
1. WS-C3750G-12S
2. WS-C3750G-12S
3. WS-C3750X-48P
4. WS-C3750X-48P
The stack cable connected to Switch 1 Port 1 and Switch 4 Port 2 will not come back online. The logs show that there was a Stack line change. I have replaced the 1 meter Stack cable from Switch 1 to Switch 4 three times and it still does not come back online. This is the part that is interesting.. I have disconnected Port 1 Switch 4 and connected it to Port 2 Switch 4 and then Switch 4 came back online. This made me think Port 2 on Switch 4 was working correctly. Then I disconnected Port 2 Switch 1 and connected it to Port 1 Switch 1 and then Switch 1 came back online.