Looking to deploy N7K-F248XP-25s in N7K-C7009s, because the cost and value are really good, however I have some 100Mbps copper connections I'll likely be stuck with for a while. So... can I plug a GLC-T into a N7K-F248XP-25 and set the speed at 100Mbps?
View 1 Replies
I am sure that F1 linecards on Nexus weren’t able to support L3 functionality, so my query is does the F2 linecard (N7k-F248XP-25) on Nexus 7010 support Layer 3?
View 2 Replies View RelatedI am struggling to find an SFP transceiver, single mode, that operates at 100Mbps in a 1000Mbps port in an ME3600 or ME3800.
View 5 Replies View RelatedI have a 100mbps internet connection from my ISP but once the connection hits the ASA the download speed gets reduced to 15mbps. My network is setup as follows: ISP Modem ---- Edge Switch ----- ASA --- Internal Cisco Switches
If I plug my computer into an extra port on the Edge Switch I get speeds around 92mbps with normal traffic still going to the ASA. But when I plug into the ASA and internal switches I have speeds of 15mbps.
I have made sure that duplex/speed match on the links. I have done packet captures and within two minutes I do have several dup acks and retransmissions. The retransmissions don't seem to match the dup acks. (The retransmission is not for the dup ack requested so the dup ack keeps being resent)
The only interface error is on the inside interface which includes 700 overruns in a weeks worth of time.I am not using an IPS/IDS. I do have several vpns on it but was not going through a vpn tunnel. I am also using NAT.I am using an ASA 5510 8.2(1)
when am trying to plug a PC into the switch, it takes power as the switch is POE . but when trying to plug IP Camera Device it does not take any power. although i have cisco 2960 - 24 ports both PC and IP Camera getting power. while troublshooting by #show power inline , i get nothing as well.
View 6 Replies View RelatedI have a customer that has a stack of 3750x switches installed in production and now would like to install the powerstack cables. The switches are in production and downtime would like to be avoided. Can you install the powerstack cables with the switches powered up? I would assume you can, but wanted to verify before doing so.
View 4 Replies View RelatedWhat s the fabric speed (backplane speed) of a Nexus 2232 10G EX?What is the forwarding rate (Mpps) of the same 2232 FEX?
View 6 Replies View RelatedUpgrading a NX 7K. A scp copy of SO image from a server to NX7K bootflash is very very slow. It took more than an hour to copy 30% of n7000-s1-dk9-npe.5.2.7.bin
View 4 Replies View RelatedIs the fan speed configurable in n5k and n7k? my customer's n5k temperature already over 50 centigrade,but the fan still 50% speed,may i config them work in full speed?
View 1 Replies View RelatedI currently have a C3750G connected to a C3560G with default auto-negotiation settings. Ports are up and connected a-100 and a-full. I am trying to change the ports speed to 1G, and have tried all possible combinations of "speed 1000" and "duplex full" setting on both ends to no avail. What should port settings be for 1G speed between the two switches?
Here are the current port settings:C3750G:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
[Code].....
I have 5x Cisco 2960 and 1x Cisco 2960G. All of them are using IOS Version c2960-lanbasek9-mz.122-55.SE6.bin I'm having poor inbound speed with ALL of the Cisco 2960 (except 2960G) although the outbound speed is normal. The port is 100Mbps Full-Duplex, but the max inbound speed on a single connection is around 35Mbps. With the 2960G, I can get max 1Gbps inbound speed on a single connection.
I checked everything and still not know why the 2960 switches can't get max 100Mbps inbound.
I have connected a 2 TP trunk between 6509 and nx 7000, as shown above. I am trying to have speed 1000 on both sides.If I set speed 1000 on 6509 Trunk disconnect. How to force speed 1000? [code]
View 4 Replies View RelatedI am facing port speed issue on WS-C2960G-48TC-L series switch.This switch gig0/X ports connected to onother switches (Cisco and HP both switches are also gigbit ports and directly connected ).but interface is giving only 100mb/s output.ios on WS-C2960G-48TC-L is 12.2(44)SE6
View 15 Replies View RelatedI have had trouble to verify the support wireless speed and band that CISCO891W-AGN-A-K9 supports. I saw on a vendor website that it supports a max wireless transmission speed of 54Mbps but this seems low for what is supposed to be the current model wireless router which is supports 802.11n. What the maximum supported wireless speed and whether 5Ghz is supported? Plus I am thinking about purchasing it for my home wireless network (upgrading from an 871W).
View 1 Replies View Related3750G-12S-S.Problem description:I had a WS-3750G-12S-S in production with a defective fan tray and needed to change it.I faced to trouble with inter g1/0/1 on the new switch( it worked fine on the old).
Here the config for old switch:
interfacigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 111-113,278,790
switchpmode trunk
speed 100
[code]....
even if I configure speed nonegotiate that does not work.
I got a 6509 version 12.1(22)E2 that I am replacing with a 4510E version 3.40SG with Supervisor Engine 7-E. The 6509 is configured with 20 channel-group for dual fiver connection to ten 3550 switches with trunking enabled with isl encapsulation. The 6509 is the VTP server to each of the 3550 switch clients. There are 40 Microsoft Servers attached ot the Gig RJ45 port modules.
I have attached the 4510 to the 6509 with dual fiber connection configured as a channel group with trunking enabled. I am configuring the 4510 the same as the 6509 except I have to use trunking with dot1q encapsulation because isl is not supported on the 4510. I no longer want to use VTP with the 4510 and have set the it as transparent mode. Each of the 3550 switches are changed from isl trunking encapsulation to dot1q and VTP mode is changed to transparent when they are moved from the 6509 to the 4510.
I want to move the switches over a few at a time and not all at once. The first 4 switches attached with no problems and ran with no problems for the user access to the servers still on the 6509 for a week. Then I found out DHCP was not working for the devices attached to the switches on the 4510. I moved one of our domain controllers form the 6509 to the 4510 to fix the DHVP problem. I have now added 2 more switches with users that use an application on a server still on the 6509 and they are getting disconnect errors after logging into it and using it. Other applications on different server also on the 6509 are having no problems. I moved the switches back to the 6509 to get the users up during business hours. I now plan on moving the server for the application that was failing to the 4510 in hopes that it will fix the problem.
Is there something I can do to speed up the connection between the 6509 and the 4510 so I can continue this transition without having to move the servers to the 4510 as I move the users?
We have an old 3508XL switch. We are trying to connect a new 2960 to it but we purchased the incorrect SFP insert and that speed can only do 100mb. We are getting link flaps and we suspect that it's a speed issue between the two. However, I cannot find how to set the speed on the old OS of the 3508 switch.
Below is a show version of the 3508 switch.
LR0007>show ver
Cisco Internetwork Operating System Software
IOS (tm) C3500XL Software (C3500XL-C3H2S-M), Version 12.0(5)WC17, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Tue 13-Feb-07 15:04 by antonino
[code]....
I am troubleshooting some speed issues that I might be having and using TTCP and iperf/jperf. I am testing the LAN speed between our local router and local desktop.
When I run TTCP transmit on the Cisco and receive on the local desktop I get speeds right around 90Mbps, which I would expect because the switch between the Cisco router and the desktop is only 10/100.
When I run TTCP receive on the Cisco and transmit from the same desktop I only get speeds of about 24Mbps to the router.
The router is a 2911 wiht gigabit ports. The switch between the 2 devices is only a 10/100 switch, so I expect to only get around 90Mbps but 24 seems very low.
Our client having one c3750 with ipbase license switch.They are connected server and end switches to that switch.Our customer want to increase the speed to accessing the server at that time I am told to use etherchannel.Customer happy about this and implement the etherchannel configuration.Now i need to configure etherchannel upto 4 physical link.server are connected on port no Ge1/0/10,they want to bind four phical link GE1/0/10-13.how to configure etherchannel in this switch?
View 1 Replies View RelatedThe WS-X68xx series line card has a fabric of 40Gbps and a 16 Port 10GE has a 4:1 oversubscription rate. The WS-X6908-10G has a fabric speed of 80Gbps and has a 1:1 oversubscription rate.
If I mixed the 68xx and 69xx series line card, do I get 80Gbps for the 6900x and 40gbps for the 68xx line card? Or would the 69xx series line card be downgraded to 40Gbps?
From my understanding, the 68xx series has a DFC card and thus the fabric speed operates independently.
I have working internet behind cisco 2811 on all vlans however upload speed is very slow and ftp server download is slow and times out, previously when directly connected to modem/router was fine? This is router config below:
Current configuration : 2229 bytes
!
! Last configuration change at 02:21:18 UTC Tue Mar 12 2013
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
I have in my office switch Cisco Small business series SG300 with 50 x 1G ethernet ports. Now I wanna enlarge my network. I want to buy Cisco SF200-48 with 2 x combo Gigabit SFP . My question: is it possible to connect SF200-48 to 300Series at 1G speed over ethernet? Can I use ethernet port on combo Gigabit SFP on SF200 like uplink and connect it to any port in 300Series?
View 1 Replies View RelatedI got a Cisco 2800 router and am planning to use FastEthernet 0/1 to trunk in 802.11Q VLAN's to cater for some of our radio links. speed and operation of the sub-interface that will be created. Or explain it here. We got a radio link that we want to trunk into this Cisco 2800 and it is suppose to be connecting at 100Mbps but currently operating at around 80Mbps. Reports shows that the max in and out traffic for this link this year till today is 25Mbps. Will it not fail teh CPU etc ?
interface FastEthernet0/1
no ip address
!
[Code]....
I put a QoS in a WS-C3560CG-8TC-S version 12.2(55)EX2. in our lab file upload or download speed much reduced and drop the packets with QoS everyting is fine without QoS
Here is the config: My question is why I speed reduced a lot and packets to be dropped with QoS.everything is fine WITHOUT QoS.
class-map match-any VoIP description Voice IP Phone RTPmatch access-group 157
class-map match-any WEB description Internal Web, SSL Web, DNS query, Pinnaclematch access-group 153
!
policy-map QOSMARK
class VoIP set dscp ef
class WEB set dscp cs3
[code]....
I have 10Mbps internet speed connected to ciusco router 1841 that has 2 internal NICs. One NIC has a full 10Mbps download speed and the 2nd NIC is currently limited to 1Mbps download speed. I want to change the download speed of the 2nd NIC to 4Mbps? How do I do this on a cisco 1841 Router?
View 8 Replies View Related9x3750E stacked switch (WS-C3750E-48PD-SF0) (15.0(1)SE2
C3750E-UNIVERSALK9-M)
2x10Gbe uplinks from EMC NAS
At a basic level, we have found that the 10Gbe uplinks have slow read performance with or without a port-channel configured (2-3 minutes for a 700MB file to desktop from the NAS) We switched back to testing a 1Gbe and the read speed is normal. Another anomaly is Win7 / 2008 machines read speed is fine from the NAS while the 10Gbe uplinks are in production?!
Write speed is great on 10Gbe. Only read speed is affected!! the switch is not reporting anything abnormal. We looked at SMB/SMB2 as another possible cause...
mls qos is enabled on the switch but not sure if this is affecting performance.
Is the ANY config that I need to carry out on the interfaces to get the read speed working as it should for both Win7 and WinXP. (MTU is 1500 throughout the enterprise, NAS included).
I have a question about speed negotiation process between interfaces. I have 3650X Sw and 2960S-48port. All ports of two are GigabitEthernet, however the link between them is only 100Mb/s, Full duplex. I try to set the speed 1000 Mb/s manually in the interface then the interface never up. Its status is down/down. I must set back to speed auto. I show interface Gigabit0/24 in Sw 3650-X and figure out that there are many output drop (over 600000). I clear counter then after two days the output drop is over 70000. This link is trunk link between two switches, all ports of access SW are Gigabit and connect to PC. First, I thinks the 3650X is throttled somewhere in output direction of trunk link. But there is another trunk link (Gi0/23) to another 2960S-48port and no output drop number in this interface. This Giga 0/23 speed is 1000 Mb/s (auto speed, auto duplex)
Does any outside things impact the speed negotiation process between 2 interfaces? And output drop number may caused by abnormal speed between two Gigabit interface?
I have 1841 router with Gigabit Ethernet HWIC with One SFP Slot installed in it and connected via SX Multimode cable to 2950 switch. I have 5 VLans in trunk. The question is what will be the speed rate between VLans - 1 Gbps or less?
The case:
Port 1 assigned to a VLan10 and Port 2 Assigned to a VLan20 on 2950 switch.
InterVLan routing is configured on 1841.
Computer A is connected to Port 1 and Computer B is connected to Port 2 on the switch.
What be a file transfer rate from Computer A to Computer B assuming that NICs on both computers are 1000Base-T.
I can´t configure speed in a giga port on WS-C3560-24PS-S switch(config-if)#speed ? no negotiate Do not negotiate speed
do you know if the port support speed 100??
because I need to connect with 2955C-12 switch in one port: 100BASE-FX (Multimode Fiber) uplinks, this port its only 100mbps?
and the switch C3750G-12S-E can I configure the ports on 100mbps?
I have a 2610 router. How can I tell if the built-in ethernet port is only a 10BASE-T or if it's a 10/100 port? Is there a "Show" command to give me this information or did it only come one way? I have found conflicting information on this :-( If it's only 10BASE-T, can I upgrade it to 10/100?
View 8 Replies View RelatedI want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies View RelatedI am trying to hard code the speed and duplex settings on interfaces gigabit 0/1 - 2 interfaces with out success.
DSW121(config)#interface range g0/1 - 02
DSW121(config-if-range)#speed ?
Nonegotiate Do not negotiate speed
[Code]...
I have NM-16ESW card installed in one of my 3845 router. Below is the sh inventory output
NAME: "16 Port 10BaseT/100BaseTX EtherSwitch", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
PID: NM-16ESW , VID: V01 , SN: FOC11482484
NAME: "Gigabit(1000BaseT) module for EtherSwitch NM", DESCR: "Gigabit(1000BaseT) module for EtherSwitch NM"
PID: GE-DCARD-ESW , VID: V01 , SN: FOC11454FW6
Is the Gig port available here can be used for uplink?I found following comment at
[URL]...
"GE-DCARD-ESW: This optional 1000BaseT Gigabit Ethernet port for NM-16ESW and NMD-36-ESW can be used for a gigabit connection for a file server or for intra-chassis stacking of the Cisco EtherSwitch module. Stacking is supported in Cisco IOS release 12.2(11)T and beyond"
