Cisco Switching/Routing :: Upgraded 3560-48-PS Could Not Get IP

Oct 24, 2011

I upgraded our 3560-48-ps switch from c3560-advipservicesk9-mz.122-35.SE5.bin to c3560-ipservicesk9.mz.122-55.SE4bin and is having issues now.
 
Since I upgraded to the new IOS our older machines on the network can no longer connect to the domain and is not getting an IP address sh ip dhcp binding and sh ip dhcp conflict does not show any output, however all newer machines on the network received dhcp addresses without any problems and can connect to the network and internet.
 
For testing purposes I put the old IOS back on the switch and the older machines could connect again and received dhcp addresses.No other changes were made to the config.
 
I did a comparison on Cisco's website and both IOS's support DHCP. Not sure why the new IOS would not give any output when I ran the commands.older machines : Apollos and NCS (They all have XP service pack 2 with Intel 2.8 processors.)

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 3750 3 Units Of Stack Upgraded

Mar 29, 2013

I have a situation where are three units stack of 3750 which i need to upgrade.The flash memory on all the switches are the same which is 57.4 MB. The tar file which I was trying to use was 21 MB.
 
Now the trouble is that the client wanted to do upgrade without overwriting the existing file.  I tried doing automatic upgrade using tar file. It started all OK with downloading the tar file successfully on the master flash. but then it failed thereafter. It did not show any error on my telnet screen however I could see errors (Error code 10054) on the TFTP server regarding the download of the same file on the flash ( i am guessing this was the flash of the next unit in the stack).
 
" You need to make sure you have sufficient space available in the Flash  of the master switch. The master switch should have twice the amount of space of the .tar image file size. This space is needed to store the .tar file as well as to store the content of the .tar file that you extract."
 
The tar file being 21 MB and looking at the dir below I dont think it is possible use this option since I dont have that much space. I have 34 MB free which according to the doco should be atleast 42 MB.what is the best option I have with me given the constraints that I cannot upgrade the flash at this stage.

1. Could I use the manual upgrade (using bin file) if that can do the needful,

2. Do I simple try automatic upgrade using tar file but with overwriting option so it overwrites the existing image on the flash.Could i take a copy of the existing image on the tftp server using "archive upload-sw" command?

3. Is there a way I could upgrade without transferring image onto the flash and instead using tftp for the stack switch to boot from?

View 16 Replies View Related

Cisco Switching/Routing :: C2960G-48TC-L Upgraded To 15.0.2-SE1 Now Low On Memory / No SSH?

Jan 16, 2013

I managed to upgrade this C2960G-48TC-L from 12.2.35-SE5 to 15.0.2-SE1 and now I can't connect anymore via telnet nor ssh. Console output simply shows
 
%% Low on memory; try again later

View 8 Replies View Related

Cisco Switching/Routing :: Upgraded 2960 Switches To 15.0 (1) SE - Syslog Message On Bootup

Oct 8, 2011

I recently upgraded a few 2960 switches to 15.0(1)SE, and while they are working fine, I did notice a strange syslog message upon boot-up that wasn't previously there. [code] I did some cursory searching via google but nothing useful presented itself.

View 7 Replies View Related

Cisco Switching/Routing :: 3560 Policy Based Routing Verify-availability

Apr 19, 2012

Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop"  do not do the same job.

View 8 Replies View Related

Cisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch

Dec 8, 2011

The last few days I've been exploring options in getting rid of some old routers accross a wan connections.  I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch.  I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect.  I'll post the config and a few commands so you can see what the basic setup is. 

Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254.  Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]

View 4 Replies View Related

Cisco Switching/Routing :: 3560 VLAN Routing Between Switch And Router

May 8, 2012

I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
 
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?

View 9 Replies View Related

Cisco Switching/Routing :: Make Policy Based Routing On 3560?

Apr 17, 2012

I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M)  For below configuration there is no problem and pbr is working.
 
“Access-list 100 permit ip host  1.1.1.1 host 2.2.2.2
Access-list 101 permit ip host  1.1.1.1 host 3.3.3.3
 Route-map pbr1  permit 10
Match ip address  100
Set ip next-hop verify-availability  1.1.1.2 1 track 11
 interface fasthethernet  0/1
ip policy route-map  pbr1”
 
But when i add another sequence to the "pbr1" with another sequence number  like that.
 
“Route-map pbr1 permit  11
Match ip address  101
Set ip next-hop verify-availability  1.1.1.3 1 track 12”
 
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based  Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.

View 16 Replies View Related

Cisco Switching/Routing :: Routing Secondary Network On 3560 Switch

Jun 4, 2013

I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch.  The switch is running the following IOS version: [code]
 
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
 
What would be the best way to get the two workstations talking via the switch?

View 3 Replies View Related

Cisco Switching/Routing :: 3560 - Access List On InterVLan Routing

Dec 11, 2012

I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
 
The configuration is
interface Vlan1
description Data VLAN

[Code].....

View 14 Replies View Related

Cisco Switching/Routing :: 3560 - Unable To Perform VLAN Routing

Apr 28, 2012

We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing.  We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.

View 17 Replies View Related

Cisco Switching/Routing :: Catalyst 3560 - Routing Enabled With / Without Default Gateway Or IP Route Command

Feb 25, 2013

We have two catalyst 3560 switches running  c3560-ipbasek9-mz.122-58.SE2.bin  They are connected using etherchannel using gi 0/21 -  24 interfaces.
 
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
 
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
 
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?

View 4 Replies View Related

Cisco Switching/Routing :: 2504 WLC / 3560 Catalyst Routing

Oct 21, 2012

I have a 2504 WLC connected to a Catalyst 3560 which has multiple vlans and is connected to a 2800 series router. I know the catalyst is L3 but I am needing nat functions to get outside to the internet. From my 2800 series router I am able to ping out to the internet, also I am able to ping the vlan interfaces on the catalyst switch. Problem is from the catalyst switch I can ping the inside and outside address of the 2800 but I cannot get any further then that. I cannot ping the 2800 router gateway. Not sure what I am doing wrong as far as routing.
 
I've attached my 2800 and 3560 configs.

View 3 Replies View Related

Cisco Switching/Routing :: Upgrade The IOS In 3560?

Oct 7, 2012

I am trying to upgrade the IOS in 3560 but I am facing one issue. Its flash is 15MB & available space is 8MB whereas the IOS is of 11MB. How can I upgrade the IOS without upgrading the flash?

View 4 Replies View Related

Cisco Switching/Routing :: 3560 / PoE Is Not Working?

Mar 10, 2013

We bought a 3560 PoE switch to replace tons of PoE-injectors but when connecting the devices our logs were flooded with
 
Mar 11 15:09:20.725: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD
Mar 11 15:09:20.725: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
Mar 11 15:09:20.968: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down
Mar 11 15:09:20.985: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD
Mar 11 15:09:20.985: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
 
While the message seems quite clear im wondering if there's any workaround on the problem?

View 13 Replies View Related

Cisco Switching/Routing :: 3560 Need To Add 2nd Trunk

Jun 6, 2013

I have a Cisco SW ( 3560 ) with one Trunk link to my router ( 7606 ), Trunk link is fully utilized so i need to add 2nd Trunk.Shall all move some customers from old trunk to 2nd one and create a new subterface for them ?I am think if i can create bundle and add subinterfaces under this bundle ?Add two GE ports to be memeber of this bundle ?

View 5 Replies View Related

Cisco Switching/Routing :: QOS On Catalyst 3560

Oct 28, 2012

We have a IP-phone system connected to port 1 on a 3560 switch, the phone system tags traffic with dscp. The switch uplink is on port 24.
Is this configuration correct:
 
interface 1:
auto qos trust
 
interface 24:
priority-queue out                 

View 3 Replies View Related

Cisco Switching/Routing :: 3560 IOS Upgrade And PBR

Nov 21, 2012

I have a 3560, which is being used as our core router that I have recently installed. It still has the standard IOS which came with (C3560E-UNIVERSALK9-M) it but I need to implement policy based routing so need to upgrade it and have downloaded c3560-ipservicesk9-mz.122-58.SE2.bin and indeally would like to install it in the morning before people start work.

I have 2 questions, 1, Is the ipservices capable of PBR as I have been reading conflicting reports, in fact my friend who works for Cisco has advised that it is not possible on the 3560.

2, When I do upgrade will there be any current configurations that are not compatible with the new one, I wouldnt image that there would be any but just wanted to make sure as it would be the biggest headache ever if it went wrong.

View 7 Replies View Related

Cisco Switching/Routing :: How To Configure QoS On 3560

Nov 23, 2011

I configured following command to implement QoS on Cisco 3560.
 
class-map match-any IND
match access-group name Lync
 policy-map LyncAV
class IND
set ip precedence 4

[code]....

how to apply this QoS on interface?

View 3 Replies View Related

Cisco Switching/Routing :: 3560 POE Lost Ios?

Jul 29, 2012

I have a 3560 POE that will no longer boot and I am not able to load a fresh copy of software onto it.  It appears that it has lost all data.  When I attempt to TFTP a new IOS, I receive that following error: 
 
Transfer cancelled by remote system
 
I have tried using dir flash: to see what is contained in the flash directory but I receive the below message:
 
unable to stat flash/: no such device
 
I am stuck in rommon mode so when I do switch: dir command, I don't even see flash as being a filesystem.  The below list are the only systems registered.
 
bsdcs[0]:  (read-only)
bstage[1]: (read-only)
fstage[2]: (read-write)
xmodem[3]: (read-only)
null[4]: (read-write)
tftp[5]: (read-only)
 
Is this switch finished or is there something else I could try? 

View 8 Replies View Related

Cisco Switching/Routing :: 3560 Switch With LAN QoS

Jun 5, 2012

I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes  according to LAN QoS configured on interface
 
we have configured  both the commands shape and share.
 
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC  , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?

View 5 Replies View Related

Cisco Switching/Routing :: 3560 Layer 2 QoS

Mar 17, 2013

I found that when I enabled layer 2 auto QoS in 3560 switch, I need to wait so much time to open a file in network drive. Howerver, when I disable the Qos. It can improve a lot. I have used a sniffer to capture the packet to see. Those default packet is in DSCP 0. Therefore, I think majority packet will drop to queue 4. How can I increase the buffer and threshold in order to improve queue 4 performance.

View 1 Replies View Related

Cisco Switching/Routing :: 3560 - PBR Not Applying To SVI

May 12, 2013

We have two L3 3560's.  One 3560 has an upstream MPLS router.  The other 3560 has an upstream backup VPN router.  Both of these 3560's are L3 switches with IP routing enabled.  I created a PBR on both so that specific traffic routes through the MPLS router, while other traffic routes over the backup VPN router.  I'm trying to apply the PBR to the SVI's, on each switch.  However, when I do a "sh run", the PBR does not appear under either SVI.  I've enabled the SDM Routing template, made sure that ip routing was enabled, and even verified that the IOS has the capability.  Not sure what else to check for.

View 8 Replies View Related

Cisco Switching/Routing :: 3560 - QOS Classification

Sep 21, 2012

I've a question about QoS classification on Cat3560 From
 
"When QoS is enabled with the mls qos global configuration command and all other QoS settings are at their defaults, traffic is classified as best effort (the DSCP and QoS value is set to 0) without any policing. No policy maps are configured. The default port trust state on all ports is untrusted."
 
Now, when mls qos cos override is configured on a port, how is the switch behavior ? From documentation "All the incoming QoS values are assigned the default QoS value configured with this command". However I believe the port state is "untrusted".....so which DSCP values are assigned to them ? Is used a Qos-to-dscp map to derive the QoS label from the (overridden) QoS value also in this scenario ?

View 2 Replies View Related

Cisco Switching/Routing :: 3560 - QOS Scenarios

Jul 1, 2012

Consider the following case: 

PC1-----Acess link--f1/1--SW1-- Acess link---------F 0/1-R1-acess link-------Sw2-----trunk--------SW3-f1/4--------PC2
 
All switches are multilayer switches ( 3560) Pc1 and PC2 are running Cisco Soft phones. If  we configure SW3 with: int f1/4  
mls qos trust dscp.

1)Does the above command require SW3's  f1/4 be configured as layer 3 port not layer 2? ( My reasoning is since Sw3 has to get to Ip header to process DSCP values, therefore Sw3'f1/4 should be configured  for layer 3 operation.) 

2) What if sw3 were not 3560 but layer 2 switch such as old 2900 series. can layer 2 switch be configured with: mls qos trust dscp.?  Will layer 2 switch be able to interpret dscp values and perform QOS ? ( My understanding is layer 2 switch should not be able to read dscp values ). I  will be posting few more questions on the above scenario.

View 7 Replies View Related

Cisco Switching/Routing :: IP Inspect On A 3560 IOS?

Mar 4, 2012

I have a need to use a 3560 switch to terminate a provider's internet connection, but want to secure it so that it and the vlans connected to it are not wide open. At the same time, I'd like to use stateful packet inspection.
 
I have IOS 12.2(44)SE2, but IPBASE running on my 3560s. Is there an IOS (perhaps the ADVIPSERVICES of that version?) that allows a 3560 to use the 'ip inspect' command?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 3560 With GRE Support

Feb 7, 2012

Does the Catalyst 3560 support GRE ?
  
I know that Catalyst 3750X support GRE ,but Catalyst 3750X cannot work in hardware it.
  
Does the Catalyst 3560 cannot work in hardware too? 

View 4 Replies View Related

Cisco Switching/Routing :: 3560 - Possible To Delete VLAN?

Dec 5, 2011

Is there any way to check if this VLAN is used by somedevice?

Cisco3560#sh ip int b
Vlan55                unassigned      YES NVRAM  administratively down down

Cisco3560#sh vlan
VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active
55       Print                        active    Fa0/5, Fa0/6, Fa0/7, Fa0/8

View 18 Replies View Related

Cisco Switching/Routing :: How To Take Event Log Of Switch 3560

Feb 26, 2012

how to take the event log of Cisco switch 3560, its argent.

View 1 Replies View Related

Cisco Switching/Routing :: Implement QOS On 3560 Switch?

Nov 22, 2011

I have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig  interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version? 
 
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.

View 3 Replies View Related

Cisco Switching/Routing :: 3560 Download Not Available / Missing

Oct 11, 2012

I am currently doing an audit at a customer site, i.e. am checking if any IOS upgrades are needed. I have found that alot of IOS versions that the customer is running are not available in the Cisco Software Download area anymore. Taking IOS 12.2(44)SE2 for the 3560 for example: some earlier and later versions are available as downloads, but this exact version is not. It also is not listed as a deferred version.What is Cisco telling us with this exactly? Are these "missing" versions not supported anymore i.e. is an upgrade to a supported version adviseable?

View 2 Replies View Related

Cisco Switching/Routing :: 3560 - CEF Has Been Disabled Due To Low Memory

Jul 15, 2009

I have a 3560 connected to an edge device and I keep etting this error.  I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that.  I can't seem to find any documentation on this error. I understand what it means, I just don't know how to resolve the problem.

View 3 Replies View Related

Cisco Switching/Routing :: DHCP Relay On 3560

Apr 12, 2012

Would like to impliment VLAN's on Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(25)SEB4...But I need a DHCP Realy to my Windows Based DHCP Server.  How do I enable DHCP Relay on the 3560?

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved