I need 891 SEC router. I think this comes with advanced IP services.What I have is 1921, with IP Base.Can I upgrade 1921, so it will become alternative to 891 SEC ?
View 1 RepliesCisco announced EOL for ws-x6148A-GE-45AF line card and proposed WS-X6148E-GE-45AT. However this card seems not to be supported by the SUP2T-10G supervisor. Which alternative card should I take for this EOL line card, or can I use the proposed line card (use extra daughter card DFC4)?
I'm looking for an alternative line card for the 650x-E chassis with Supervisor 2T iso 6148-GE-45AF
From what I can find the ASA does not support policy routing.
I have two VLANS that need to go to the same destination but different routes. Anyway to accomplish this on the ASA?
I found the following on the link bundling page for the 12000 series router:"In both EtherChannel and POS channel link bundles, the Link Aggregation Control Protocol (LACP) for signalling and the 802.3ad protocol for automatic negotiation of the channel are not supported. This means that in order for the channel between two routers to be active, you must disable signaling on switches (such as the Cisco 6500/7600 Series) in the channel, and configure the switches in ON mode."
So, my question is, if lacp isn't supported, is there another way to mimic its functionality on a 12000 series router? I want to connect 2 routers together with a port channel that will pass through our layer 2 network, and I want to make sure that any failures in the path will shut down the affected link on both routers.
We have an ASA5510 with a backup ISP connection protecting our corporate network. I also have a mail server and I would like to route SMTP traffic over the backup network. I realize that the ASA5510 does not support PBR, but I also know that I can use static NAT rules as a workaround to direct specific types of traffic over a particular interface (e.g. "static (outside,inside) tcp 0.0.0.0 www 0.0.0.0 www netmask 0.0.0.0" and "static (backup,inside) tcp 0.0.0.0 smtp 0.0.0.0 smtp netmask 0.0.0.0"). is it possible to use something similar to force a particular host to use a specific interface? I have tried to make this work on my own without success. Is it even possible?
View 5 Replies View RelatedI want to migrate Exchange server to Exchange 2010, I would like to know if ACE and SSLM support Subject Alternative Name (SAN).
1. Can the current CSM (WS-SVC-SSL-1-K9) support SSL certificates that have Subject Alternative Names? I.e. a certificate that has both of these names in it.
a. exchange.ww.edu
b. legexchange.ww.edu.
2) Can the new ACE( ACE20-MOD-K9) support SSL certificates that have Subject Alternative Names? I.e. a certificate that has both of these names in it:
a. exchange.ww.edu
b. legexchange.ww.edu
i have met connection problems (mainly with xp)where a laptop always have problem connecting to a secured wifi connection that has higher encryption than wep (wpa - wpa2).In general after a few tests . I am almost sure that it is xp's Wireless Zero Configuration's problem.I am wondering if there is alternatives to WZC that does not require their own brand's device to run a 3rd party Wireless Connection Manager.I am not looking for a model specific software either ,
Examples are:
toshiba connect me
tp link connection utility
intel's mobile
Our company is starting to open a lot of small mpls sites across the nation. By small I mean less than 10 users, voip, 1 dc, that's it. Instead of getting the usual 2901+2960 combo, I'm interested in finding less expensive solutions. Maybe an L3 switch like a 3750? These are temporary sites so management is fine with looking into used, non smartnet covered gear?
View 7 Replies View RelatedAs per me 24x7 network monitoring service is one of the best technique.Even we can protect large scale or enterprise level network with unwanted attacks or virus. Alternative better option of Network Monitoring Service
I am in need of a Static IP alternative (My ISP chooses not to offer the service). I do not need the Static IP to access my own devices. I need to access other networks as a "trusted" user.
View 10 Replies View RelatedI generated a wildcard certificate for my company type *. [URL] in a CSS 11501. For the site [URL] worked fine, for the site [URL] didn't worked. I read on the web that should generate a wildcard certificate with subject alternative names. Is it possible in CSS? how can I do it?
View 5 Replies View RelatedMine studio 1555 with intel core 2 duo P8700 [URL] processor and intel wifi 5100 agn card stopped connecting to router since last week. After searching a lot I found out that the Intel has stopped supporting 5100 for windows 8. Is there any way possible to use the same adapter with compatibility drivers on windows 8?? I have searched a lot but couldn't find much. All the new intel cards like "Intel Centrino Wireless-N 2200", n6300 are of 22nm while my processor is of 45nm. So will the newer card work with my processor.
View 1 Replies View Relatedwhat other cards are compatible with XPS 13 Ultrabook? Like so many people, I have been having a problem with my wifi when the computer is used a little far from the router, and thinking about buying a new wifi card for a replacement (which is silly, and I shouldn't have to do, given my computer is brand-new and cost more than £1000, I know... but I don't seem to have much choice). I've tried everything that has been suggested in the Dell forums, and elsewhere, including those on the Intel site. But nothing has improved my connection even a bit.I have Windows 8 (64-bit). And it currently has an 'Intel Centrino Advanced-N 6235' wifi card that came with it.
View 2 Replies View RelatedI configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
Any "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies View RelatedI have an ASA 5510, with Ethernet0 connected to Internet via a T1 line, Ethernet1 connected to LAN1, and Ethernet2 connected to LAN2. LAN1 & LAN2 are independant, but share the Internet connection, via the T1 line. On LAN2, I have another router that connects to the Internet, via a Comcast line. I wish to route some of the traffic on LAN2 (10.38.77.0) to the other Router, on LAN2 (10.38.77.12) (connected to the Comcast line). I have entered the following lines:
route inside2 10.11.0.0 255.255.0.0 10.38.77.12 1
route inside2 10.252.0.0 255.255.0.0 10.38.77.12 1
route inside2 172.22.6.0 255.255.255.0 10.38.77.12 1
I can trace the routes from the ASA 5510 (1st hop is to 10.38.77.12), but not from anything else on LAN2.
When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies View RelatedI have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
I have an 1811 with several subnets connected to it.I recently installed a 3750x plant and want to bring my interior routing back to it.
All the routing is handled by the 1811 via secondary interfaces on vlan1?
I have 192 ports, and subnets show up on almost all of them. None of the ports are assigned to any specific vlans. Most ports have several subnets on them.
What is the best approach to getting the 3750x to handle the routing?
We have small which I'm looking to implement and have built this on GNS3.
We have:
Router A in site 1
Router B in site 2
Router C in site 3
Router A and B are connection via a point to point 100M link and from Router C we have a 2 point to point one of which is 5Mpbs and going to Router A and Router B.
For Router C to reach Router A network it will go via Router B and these are 100M connection. When the link between Router A and B goes down. Router C should update and start using the 5m route.
For some reson, the routes are not updating. I have to do 'clea ip eigrp ne' for the routes to update and if I reload the routers all works well, it seems the problem is intermittent.
I’ve been trying a few days now to implement multicast routing on my home network in order to make airplay work between subnets. Specifically between an iphone and a hifi separated by different vlans. Failed, as I have no experience in multicast routing. we have a clean configuration and simple network which consists of two SVIs
Vlan 10: 192.168.1.0 255.255.255.0
Vlan 20: 192.168.2.0 255.255.255.0
ios platform cisco 887
I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies View RelatedI have an 891 router setup to support 4 VLANS with 4 DHCP pools. The router is in place at a charity HQ and I have been asked to setup remote access for around 8 users who will need to be able to connect to a NAS drive via IP on one of the VLANS. I have had some experience with SonicWall devices that use SSL VPN's and would like to do similar here.Can someone start me on the right track to get this working.
- Presumably I need an SSL-VPN license for the router.
- What sort of client will my Windows and Mac based clients need? (with sonicwall it was a proprietary cilent called NetExtender)
- Any other pointers or comments?
I'm not a Cisco engineer, but did manage to set the network up thus far. Everything about this charity is non-profit / cost including the support staff like myself
I have an 881 router here in house and am attempting to enable the gui interface on the router.
I have tried the steps to enable http but have not had any success. Below is the IOS Version and the portion of the show config that reflects the http allow:
ROM: System Bootstrap, Version 12.4(15r)XZ2, RELEASE SOFTWARE (fc1)
Cisco 881 (MPC8300) processor (revision 0x100) with 249856K/12288K bytes of memory.
Processor board ID FTX1249Y16Q
[Code].....
I am a service provider, with the task of installing a systech device at a site, and was told all I needed was DHCP enabled and dynamic IP for the internet. The site just put in broadband and their router has a single port. I picked up a linksys dsl router to use as a router/switch to enable more ports for the internet. If I hook the broadband router into the internet port of the linksys, I can not get internet access on my laptop through it. If I hook the broadband to port 1 and my laptop to port 2, I have internet access. If I hook the systech device to port 3, the support team says they cannot see the device. But, if I hook the broadband directly to the systech box, they can find the mac address and download to it. I have set the linksys to default settings, but will not work.
View 2 Replies View RelatedI've got working PAT, but absolutely not sure how to perform additional task.
ip cef
no ip bootp server
no ipv6 cef
interface FastEthernet8
ip address 192.168.1.141 255.255.255.0
duplex auto
speed auto
[Code] ........
It doesn't seem like I can set up trunking (dot1q) on this device. Isn't it supported on this device? Can I still set up VLANs with the router-on-a-stick concept working internal in the device, i.e no external interfaces/subinterfaces being configured? If so, can I then connect VLANs to other switches? I have:
-876 ISR
-Catalyst 2960
-SLM2008
I know the small biz switch supports VLANs and I think trunking as well--obviously the 2960 supports it. Is there a way with these devices to configure one VLAN for servers/net devices and another for regular end-user computers so that they still talk to one another, or do I need a different router in the mix?
The problem is that that the routers are not reachable form the corporate LAN after some time. Pinging the routers IP is not working anymore. When the network cable is unplugged and plugged in again the routers are responding again. The same applies when I connect my Laptop to the router. The interface is responsive right after I connect the cable. Also other devices on the network can ping the router. But after a few hours or sometimes 1,5 day the router is unreachable form the corporate network.
The problem first started a few weeks ago. The configuration did not change. The router 878 was not responsing and after changing all the cables and conncting it to another swith the problem remained. So I suspected a hardware failure and bought a replacement 888. After configuring the 888 it showed the same behaviour as the 878 router. The DSL connection is working all the time. I can even set up a vpn connection to the router and start a telnet session. than I can ping the internap IP of the router but pinging another device is not working.
What I noticed after the command sh int vlan1 is that the last input counter keeps increasing.whats causing this or how to debug?
I do not understand where in the CCP I can configure PAT for communication back 7960G VoIP phone with SIP firmware Maybe I'm wrong on the concept of communication pass back to the Voice VLAN.
View 1 Replies View RelatedI have a cisco 877-k9 router whit 12.<15>T5 system, dram 128MB and 24MB. I want upgrade this correctly. Where is ios correttly supported?
View 4 Replies View RelatedI am a newbie to Cisco. I am trying to setup NAT with DHCP in our office on CISCO 819 router. I am having a problem with DHCP not assigning an IP on vlan1. I cannot figure out what i'm doing wrong. Below is my config and debug from DHCP.
router#sh config
Using 4328 out of 262136 bytes
!
! Last configuration change at 05:56:39 UTC Mon May 13 2013 by cisco
! NVRAM config last updated at 05:57:16 UTC Mon May 13 2013 by cisco
[Code]....
I am trying to connect a cisco 800 series router using adsl to a bt router/hub. This didn't work at all - so the cisco router is now connected to the bt router using a switch and the adsl cable. When I connect my pc to the cisco router, it doesn't go on the subnet it's supposed to be on. it's set to the gateway on the cisco router and the pc is set to 192.168.3.252. The bt router is on 192.168.1.x. When I connect a pc to the cisco router, and assign an ip address e.g. 192.168.3.123 it doesn't have any internet connectivity, but when I set it to get the ip automatically, it gets the ip address.
View 0 Replies View RelatedI want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....