Cisco VPN :: Allow Access For VPN Client To Spoke Network Through ASA 5520?
Mar 26, 2012
I'm trying to set-up 3 remote access groups on an ASA5520 running version 8.4(3) software so that remote clients connected via Cisco VPN Client can also access spoke networks which are also connected to the ASA. I've previously set this up on ASAs running v7.2 software without issue but don't seem to be able to do the same here and can't for the life of me figure out what's wrong!
I have set-up the 3 remote access groups:
Group 1 - subnet 192.168.1.48/28Group 2 - subnet 192.168.2.0/25Group 3 - subnet 192.168.3.0/25
My remote access user groups can all connect to the head office subnet (10.0.0.0/8) without issue. But only one of the groups (192.168.1.48/28) appears to be able to access the spoke sites (172.30.10.0/24 and 172.30.20.0/24) that I have set-up. However, I can't see what the difference is between the 3 groups I have configured so can't understand why it works ok for one group and not the others?
When I use the packet tracer, it tells me that the flow is being dropped at the VPN encryption phase but why is that? How can I find out more? Here's the relevant config on my ASA:
!same-security-traffic permit intra-interface!crypto dynamic-map remoteuser 5 set transform-set ESP-3DES-MD5crypto dynamic-map remoteuser 5 set security-association lifetime seconds 28800crypto dynamic-map remoteuser 5 set security-association lifetime kilobytes 4608000!crypto map outside_map 65000 ipsec-isakmp dynamic remoteuser!ip local pool pool1clients 192.168.1.49-192.168.50.54ip local pool pool2clients 192.168.2.1-192.168.2.126ip local pool pool3clients 192.168.3.1-192.168.3.126!access-list split-tunnel-pool1 standard permit 10.0.0.0 255.0.0.0 access-list split-tunnel-pool1 standard permit 172.30.10.0 255.255.255.0 access-list split-tunnel-pool1 standard permit 172.30.20.0 255.255.255.0 !access-list split-tunnel-pool2 standard permit 10.0.0.0 255.0.0.0 access-list split-tunnel-pool2 standard permit 172.30.10.0 255.255.255.0access-list split-tunnel-pool2 standard permit 172.30.20.0 255.255.255.0 !access-list
[code].....
View 12 Replies
ADVERTISEMENT
Mar 15, 2012
Have asa 5520 ver 8.0(4) I have vpn client access created and working I have l2l vpn created and working with another set of asa The issue at hand VPN client from internet connects and authenticates, this client can access Site A's networks with no problems. However vpn client on Site A ASA can not access Networks through l2l tunnel located at Site B.
View 2 Replies
View Related
Jun 4, 2012
used to be able to access pc usieng fing now can not access used fing.Accessed a win 7 client with my android. Reset the router now i can not access the win7 but able to access 2vista a different win7 pc and able to access other devices on nerwork. Can see the win 7 machine in question but can not connect with samba client.
View 2 Replies
View Related
Jun 3, 2013
I have two ASA5505 with a site to site VPN.One of the ASA is connected to the internal network 192.168.150.0.The other one is connected to 192.168.151.0.
I have also configured IPSec Cisco client VPN to the one which is plugged to 192.168.150.0.
I would like to know if it is possible for a client connected with the Cisco VPN to access the network 192.168.151.0 through the site to site VPN.
View 3 Replies
View Related
Apr 3, 2013
I´m tring to configure ASA 5505 with VPN Cleint, to access a remote network over a L2L with another ASA 5505, but no sucess. Is there any special feature to this work?
View 2 Replies
View Related
May 27, 2012
I have an issue where my vpn clients are unable to access certain vlans in my network.I have configured an ASA 5520 with VPN access using the wizard and using the ASA as a dhcp server for VPN clients. I find that this allows the clients to access server resources such as the Exchange and Domain Controller but I find that these vpn clients are unable to ping each other as well as certain vlans that I have.Is there a way to configure the ASA to use a particular vlan that is already configured on the core switches?If I create a vlan interface and set the IP of it to 10.50.x.x then the vpn clients are suddenly unable to connect to any network resources...
View 1 Replies
View Related
Mar 14, 2011
I am trying to build a remote vpn in ASA 5520 Software Version 8.3(1). I am using ASDM 6.3(1) for the configuration. I went through the SSL VPN wizard and did the configuration. I tried connecting to the ASA using anyconnect VPN and I could successfully connect the VPN. My home laptop takes an IP 192.168.60.21 (which I have defined in the wizard). Now my issue is, I can't access any office internal network from this laptop (none of the internal IP is ping ing even). Meanwhile, I could ping and rdp to this laptop(which is connectd by anyconnect VPN) from my office network. One thing I noticed is that when I give a traceroute to an internal IP from the laptop, the first hop goes to my home ISP router.
View 8 Replies
View Related
Sep 28, 2011
We have two sites connect with an IPSec L2L VPN.
-Site A: 192.168.13.0/24
-Site B: 192.168.2.0/24
On both sites we have a ASA5505(Base license) to terminate the tunnel.On Site B we also got a remote access vpn to which we can connect using the vpn client.The lan2lan tunnel works fine and so the remote access vpn.Now i want to connect to Site A using my vpn client connected to Site B. [code] There are no vpn-filters or other special policys in place..If tried to ping from my vpn client to Site A while i was debugging ipsec 255 on site B: the asa matched the l2l-tunnel for traffic sourced from 192.168.25.x to 192.168.13.x but when im doing a show crypto ipsec sa detail there are no packets getting encrypted..so of course no packets reaching my asa on site a.
View 9 Replies
View Related
Feb 13, 2013
I have one user who is unable to Access Remote Network resources when connected to the VPN on his home network. VPN shows connected and he is given a remote IP from the VPN Pool, but he cannot ping any IP on our network. When connected using Sprint Wi-Fi card he is able to connect and access remote network from the same laptop. Maybe there is some network overlap that I am missing.
see attached firewall config (zzz... being firewall public IP) and remote user route table. ASA 5505 VPN Client 5.0.07.0290
View 5 Replies
View Related
Oct 31, 2011
I have configured Clientless SSL VPN for access to ASA 5540 internal network. Still I am unable to take ssh to my core switc [code]
View 5 Replies
View Related
Feb 28, 2013
I have created a new sub-interface on our ASA 5520 for guest internet access.
My goal is to allow access to a few specific services hanging off some dmz interfaces on the same firewall and full unrestricted access to the internet only. Everything else should be out of bounds.
The order of the rules I plan to setup on the guest interface inbound are:
#1. <rules to allow access to specific services in the dmz>
#2. <block any ip access to the entire private network ip address space>
#3. <permit ip any any>
#1. These rules will give access to the guest user to services located in the dmz
#2. This rule will block all access to any services in the private ip address space (thus blocking access to all internal services)
#3. This rule is to allow access to any other services i.e. the internet.
Is this the best way to achieve my goal in the most secure way or is there a better way? i.e. is there a way to force the traffic by default to only go out the outside interface unless there is a specific rule allowing it go elsewhere?
(Of course Dynamic PAT will also be configured for traffic coming from the guest interface to the outside interface.)
View 2 Replies
View Related
Aug 23, 2011
I am using ASA 5520 with 8.2.4 IOS. I'm new to ASA/Firewall. I need to do access webserver from outside network.From Laptop (192.168.2.51), If I connect to url... it should open page from 10.10.10.50.I also need to ssh to webserver from laptop. If I ssh to 192.168.2.50 from laptop, it should connect to 10. 10. 10.50. [code]I can't get to webserver from outside network, so now, I connected laptop to directly ASA 5520 outside port with crossover cable.ASA Inside port connects to L3 switch. Webserver also connects to L3 switch. But still doesn't work.
View 9 Replies
View Related
Jun 18, 2012
I have a Cisco 881 setup with the following VPN config.
[code]...
The client is able to connect just fine to the network via VPN, but I am unable to gain access to any of the local resources. I know 192.168.1.1 has SSH running and 192.168.1.50 has telnet running but if I try to connect to either using the correct program they just timeout. I am really at a loss on why the vpn connection connects but I can not gain access to any of the resources on the VPN network.
View 3 Replies
View Related
Jan 24, 2011
i currently have a netgear wgr614v9 running the most recent firmware update and a tplink nr741nd running the latest dd wrt firmware.the netgear is my main router connected to the modem positioned in the living room attached to this is a wired ps3, wii and various laptops connect wirelessly to this. In my bedroom i have the tplink router is is setup as a client on the netgear router allowing media network drive access to the internet.
eg.
--- wired
~~~ wireless
modem-----netgear~~~~~~tplink----network drive
What i would like to achive is to be able to connect to the netgear router wirelessly and have access to the network drive attached to tplink router.I have tried a client bridge on the dd wrt firmware but this does not work at all. I have read that i need to setup a VPN on the dd wrt but i can find anything on how to do this when trying to access a drive on a second level.
View 3 Replies
View Related
Feb 21, 2012
Have cisco ASA5520 on place and i want to configure it to access my webserver outside of my network throught sftp/ftp with filezila what command to add so as port/service associate to it should be able to run?
View 1 Replies
View Related
Jan 23, 2012
We have a Cisco wireless infrastructure in place that includes a guest network with its own subnet that is a sub interface of the inside interface on our ASA 5520. There are no routes for it to be allowed access to the internal subnets. So it can only access the internet. This is primarily used by the public, but we have several non employee personnel that we only want to give internet access and force them to access the internal network through our clientless SSL vpn portal or through other internet facing internal resources such as webmail.I have done packet traces from within the ASA and the break appears to be there is no ACL allowing the traffic back into the network once the web resource replies to the request and the traffic is attempting to come back into the network from the web resource. Is that as clear as mud?
I know that this has to be a common problem and a way around this is to allow the guest wireless network access to the internal network but only for the select resources that they require. And that this can be done seemlessly by network specific routes and or alternate DNS entries, but I would like to keep this simple and just allow them to access the web resource, webmail and VPN, from the guest wireless using internet DNS servers without route trickery.
View 8 Replies
View Related
Feb 18, 2012
I'm setting up a L2L VPN Hub and Spoke. I have 3 sites (1 HUB and 2 SPOKES).
HUB-----------SPOKE1
|
|
|
SPOKE 2
HUB and SPOKE 1 is okay. My problem was the communication between HUB and SPOKE 2. PING failed on both directions. BTW, I am simulating this only in GNS3. :-). The configuration for HUB and SPOKE 1 are the same also for HUB and SPOKE 2.
Here is my show isakmp sa and ipsec sa on HUB
ciscoasa# sh isakmp sa
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
[Code].....
View 4 Replies
View Related
Apr 7, 2013
I have configured my ASA5520 to act as VPN server. It accepts connections from the internet and then it authenticates the user to a Windows 2008 Server via Radius.Everything works fine if I use the VPN client embedded in Microsoft Windows. Conversely, if I try to configure Cisco VPN Client, I cannot find where to define the PSK string.
View 3 Replies
View Related
Jun 24, 2012
I have made the following change to my ASA 5520 using ASDM to try and force VPN clients to use a self assigned certificate from the ASA. I made the following changes Remove Access VPN > Certificate Management > Identity Certificates > Add Certificate.Then I made the following change.. Remote Access VPN > Network (Client) Access > IPSec(IKEv1) Connection Profiles > Connection Profile > Edit > IKE Peer Authentication > Pre Shared key and pointed the identity certificate to the one I created in the step above.Having made this change I am still able to VPN without a certificate configured in authentication settings.I was expecting that the VPN would attempt to issue the self assigned cert to client machine?
View 1 Replies
View Related
Oct 2, 2012
I have remote branches that connect to the corporate office as a site-to-site VPN. Now the clients at the branch are getting an application that is using an unsecured port (tcp/23). I would like to use a set of ASA 5520's that I have at the corporate office, with the AnyConnect license on them. I want the client machines to establish a tunnel from the client to one of these ASA's. The ASA' then would have a connection to the VLAN that the receiving server is housed on. The trick is to just establish the tunnel from the client to the ASA that will allow the IP of the client to not be translated. So I would use the ASA as a security 'pass-through' for the clients that use this new application.
View 1 Replies
View Related
May 10, 2011
We have an ASA with software version 8.2(1) and ASDM 6.2 to use the VPN. We configure the anyconnect client with split tunnels for our vendors to access internal server and have access to the other resources in the web simultaneously. Windows XP client works fine however, the Mac OS x can only access the internal resource but not the web.we need to restrict the client to access and use only specific IP and http port.have internal and external DNS that are separated by ASA5520s all VPN terminate at the DMZ with192.168.xx.0/24 IP pool?
View 1 Replies
View Related
Nov 19, 2011
suppose i have 2 hub location and one spoke and i want to config DMVPN between them and want to keep 1 HUB as active and 2nd HUb as passive then how its possible.
View 2 Replies
View Related
Aug 12, 2012
I currently have a "hub" ASA 5505 that links to 4 sites running 877 routers. From the hub network i can connect to all sites fine but what i would like to do is to almost compartmentalise the various VPN links into little clusters.The hub ASA 5505 basically provides IP telephony through the VPN's from a PBX allowing the users at the other end of the VPN to make outgoing calls and recieve incoming calls. However, a couple of the sites would like to be able to call between eachother internally via the hub. This obviously requires traffic to be allowed between their various networks. Currently when you attempt an internal call it rings but there is no audio either way. I assume this is due to access list restrictions. I am not even sure whether what I am trying to achieve is possible. I've attached the hub and 2 spokes below. The ideal end result would be interconnectivity between the two spokes via the hub, from reading up it would seem that its possible but i can't quite get my head around it! Would it involve using different subnet masks at the hub?
View 1 Replies
View Related
Jan 12, 2012
i am trying to set up a tunnel connection between twO 2800 routers A<->B
1) destination ip is-204.x.x.x-ROUTER A2) source ip is 166.x.x.22-ROUTER B The router B has the modem connected to GE0/1 whose interface ip is 166.x.x.22 The ip-forward-protocol nd is configured as below
ip route 204.x.x.x 255.255.255.255 166.x.x.21
Also tunnel 1 configuration,isakmp policy are configured properly when i run show crypto isakmp sa it shows MM_NO_STATE,i checked the preshared key on both ends and they are same.whenever i remove the ip address of the interface Ge0/0 and ip route i can ping the 166.x.x.21 which is the modem gateway.when i revert back the configuration to the above ,the ip 166.x.x.21 cannot be pinged,the dsl connection is live though.ways to fix this so that i can make this tunnel state to QM_IDLE?
View 1 Replies
View Related
Jul 11, 2011
I want to build a "hub and spoke" topology for one of my clients. For the "HUB" , I'm planning to use an SA540, with a static public IP provided by a 4Mb SDSL. For the "spokes" (21 at the moment), I'm planning to use RV120. They will be behind a NAT, provided by a "SAGEM LIVEBOX", and a static public IP. The boss will connect to the HUB using Cisco VPN client, or quickVPN, and get access to all the spokes. Some spokes will have to connect to each other, via the HUB. I searched a long time on this forum and reading documentation, but I didn't find at the moment the answer to my question : is this topology suitable with the choosen hardwares ?
View 7 Replies
View Related
Mar 23, 2011
Imagine MPLS network. Total of 4 sites.
HQ-HUB is the only site with access to the Internet.
So if Site1 or Site2 or Site3 need to access the Internet, traffic will have to go through HQ-HUB and from there reach the Internet.I have routes 2851's on the spoke sites. Which command or mechanism you would explore in this case to make the spoke sites point to the HQ-HUB to reach the Internet?
Would you do this based on DNS settings or getting an access-list & static route defining when the spoke routers traffic need to go the internet, point to the HUB-HQ as the default?
View 3 Replies
View Related
Aug 15, 2011
My basic question is, does Cisco VPN Client allow two simultaneous VPN connections at once?I want to set up the following:User Client (Remote Access VPN via Internet)--> Head Office ASA 5520 A/S Pair --> (Remote Acces VPN via Internet) --> Branch Office ASA 5510S+ A/S Pair,So, in order to access the branch office system, the user must:Connect to Head Office ASA peer via Cisco VPN Client (user/password authentication),Head Office ASA peer gives a private 172.16.1.x IP, and is configured to route all requests to Branch Office's public ASA IP via it's own public IP address. Once Head Office VPN established, user establishes a SECOND VPN tunnel from Cisco VPN client (user/password and cert-based auth).
View 3 Replies
View Related
Apr 21, 2013
CISCO ASA 5520 -K9 .Client can connects ASA server and get ip address(172.168.31.X),but can't ping ASA inside interface ip address and other servers in lan .
View 2 Replies
View Related
Sep 25, 2011
I currently have a Cisco 5520 ASA which is up and running and the users are able to connect to Anyconnect to VPN into the network. However, users plugged into the internal network inside the ASA are unable to connect to the vpn address and download the Anyconnect Client. I think this may be to do with reverse NAT missing?
View 4 Replies
View Related
Sep 15, 2011
I want to setup NAT with ASDM on ASA for a client and I can not make it work. I have several interface:
Inside: 10.97.0.1 / 24
Outside: 10.0.1.70 /24
Interco: 192.168.6.1 /24
Other Sites: 10.26.0.4 /24
All routing in the network is Ok My customer want to access a server @ ip 10.194.70.1 in https on the interface Interco with his nat address as 10.97.0.11 .This server must be accessible with the address 10.97.0.11:443 from interfaces inside, outside and other sites.And source address must be nated with original destination address 10.97.0.11 to be redirected on 10.194.70.1.
View 7 Replies
View Related
Oct 24, 2012
can I use Windows 7 Native VPN client to connect to the ASA..and are there docs out there that support install and config ? I heard it is possible but not able to confirm .
View 1 Replies
View Related
Apr 7, 2011
I am having real problems trying to build resiliency into a hub and spoke frame relay scenario. I know the hub is a single point of failure. Is there any way to put some resilience into the network? There is 4 attached branch offices.
View 8 Replies
View Related
Apr 18, 2013
I have a need to Remote Desktop connect to company’s employees for support then they are abroad and using Cisco AnyConnect client.Cisco AnyConnect client connection works fine, clients can reach company’s inside network without problems, but I cannot make revers connection, I cannot Remote Desktop connect or ping VPN clients from companies inside network. I cannot ping clients from ASA too.I am using ASA 5520, Cisco Adaptive Security Appliance Software Version 8.4(3) Device Manager Version 6.4(7), and Cisco AnyConnect VPN Client 2.2.0133. Protocol Encryption- AnyConnect-Parent SSL – Tunnel DTLS-RC4 RC4 AES 128.
View 0 Replies
View Related
