I want to assign multiple IP addresses for VPN service on same physical interface. But ASA don't support secondary address,loopback interface.So, I tried to use IP addresses assigned on another reserved interface ,but VPN connection could not be established.Thats,s why I want to assign multiple VPN addresses,I want to move and add old ASA's VPN's IP address to new ASA located at DataCenter.
View 2 RepliesI have an ASA5515 and our remote sites which have a mesh topology of VPN. At some times of the day router to particular links are down do to the ISP core, but the tunnels from the same firewall can communicate to other sites. Is it possible to have a way where you could route traffic to another ASA which has a connection to both the ASA which want to communicate and have the traffic hairpinned, I know this is possible but is it possible to make this automated.
View 5 Replies View RelatedI have been working for a while trying to get the Linux AnyConnect Client to Connect to the ASA using IKEV2 and EC Certs. I have gotten it to work with SSL, but I can't seem to figure out how to get IKEV2 turned on. On the profile screen (attached) in the ASA when I check IKEV2 I get the cert screen, I check the cert, but then it fails to bring the cert and unchecks the block. The Network Design is simple. ASA IP on high side (outside) 172.20.206.8 with the client at 172.20.206.50. Local LAN is at 10.200.203.0/24.
View 7 Replies View RelatedLooking at migrating from the following:
PIX-515EPIX Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)51
to
ASA5515Cisco Adaptive Security Appliance Software Version 8.6(1)Device Manager Version 6.6(1)
Is this migration directly supported, or do I need to downgrade first?
I have recently procured ASA5515-IPS-K9 for my own R & D. In that device I want to achive following milestone: Perform static routing , relay DHCP, cache flowEnable IPS with auto updateQoS for Voice and WAN traffic Protect regional Campus/LAN, WAN, regional Servers from regional Campus/LAN, WAN and InternetAllow traffic from well-known and given portsSNAT for the regional servers with given portsACL for ssh only from admin PC with TACACAS rightMaintain SNMP with Cacti, Nagois, LMS, TACACASAll LNS servers to be added as name serversMaintain time with ntp.xxx.yyy.bd.
View 2 Replies View RelatedCould I get a validation that this config is correct in that it allows inbound access to the web server and that I should be able to ping it from my inside interface.
I tried to use the example code from Cisco DocID: 115904 for DMZ WebServer, but I found the object NAT parts did not work with my 8.6 IOS so I modified them as shown in my config.Example from 115904 doc.
!!!!
object network WebServerPublic
host 24.25.26.80
object network WebServerPrivate
host 192.168.1.80
nat(dmz,outside) static WebServerPublic service tcp www www ---> this does not code
!!!!
With the below code I do not get a ping reply sourcing from a 10.1.0.X host to 192.168.1.80 web server.And I cannot browse in from the outside to it either.I do see the MAC for 192.168.1.80 in the ASA's arp cache for the dmz interface.The web server is on a VMware ESX environment and I'm not sure it is set up correctly.
!
ASA Version 8.6(1)2
!
hostname A5515
!
interface GigabitEthernet0/0
[code]....
I was purchase ASA5515-K9 (Without IPS Edition) firewall and this is run smoothly our network. But right now i want to IPS facilities. Can i have any licnese purchase and upgrade from ASA5515-K9 to ASA5515-IPS-K9 abd use IPS edition ?
View 1 Replies View RelatedI am setting up an ASA5515 to replace an existing Linux based firewall. Unfortunately the ASA5515 does not support source based routing.I have two internet connections currently used for specific connections - the second connection is NOT a failover connection.I have the default route to Internet connection 1.I want to route smtp out the second Internet connection.The routers connecting to the internet are a 877 and an 878The options I am considering is a layer 3 switch between the firewall and the routers to enable source based routing or replacing the 2 routers with a single router and the appropriate wic interfaces.
View 2 Replies View RelatedI was given multiple ips but how can i be able to use it in just one router?
View 2 Replies View RelatedI need to put a few cameras, without a server, on a static WAN ip address. Do I just assign them a static LAN ip address(for example 192.168.1.200), make sure the port they use is open, then type the WAN static ip address then colon and the last address? Like this.....I'm making up the WAN address....45.34.55.334:200
View 1 Replies View RelatedI lost it on my old laptop. Figured it was time to get a new computer anyways, we bought a new one, along with a Playbook. Both the new computer and the Playbook have had this problem, though they were able to fix it.They all use Wi-Fi.
View 2 Replies View RelatedI am having 5 IP addresses assigned to me. I have one commercial/business modem/gateway/router. If I want to have the advantage of separate lines (go with this for now) how else can the gateway do it other than simply passing the IP directly through, no router function, basically a modem/switch, everything else not there.
View 4 Replies View RelatedAfter pulling a brand new ASA5515 out of the box this morning, I spent countless hours scratching my head wondering why:
1. I cannot establish an HTTPS connection to the Management port - https://192.168.1.1/admin
2. When connecting via the console port I get prompted with a username and password sequence that I don't know
I get an SSL Version Error message when I try to connect with any browser. although I did find a way to resolve it, it requires a console port connection which is not working either.This is not my typical experience with the console or ASDM port setup.
im lookin to establish a a multiple L2L ips tunnels ( one tunnel for each subnet) from my cisco asa 5510 to the same destination. should the cisco asa capable of this ?
View 6 Replies View Relatedconfigure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I try I get an error message with a duplicate IP address error. On Catalyst switches it can be done, but on Small Business?
View 1 Replies View RelatedMy ISP assigns IP's through a standard motorola cable modem via DHCP server. I can pay extra for a persistent IP which uses the MAC of my switch and assigns an IP. Is there a way to get multiple public IP address's from the modem using a switch?For example. Can I plug the modem into the switch and then plug a computer server into the switch and get an IP assigned to that servers MAC address and then also have another server attached to another port on the switch and get a different public IP for that servers MAC address?
View 7 Replies View RelatedI have a i-ball 150M wireless-N ADSL2+ Router device in that , in the NAT tab, i have activated DMZ at my static ip with a private address 192.168.1.224 , so that that ip enabled device can be access to anywhere in public network.I want that using this single static ip , How to configure two private address devices in DMZ, so that both of ip enabled devices can be access in public network.
View 3 Replies View RelatedI am trying to get two external addresses to PAT to different ports on the same address in the dmz.
Object NAT is configured as follows:
object network Obj-192.168.1.20-1
nat (dmz,outside) static Obj-External-1 service tcp https https
object network Onj-192.168.1.20-2
nat (dmz,outside) static Obj-External-2 service tcp 2000 https
Obj-192.168.1.20-1 and Obj-192.168.1.20-2 contain the same host address.
The idea being that traffic destined for Obj-External-1 on port 443 will be forwarded to Obj-192.168.1.20-1 on port 443. Traffic for Obj-External-2 on port 443 will be forwarded to Obj-192.168.20-2 on port 2000.
Traffic for the first object, Obj-192.168.1.20-1, works but traffic for the second does not.
I have a client that needs a VPN with multiple network address ranges on the far end of the IPSEC tunnel. Is this possible with this RV180 unit?
View 1 Replies View RelatedWe have several remote sites with Linksys WRVS4400N and Smoothwall firewall/vpn devices. I need these sites to be able to connect to multiple dis-contiguous subnets at our main office. This was easily done with smoothwall and linksys. You create a separate tunnel for each subnet and voila, you're done. However, when I tried this with our newly installed ASA, it will not let me create multiple tunnels to the same remote peer address. This is a problem since these sites only have a single static public IP address. Am i missing something or does the ASA not allow connections to/from multiple subnets form a site with a single peer address?
View 13 Replies View RelatedGot an ASA5520 running V8.2(3) and we want to upgrade our internet bandwidth. Our ISP says OK but we need to install different physical circuit, upgrade CPE router, etc.
Then they say, btw your globally allocated IPs will change - this is a problem as we have Site-to-Site VPN Tunnels, IPSEC RA, etc.
ISP are proposing to give us a 3 month period whereby old & new IP blocks will be routed to our ASA (by means of secondary IP address on their Cisco CPE).
Multiple IPs on the same physical i/f on the ASA require sub-interfaces/IP Addresses/VLAN ids on my "outside" i/f.
Is this going to horiibly break Site-to-Site VPN Tunnesl, IPSEC remote access ?
Will VLANs work at all with IPSEC on the "oustide" i/f at all ?
I have a situation where a user needs more than one office extend AP in his home. My office extend controller is a 5508 running 7.0.220.0. Are there any issues NATing multiple OE APs to a single address? My initial lab results indicate that each of the AP's associate with the controller and establish a DTLS tunnel. I see the SSIDs get pushed to the AP and then it seems to restart the process never being fully operational. Is there a workaround that will allow me to run mutliple OE APs?
View 12 Replies View RelatedI am working with MS Windows 2008 R2 and a Belkin F5D8635-4v1 router.
I have already set up a dynamic IP address which points to my router at home. In my home network I have multiple PC's that I would like to access from the internet. I would like to achieve this without needing to change my port forwarding rules on my router each time...
My thoughts are that I use a single dynamic IP address pointed to my router. My router then forwards to a server with some sort of software that can then forward to the correct PC based on the host name.
So I have 3 domains set up all pointing to the router's IP address:
dest1.domain.com -> 41.xxx.xxx.45
dest2.domain.com -> 41.xxx.xxx.45
dest3.domain.com -> 41.xxx.xxx.45
The router is not smart enough to redirect by host name, so it will just forward everything to 10.0.0.20 The server based at 10.0.0.20 must then have software to now redetermine the target based on the host name. The rules would be set up as follows:
dest1.domain.com -> 10.0.0.22
dest2.domain.com -> 10.0.0.24
dest3.domain.com -> 10.0.0.26
how to configure a site to site tunnel using IKEv2 between our offices using an ASA 5515-X and a Cisco 3925 router running IOS 15.2 Connecting ASA to ASA and ASA to Router via IKEv1 works fine. Want to take advantage of the improvements in IKEv2 but I'm having difficulty with the ikev2 setup on the router. Here is the pertinent ASA side config--
ASA IP: 5.5.5.5
Router IP: 10.10.10.10
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1
[Code].....
We have an ASA5515 at HQ and multiple sites with ASA5505 units. All of these units are connected via site to site VPN in mm. They also have static ip's.mwe have two sites that we are currently attempting to connect back to HQ in aggressive mode but are unsuccessful.
View 1 Replies View Relatedhow i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedIs it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedI am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
i`m facing a problem configuring the mentioned access point to act as stand alone access point with multiple SSID assigned to differnet VLANs the problem is that
1) i`m not able to broadcast the both SSIDs in the same time from the Access point
2) i need to make the radius server to manage the SSID access for the wireless clients (trying to find a way in which the aceess point sends a log for the radius server containing the VLAN id /IP address of the the SSID) you may find the below info about the IOS ver. & the configuration?
i`m running IOS /c1100-k9w7-mx.123-8.JEE/c1100-k9w7-mx.123-8.JEE?
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View Related