Cisco WAN :: 6503 Boot Variable Is Getting Wiped
Feb 9, 2011
I've got a 6503, SupII/MSFC running Native code, so I'm pointing the boot variable to disk0: (bootflash is not large enough for the image file). In using the wr erase, the boot variable is getting wiped as the wr erase removes all nvram files, and apparently the boot variable is stored there. I also tried the erase start, which also hits everything in nvram.
So, any clean way to wipe a config without forcing the router into ROMMON to reset the boot variable, or do I need to just expect that is part of the standard approach?
View 1 Replies
ADVERTISEMENT
Dec 14, 2012
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies
View Related
Dec 26, 2011
I need my Wep number which has been wiped off of the modem
View 1 Replies
View Related
Apr 4, 2012
i recently had to wipe hardrive of my laptop and am having trouble getting hooked back up to my linksys E/1000 , who can i contact about getting password and network name
View 2 Replies
View Related
Jan 15, 2012
We recently deployed a FWSM on our 6503-e boxes (w/ sup720). NAT is working (PAT) but the issue I am seeing is private traffic from remote sites is not being allowed through the FW. I was able to get the remote site to ping the FWSM itself (inside address), but no hosts behind it. Maybe an ACL issue? Also when I turn off NAT on the remote end, I can than access everything (We are NATng on both ends). Im a routing guy by nature so I will defer this to the security guys out there.
Topology
Hosts (inside/10.15.25.0/24) > FWSM (outside/public IP) -> Core Router -> MPLS CLOUD -> Core Router (NATng) - > Hosts (192.168.1.0/24)
ACLs applied to inside/outside interface
FWSM# show access-list ATX-ALLOW-IN
access-list ATX-ALLOW-IN; 15 elements
access-list ATX-ALLOW-IN extended permit tcp any any (hitcnt=222)
[Code]....
View 3 Replies
View Related
Aug 7, 2012
I want to migrate a Cat 6503-E VSS to Cat 6509E VSS. We plan to use the same supervisor that we have on the Cat6503E, for minimizing the configuration change on the Doing this, the vss link will need to be changed, due to the fact that the supervisor slot will change with the Cat 6509, slot 5 instead of 1.
Question: is there a way to just change the vsl-link interface on a existing VSS ?
View 3 Replies
View Related
Apr 11, 2013
I have an issue with a customers 6503 with Sup-2T cards, where we are locked out of the console due to an authentication configuration error. So tried several times to get the card into rommon, with no success.
Checking through the various documents on CCO I dont find any reference to rommon on this card, but do find information on using the CMP to support the supervisor. I logged into the CMP but couldn't find a way from there to do a password reccovery either.So, is the `normal' IOS rommon/password recovery method supported.
View 2 Replies
View Related
Oct 16, 2012
I am looking at running MPLS from from one datacentre to the other (we have a layer2 interconnect and can run jumbo frames) I need about 70 access ports (each in a seperate VRF) at the new datacentre
I am looking at :
2x 6503'-Es with sup720-3B and a 48x port linecard
or
2x 7201 router with 2x 2960-S layer 2 access switches.
View 1 Replies
View Related
Oct 24, 2011
i'd like to configure OSPF on a Catalyst 6503 IOS 12.2.17.i habe an Gi1/9 with the ip address 192.168.97.30/24 and a VLAN 19 with the IP Address 192.168.19.0/24.I configured OSPF like this
router ospf 1
network 192.168.97.0 0.0.0.255 area 10.5.0.0
network 192.168.19.0 0.0.0.255 area 10.5.0.0
on the ospf peer is see that the adjaceny is established but i don't get the routes for the 192.168.19.0 network i checked the ip ospf interface vlan 19; i got ospf is not enabled on the interface then i tried to configure
int vlan 19
ip ospf 1 area 10.5.0.0
but it does not access ip ospf 1
View 3 Replies
View Related
Sep 23, 2011
I Want To Boot PC From LAN.
View 2 Replies
View Related
Jun 21, 2011
We have got a big problem with our NAM (WS-SVC-NAM-1) - it does not boot. We have got a second one and in an other chassis. I changed the chassis, and RAM and Flash from the other one. RAM and Flash are ok.
We checked the disc (hardware) with an Ontrack-tool -it is OK.
environment: 6500 VSS
sh logging:
Jun 17 13:18:24: SW1_SP: Switch 1 Physical Slot 7 - Module Type LINE_CARD inserted
sm(cygnus_oir_bay slot7), running yes, state wait_til_online
Last transition recorded: (offline)-> empty (remove)-> empty_clr_persist (remove)-> empty (insert)-> may_be_occupied (timer)-> occupied (known)-> can_power_on (yes_power)-> powered_on (real_power_on)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online
View 2 Replies
View Related
Sep 29, 2011
is it possible to boot the image from a usb stick on a 1812? if so, what are the requirements?
View 14 Replies
View Related
Aug 22, 2012
I've got a Cisco 2621 with this IOS image in flash: c2600-i-mz.120-7.bin (the only IOS in flash). When I power up the router, the following errors occur:
open: file "n" not found
open(): Open Error = -1
loadprog: error - fileopen
boot: cannot load "flash:n"
I have to press "Ctr l" and "break" to enter Roman, there i can use the boot command to start the IOS. Configuration register is set to 0x2102, all running config should be factory default.
What I have to do to boot the IOS directly when i power up my router (without entering Roman mode...)?
View 4 Replies
View Related
Feb 13, 2011
want to boot my network how can i do that?
View 1 Replies
View Related
Apr 2, 2013
I have a netbook, so it have not dvd drive. I haved usb flash drive, but now it not work. I want to install windows on my netbook, but i cant as there are no dvd drive and flash drive.But i have a PC computer, which have dvd drive.I want to know, that is it possible to boot my PC's dvd rom and install windows on my netbook.
View 14 Replies
View Related
Aug 5, 2011
I've got a fully working 877w that I'm trying to get to boot from tftp, but I just can't seem to get that going.I have a tftp server running and can copy images back and forth without any trouble.I have this in my config:boot-start-markerboot system tftp c870-advipservicesk9-mz.124-24.T2.bin 192.168.1.200boot-end-markerDuring the boot process I get an error message that says there is a missing or illegal ip but I really don't see how that can be as my tftp server is 192.168.1.200 just like my config says.
View 16 Replies
View Related
Jun 5, 2013
I have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
View 2 Replies
View Related
Apr 20, 2010
I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
View 4 Replies
View Related
May 9, 2011
I'm having an issue, with an WS-SVC-FWM-1-K9.
The card doesn't boot properly, it tries to boot, but after a while the 6500 puts it in shutdown.
I've noticed that it has 2 RJ45 ports in the board, I've plugged my console cable, but i only get characters with the default serial configuration.
Any information about the port configurations? Is the port "PC Console" the correct one?
View 3 Replies
View Related
Jul 29, 2010
My ASA5505 is not boot up. I did upload ios from rommon mode with tftp and tftpdnld.It is uploaded successfully after reboot it stopped at cisco logo sing.
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
I deleted old ios and upload new but look same.
View 16 Replies
View Related
May 31, 2012
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
View 3 Replies
View Related
Feb 7, 2013
I have two 877's that have both reset with the following messages on boot, and dir of flash and lost+found/It appears that there is a IOS on the flash? but rommon doesn't know where it is. I tried to "set" with no luck as set is read.
I have noticed that the IOS is 0 size. [code]
View 2 Replies
View Related
Dec 16, 2012
I have added a new NME-WAE-502-K9 in one of our remote Cisco 2811 routers. This module doesn´t boot, and it seems to be in a loop trying to boot. [code]
View 6 Replies
View Related
Feb 6, 2012
I need Cisco router 2800 series boot ios image from network(tftp), when flash is corrupted or router doesn't see it, so it is impossible ? Command, i used boot system tftp: ios.bin but this does not work.
View 9 Replies
View Related
Dec 11, 2012
I purchased several 1921 routers and the last two I setup get the following error during bootup:
%SYS-6-READ_BOOTFILE_FAIL: tftp://255.255.255.255/1:aaa1386.bin No usable interfaces.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
%MAINBOARD_GE-3-SHUTDOWN: FPA PKT pool holding 512 particles.boot of "1:aaa1386.
bin" using boot helper "usbflash0:c1900-universalk9-mz.SPA.151-4.M4.bin" failed
error returned: No usable interfaces
loadprog: error - on file open
boot: cannot load "1:aaa1386.bin"
The router moves on and eventually comes up fine and is operational. What this error is an if I can get rid of it?
View 5 Replies
View Related
Feb 24, 2012
I have a problem with 1841 router - It wont't boot up and there is a message
Correcting primary nv_flash
View 2 Replies
View Related
Dec 27, 2011
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
View 2 Replies
View Related
May 18, 2011
we have a problem with a Cisco 1841 router while booting. The router is loading the image from the CF card but gets stucked at this point:
This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be foundURL
View 1 Replies
View Related
Feb 22, 2012
how to upgrade a Cisco Pix 525 boot rom from 4.0 to 4.3. Is it a physical chip or software upgrade? Is it needed to upgrade to latest IOS on Cisco Pix 525 to 8.0. Where can I find more information on it?
View 1 Replies
View Related
Apr 25, 2013
I have a Cisco ASA 5505 I've configured as a DHCP server. I'm getting DHCP on workstations attached to the appliance, but I'm getting the following message when the appliance loads:DHCP Client: can't enable DHCP Client when DHCP Server/Relay is running on the interface DHCP: Interface 'inside' is currently configured as SERVER and cannot be changed to a CLIENT by a CLIENT featureI'm not trying to configure this thing as a client, so I'm not sure why the system is producing this message.
View 2 Replies
View Related
Oct 11, 2011
I have a customer who is concerned with the power draw on the new switches we're deploying.They only have 20 amp breakers in their closets and fear popping them on switch boot. The customer is under the impression that a switch will pull full power on boot. So a 3560X with an 1100w PSU will draw the full 1100w on startup. Ive never heard this and it doest make much sense to me, but I need to verify.
View 10 Replies
View Related
Jul 27, 2011
I have a 2621 router, because I want an image of about 21M, I upgraded as follows:
IOS = 32M
RAM = 64M
ROM VERSION = 12.2
However, when I power up my router, it goes into a boot loop, and I see the following messages:
NOT ENOUGH MEMORY IN THE SYSTEM TO RUN THIS IMAGE
***SYSTEM RECEIVED A SOFTWARE FORCED CRASH***
how to overcome this error, and successfully upgrade, so I could load my new image?
View 1 Replies
View Related
Dec 30, 2011
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
View 6 Replies
View Related
